EN 1277:2003
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints
Superseded date
02-19-2022
Published date
12-10-2003
Publisher
Foreword
1 Scope
2 Principle
3 Apparatus
4 Test pieces
5 Test temperature
6 Procedure
7 Test report
Annex A (normative) Modification of test parameters
This European standard specifies three basic test pressures for determining the leaktightness of elastomeric sealing ring type joints for buried thermoplastics non-pressure piping systems.Unless otherwise specified in the referring standard, the methods pressures used are the following:-p1: internal negative air pressure (partial vacuum);-p2: a low internal hydrostatic pressure;-p3: a higher internal hydrostatic pressure.It also describes four test conditions under which the test can be executed, as follows:A:without any additional diametric or angular deflection;B:with diametric deflection;C:with angular deflection;D:with simultaneous angular and diametric deflection.These conditions can be applied individually or in combination. The applicable selection of the method(s) and the condition(s) should be specified in the referring standard.
| Committee |
CEN/TC 155
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNE-EN 1277:2004 | Identical |
| I.S. EN 1277:2004 | Identical |
| SS-EN 1277:2004 | Identical |
| UNI EN 1277 : 2005 | Identical |
| SN EN 1277 : 2004 | Identical |
| NF EN 1277 : 2004 | Identical |
| ONORM EN 1277 : 2004 | Identical |
| NBN EN 1277 : 2004 | Identical |
| PN EN 1277 : 2005 | Identical |
| NEN EN 1277 : 2004 | Identical |
| BS EN 1277:2003 | Identical |
| NS EN 1277 : 2ED 2004 | Identical |
| DIN EN 1277:2004-03 | Identical |
| BS EN 1519-1:2000 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE) Specifications for pipes, fittings and the system |
| 04/30118849 DC : DRAFT SEP 2004 | EN 15013 - PLASTICS PIPING SYSTEMS - NON-PRESSURE DRAINAGE AND SEWERAGE SYSTEMS BURIED IN GROUND |
| I.S. EN 1519-1:1999 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| ISO 21138-3:2007 | Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 3: Pipes and fittings with non-smooth external surface, Type B |
| 11/30239903 DC : DRAFT MAR 2011 | BS EN 15013 - PLASTICS PIPING SYSTEMS - NON-PRESSURE DRAINAGE AND SEWERAGE PIPING COMPONENTS BURIED IN GROUND - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| 06/30136260 DC : DRAFT MAR 2006 | ISO 21138-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYLCHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1 - MATERIAL AND PERFORMANCE SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEMS |
| EN 1519-1:1999 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| BS EN 13476-3 : 2007 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B |
| BS EN 1566-1:2000 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C) Specification for pipes, fittings and the system |
| EN 13566-2:2005 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes |
| DIN EN 13476-2:2007-08 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A |
| PREN 1329-1 : DRAFT 2013 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| 05/30131849 DC : DRAFT APR 2005 | ISO 8772 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) |
| 07/30165577 DC : 0 | BS EN 1852-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| DIN EN 13476-3:2015-11 (Draft) | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B |
| ISO 8773:2006 | Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP) |
| EN 1566-1:1998 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system |
| BS EN 1329-1 : 2014 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| EN 1565-1:1998 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system |
| DIN EN 13566-2:2006-02 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 2: LINING WITH CONTINUOUS PIPES |
| NF EN 13598-1 : 2011 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| BS EN 13566-2:2005 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Lining with continuous pipes |
| VDI 3462 Blatt 1:2014-12 | Emission control - Wood machining and processing - Raw wood processing |
| 13/30280703 DC : 0 | BS EN 1329-1 - PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| 05/30131855 DC : DRAFT APR 2005 | ISO 8773 - PLASTICS PIPING SYSTEMS FOR UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) |
| BS EN 13476-2:2007 | Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for pipes and fittings with smooth internal and external surface and the system, Type A |
| 06/30124428 DC : 0 | EN 13598-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY (VINYL CHLORIDE)(PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS |
| 03/102186 DC : DRAFT AUG 2003 | EN 14758-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-M) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| EN 1455-1:1999 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system |
| I.S. EN 1329-1:2014 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| DIN EN 13476-1:2015-11 (Draft) | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS |
| 14/30297456 DC : 0 | BS EN 15013 - PLASTICS PIPING SYSTEMS - NON-PRESSURE DRAINAGE AND SEWERAGE PIPING COMPONENTS BURIED IN GROUND - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| PREN 15012 : DRAFT 2014 | PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR NON PRESSURE SOIL AND WASTE DISCHARGE WITHIN THE BUILDING STRUCTURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| BS EN 13598-1:2010 | Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for ancillary fittings including shallow inspection chambers |
| BS EN 1401-1:2009 | Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U) Specifications for pipes, fittings and the system |
| I.S. EN 13598-1:2010 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| UNI EN 1401-1 : 2009 | PLASTICS PIPING SYSTEMS FOR NON- PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| UNI EN 13598-1 : 2011 | PLASTICS PIPING SYSTEMS FOR NON- PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VILYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| ISO 8772:2006 | Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE) |
| ISO 21138-2:2007 | Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Pipes and fittings with smooth external surface, Type A |
| UNI EN 1329-1 : 2014 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| BS EN 13476-1:2007 | Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) General requirements and performance characteristics |
| 14/30297459 DC : 0 | BS EN 15012 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR NON PRESSURE SOIL AND WASTE DISCHARGE WITHIN THE BUILDING STRUCTURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| ISO 21138-1:2007 | Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Material specifications and performance criteria for pipes, fittings and system |
| ISO 4435:2003 | Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U) |
| I.S. EN 1455-1:1999 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) - PART 1: REQUIREMENTS FOR PIPES, FITTINGS AND THE SYSTEM |
| DIN EN 13476-2:2015-11 (Draft) | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A |
| BS EN 1455-1:2000 | Plastics piping systems for soil and waste (low and high temperature) within the building structure. Acrylonitrile-butadiene-styrene (ABS) Specifications for pipes, fittings and the system |
| DIN EN 13598-1:2011-02 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| UNE-EN 13598-1:2011 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers |
| EN 13598-1:2010 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers |
| EN 1401-1:2009 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| 06/30136263 DC : DRAFT MAR 2006 | ISO 21138-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYLCHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2 - PIPES AND FITTINGS WITH SMOOTH EXTERNAL SURFACE - TYPE A |
| 10/30217319 DC : 0 | BS EN 13598-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| 02/121064 DC : DRAFT MAR 2002 | PREN 13566-2 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 2: LINING WITH CONTINUOUS PIPES |
| EN 1329-1:2014+A1:2018 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems |
| DIN EN 1401-1:2009-07 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| DIN EN 13598-1 E : 2011 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS |
| I.S. EN 1401-1:2009 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM |
| BS EN 1565-1:2000 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Styrene copolymer blends (SAN + PVC) Specifications for pipes, fittings and the system |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.