EN 12733:2001+A1:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Agricultural and forestry machinery - Pedestrian controlled motor mowers - Safety
07-23-2013
03-04-2009
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or measures
5.1 General
5.2 Engine starting and stopping devices
5.3 Manual controls
5.4 Marking of controls
5.5 Controls of the movement of the machine and of the
blade(s)
5.6 Reverse gear
5.7 Handlebars
5.8 Pressurized components
5.9 Liquid spillage
5.10 Exhaust system
5.11 Steering mechanism
5.12 Brakes
5.13 Electrical installation
5.14 Noise
5.15 Vibration
6 Specific requirements
6.1 Sickle bar mowers
6.2 Grassland mowers
6.3 Flail mowers
6.4 Scrub clearing machines
7 Information for use
7.1 Instruction handbook
7.2 Marking
Annex A (normative) List of hazards
Annex B (normative) Noise test code for motor mowers -
Engineering method (grade 2)
B.0 Scope
B.1 A-weighted sound power level determination
B.2 A-weighted emission sound pressure level determination
B.3 Requirements for test floor
B.4 Installation, mounting and operating conditions
B.5 Measurement uncertainties and declaration of noise
emission values
B.6 Information to be recorded and reported
Annex C (normative) Vibration measurement of motor mowers
C.1 Quantities to be measured
C.2 Instrumentation
C.3 Measurement direction and measurement location
C.4 Test procedure
C.5 Measurement procedure
C.6 Determination of the measurement result
Annex D (normative) Foot probe test
D.1 Test equipment
D.2 Test method
D.3 Test acceptance
Annex E (normative) Material of protective skirts
E.1 Tearing resistance test
E.2 Perforation resistance test
E.3 Wear resistance test
Annex F (normative) Corrugated fibreboard penetration tests
on grassland mowers - Test enclosure wall
panels
F.1 Purpose
F.2 Test fixture
F.3 Fibreboard samples
F.4 Procedure
F.5 Acceptance criteria
Annex G (normative) Target elevation areas
G.1 Lower elevation target
G.2 Middle elevation target
G.3 Top elevation target
G.4 Operator target area
Annex H (normative) Test enclosure
H.1 Base
H.2 Target composition
Annex I (normative) Thrown object test for flail mower
I.1 Principle
I.2 Test installation
I.3 Test procedure
I.4 Test result
I.5 Acceptance criteria
Annex J (normative) Thrown object test for scrub clearing
machine
J.1 Test equipment
J.2 Test method
J.3 Data sheet - Thrown object test for scrub clearing
machine
Annex K (informative) Example of a material and construction
fulfilling the requirements for an
artificial surface
K.1 Material
K.2 Construction
Annex L (informative) Examples of machines
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC, amended by Directive 98/79/EC
Annex ZB (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.