• There are no items in your cart

EN 12952-8:2002

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

Water-tube boilers and auxiliary installations - Part 8: Requirements for firing systems for liquid and gaseous fuels for the boiler
Withdrawn date

11-30-2002

Published date

05-22-2002

Foreword
1 Scope
   1.1 Firing systems
   1.2 Fuels
   1.3 Operation
2 Normative references
3 Terms and definitions
4 Fuel supply
   4.1 General
   4.2 Fuel transfer and preparation
   4.3 Fuel lines
   4.4 Safety shut-off devices (Safety trip valves)
5 Equipment for air supply and flue gas discharge
   5.1 Air supply
   5.2 Air/fuel ratio
   5.3 Flue gas discharge
6 Firing system
   6.1 Burners
   6.2 Flue gas recirculation
   6.3 Control and monitoring
   6.4 Electrical equipment
   6.5 Safety precautions
   6.6 Common stack for several firing systems
7 Operating manual
8 Particular requirements for firing systems burning gaseous
   fuels with high relative density
   8.1 Main firing systems
   8.2 Ignition burner systems
Annex A (normative) Chemical recovery boiler (black liquor
        boiler)
   A.1 General
   A.2 Additional requirements for the firing system for
        black liquor in the chemical recovery boiler
   A.3 Special requirements for oil- or gas-firing for
        chemical recovery boilers
Annex B (informative) Operational requirements for permanent
        supervised firing systems for liquid and gaseous fuels
   B.1 General
   B.2 Operation
   B.3 Fuel preparation
   B.4 Safety shutoff devices
   B.5 Air/fuel ratio
   B.6 Modification of firing, burner or air/fuel
        ratio setting
   B.7 Control and monitoring
   B.8 Purging, start-up and shut down
   B.9 Emergency operation
   B.10 Operating and maintenance instructions
   B.11 Firing systems burning gaseous fuels with relative
        density
Annex ZA (informative) Clauses of this European Standard
         addressing essential safety requirements or other
         provisions of the Pressure Equipment Directives
Bibliography

1. Firing systems: These requirements apply to oil and gas firing systems of steam and hot water generators. For multifuel firing systems using separate or combined burners these requirements shall apply to the oil and/or gas firing part involved. Where several fuels are burnt simultaneously, improved safety measures may be necessary, especially in respect to limitation of heat input into the firing system and proper air supply to the individual fuels. 2. Fuels (...) 3. Operation (...)

Committee
CEN/TC 269
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Withdrawn

10/30202723 DC : DRAFT JUNE 2010 BS EN 12952-7 - WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 7: REQUIREMENTS FOR EQUIPMENT FOR THE BOILER
EEMUA 184 : 2009 GUIDE TO THE ISOLATION OF PRESSURE RELIEVING DEVICES
S.R. CEN/TR 16787:2014 INDUSTRIAL GAS INSTALLATION - GUIDELINE
DIN EN 12952-7:2013-01 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 7: REQUIREMENTS FOR EQUIPMENT FOR THE BOILER
DIN EN 12952-9:2003-04 Water-tube boilers and auxiliary installations - Part 9: Requirements for firing systems for pulverized solid fuels for the boiler
BS EN 12952-7:2002 Water-tube boilers and auxiliary installations Requirements for equipment for the boiler
DIN EN 12952-13:2003-06 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 13: REQUIREMENTS FOR FLUE GAS CLEANING SYSTEMS
I.S. EN 12952-7:2012 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 7: REQUIREMENTS FOR EQUIPMENT FOR THE BOILER
I.S. EN 12952-1:2015 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 1: GENERAL
EN 12952-1:2015 Water-tube boilers and auxiliary installations - Part 1: General
EN 12952-13:2003/A1:2003 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 13: REQUIREMENTS FOR FLUE GAS CLEANING SYSTEMS
EN 12952-16:2002 Water-tube boilers and auxiliary installations - Part 16: Requirements for grate and fluidized-bed firing systems for solid fuels for the boiler
EN 12952-9:2002 Water-tube boilers and auxiliary installations - Part 9: Requirements for firing systems for pulverized solid fuels for the boiler
EN 12952-7:2012 Water-tube boilers and auxiliary installations - Part 7: Requirements for equipment for the boiler
EN 12953-12:2003 Shell boilers - Part 12: Requirements for grate firing systems for solid fuels for the boiler
PREN 12952-7 : DRAFT 2010 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 7: REQUIREMENTS FOR EQUIPMENT FOR THE BOILER
CEN/TR 16787:2014 Industrial Gas Installation - Guideline
I.S. EN 50156-1:2015 ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 1: REQUIREMENTS FOR APPLICATION DESIGN AND INSTALLATION
UNE-EN 12952-1:2016 Water-tube boilers and auxiliary installations - Part 1: General
DIN EN 12953-12:2004-01 Shell boilers - Part 12: Requirements for grate firing systems for solid fuels for the boiler; German version EN 12953-12:2003
DIN EN 12952-16 E : 2003 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 16: REQUIREMENTS FOR GRATE AND FLUIDIZED BED FIRING SYSTEMS FOR SOLID FUELS FOR THE BOILER
BS EN 746-2:2010 Industrial thermoprocessing equipment Safety requirements for combustion and fuel handling systems
BS EN 12952-1:2015 Water-tube boilers and auxiliary installations General
I.S. EN 746-2:2010 INDUSTRIAL THERMOPROCESSING EQUIPMENT - PART 2: SAFETY REQUIREMENTS FOR COMBUSTION AND FUEL HANDLING SYSTEMS
I.S. EN 12952-16:2002 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 16: REQUIREMENTS FOR GRATE AND FLUIDIZED-BED FIRING SYSTEMS FOR SOLID FUELS FOR THE BOILER
12/30268377 DC : 0 BS EN 50156-2 - ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 2: REQUIREMENTS FOR DESIGN, DEVELOPMENT AND TYPE APPROVAL OF SAFETY DEVICES AND SUBSYSTEMS
14/30294509 DC : 0 BS EN 12952-1 - WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 1: GENERAL
PREN 50156-2 : DRAFT 2012 ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 2: REQUIREMENTS FOR DESIGN, DEVELOPMENT AND TYPE APPROVAL OF SAFETY DEVICES AND SUBSYSTEMS
DIN EN 746-2:2011-02 Industrial thermoprocessing equipment - Part 2: Safety requirements for combustion and fuel handling systems
DIN EN 12952-13 E : 2003 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 13: REQUIREMENTS FOR FLUE GAS CLEANING SYSTEMS
BS EN 12952-16:2002 Water-tube boilers and auxiliary installations Requirements for grate and fluidized-bed firing systems for solid fuels for the boiler
UNE-EN 12952-7:2014 Water-tube boilers and auxiliary installations - Part 7: Requirements for equipment for the boiler
UNI EN 12952-7 : 2013 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 7: REQUIREMENTS FOR EQUIPMENT FOR THE BOILER
UNI EN 746-2 : 2011 INDUSTRIAL THERMOPROCESSING EQUIPMENT - PART 2: SAFETY REQUIREMENTS FOR COMBUSTION AND FUEL HANDLING SYSTEMS
PD CEN/TR 16787:2014 Industrial Gas Installation. Guideline
BS EN 50156-2:2015 Electrical equipment for furnaces and ancillary equipment Requirements for design, development and type approval of safety devices and subsystems
PREN 12952-1 : DRAFT 2014 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 1: GENERAL
DIN EN 12952-16:2003-04 Water-tube boilers and auxiliary installations - Part 16: Requirements for grate and fluidized-bed firing systems for solid fuels for the boiler
BS EN 12952-9:2002 Water-tube boilers and auxiliary installations Requirements for firing systems for pulverized solid fuels for the boiler
BS EN 12952-13:2003 Water-tube boilers and auxiliary installations Requirements for flue gas cleaning systems
BS EN 50156-1:2015 Electrical equipment for furnaces and ancillary equipment Requirements for application design and installation
12/30260546 DC : 0 BS EN 50156-1 - ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 1: REQUIREMENTS FOR APPLICATION DESIGN AND INSTALLATION
EN 746-2:2010 Industrial thermoprocessing equipment - Part 2: Safety requirements for combustion and fuel handling systems
I.S. EN 50156-2:2015 ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 2: REQUIREMENTS FOR DESIGN, DEVELOPMENT AND TYPE APPROVAL OF SAFETY DEVICES AND SUBSYSTEMS
API 538 : 2015 INDUSTRIAL FIRED BOILERS FOR GENERAL REFINERY AND PETROCHEMICAL SERVICE
DIN EN 12952-1:2016-02 WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 1: GENERAL
BS EN 12953-12:2003 Shell boilers Requirements for grate firing systems for solid fuels for the boiler
EN 50156-1:2015 Electrical equipment for furnaces and ancillary equipment - Part 1: Requirements for application design and installation
EN 50156-2:2015 Electrical equipment for furnaces and ancillary equipment - Part 2: Requirements for design, development and type approval of safety devices and subsystems

EN 676:2003+A2:2008/AC:2008 AUTOMATIC FORCED DRAUGHT BURNERS FOR GASEOUS FUELS
EN 13480-2:2017 Metallic industrial piping - Part 2: Materials
EN 751-3:1996/AC:1997 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 3: Unsintered PTFE tapes
EN 264 : 1991 SAFETY SHUT OFF DEVICES FOR COMBUSTION PLANTS USING LIQUID FUELS - SAFETY REQUIREMENTS AND TESTING
ISO 6976:2016 Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition
EN 293:1992 Oil pressure atomizing nozzles - Minimum requirements - Testing
EN 225 : 1987 ATOMIZING OIL BURNERS - PUMPS WITH ROTATING SHAFT & EXTERNAL DRIVE - DIMENSIONS
EN 751-2:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds
PREN 50156-1 : DRAFT 2012 ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 1: REQUIREMENTS FOR APPLICATION DESIGN AND INSTALLATION
ISO 7-2:2000 Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges
EN 161:2011+A3:2013 Automatic shut-off valves for gas burners and gas appliances
EN 267:2009+A1:2011 Automatic forced draught burners for liquid fuels
EN 1044 : 1999 BRAZING - FILLER METALS
EN 12952-1:2015 Water-tube boilers and auxiliary installations - Part 1: General
EN ISO 3677:2016 Filler metal for soldering and brazing - Designation (ISO 3677:2016)
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
ISO 3677:2016 Filler metal for soldering and brazing — Designation
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 230:2005 Automatic burner control systems for oil burners
IEC 60730-2-5:2013+AMD1:2017 CSV Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems
EN 751-1:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds
EN 298:2012 Automatic burner control systems for burners and appliances burning gaseous or liquid fuels
EN 88:1991/A1:1996 PRESSURE GOVERNORS FOR GAS APPLIANCES FOR INLET PRESSURE UP TO 200 MBAR
EN 226:1987/AC1:1987 Atomizing oil burners - Connecting dimensions between burners and heat generators
EN 299:2009 Oil pressure atomizing nozzles - Determination of the angle and spray characteristics
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
EN 12952-5:2011 Water-tube boilers and auxiliary installations - Part 5: Workmanship and construction of pressure parts of the boiler
1997/23/EC : 1997 DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT
EN 287-1:2011 Qualification test of welders - Fusion welding - Part 1: Steels

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.