EN 13617-2:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Petrol filling stations - Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers
09-25-2021
03-14-2012
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Explosion protection measures
5 Construction
6 Physical properties
7 Operational requirements
8 Overview of tests
9 Information for use
Annex A (normative) - General requirements of test
Annex B (normative) - Tests
Annex C (informative) - Environmental aspects
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 94/9/EC
Bibliography
This European Standard specifies safety requirements for the construction and performance of safe breaks to be fitted to metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l min-1.The requirements apply to safe breaks at ambient temperatures from –20 °C to +40 °C with the possibility for an extended temperature range.It pays particular attention to electrical, mechanical and hydraulic characteristics of, and electrical apparatus incorporated within or mounted on, the safe break.This European Standard applies mainly to hazards related to the ignition of liquid fuels being dispensed or their vapour. This European Standard also addresses electrical and mechanical hazards.NOTE 1This European Standard does not apply to equipment for use with liquefied petroleum gas (LPG) or liquefied natural gas (LNG) or compressed natural gas (CNG).NOTE 2Fuels other than of Explosion Group IIA are excluded from this European Standard.
| Committee |
CEN/TC 393
|
| DevelopmentNote |
Supersedes PREN 13617-2. (04/2012)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNI EN 13617-2 : 2012 | Identical |
| SS-EN 13617-2:2012 | Identical |
| BS EN 13617-2:2012 | Identical |
| NS EN 13617-2 : 2012 | Identical |
| DIN EN 13617-2:2018-11 (Draft) | Identical |
| I.S. EN 13617-2:2012 | Identical |
| PN EN 13617-2 : 2012 | Identical |
| UNE-EN 13617-2:2012 | Identical |
| NF EN 13617-2 : 2012 | Identical |
| DIN EN 13617-2:2012-05 | Identical |
| NBN EN 13617-2 : 2012 | Identical |
| SN EN 13617-2 : 2012 | Identical |
| NEN EN 13617-2 : 2012 | Identical |
| ONORM EN 13617-2 : 2012 | Identical |
| 10/30219414 DC : 0 | BS EN 13617-4 - PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS |
| DIN EN 16507:2014-12 | RAILWAY APPLICATIONS - GROUND BASED SERVICE - DIESEL REFUELLING EQUIPMENT |
| PREN 13012 : DRAFT 2010 | PETROL FILLING STATIONS - CONSTRUCTION AND PERFORMANCE OF AUTOMATIC NOZZLES FOR USE ON FUEL DISPENSERS |
| EN 13617-4:2012 | Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers |
| UNE-EN 13617-4:2012 | Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers |
| EN 12285-2 : 2005 | WORKSHOP FABRICATED STEEL TANKS - PART 2: HORIZONTAL CYLINDRICAL SINGLE SKIN AND DOUBLE SKIN TANKS FOR THE ABOVEGROUND STORAGE OF FLAMMABLE AND NON-FLAMMABLE WATER POLLUTING LIQUIDS |
| BS EN 16507:2014 | Railway applications. Ground based service. Diesel refuelling equipment |
| I.S. EN 16507:2014 | RAILWAY APPLICATIONS - GROUND BASED SERVICE - DIESEL REFUELLING EQUIPMENT |
| EN 13012:2012 | Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers |
| DIN EN 12285-2:2005-05 | WORKSHOP FABRICATED STEEL TANKS - PART 2: HORIZONTAL CYLINDRICAL SINGLE SKIN AND DOUBLE SKIN TANKS FOR THE ABOVEGROUND STORAGE OF FLAMMABLE AND NON-FLAMMABLE WATER POLLUTING LIQUIDS |
| DIN EN 13617-4:2012-05 | Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers |
| DIN EN 13617-1:2012-08 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| I.S. EN 13012:2012 | PETROL FILLING STATIONS - CONSTRUCTION AND PERFORMANCE OF AUTOMATIC NOZZLES FOR USE ON FUEL DISPENSERS |
| I.S. EN 13617-4:2012 | PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS |
| I.S. EN 13617-1:2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| DIN EN 16507 E : 2014 | RAILWAY APPLICATIONS - GROUND BASED SERVICE - DIESEL REFUELLING EQUIPMENT |
| 10/30219402 DC : 0 | BS EN 13012 - PETROL FILLING STATIONS - CONSTRUCTION AND PERFORMANCE OF AUTOMATIC NOZZLES FOR USE ON FUEL DISPENSERS |
| PREN 13617-1 : DRAFT 2010 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| UNI EN 16507 : 2014 | RAILWAY APPLICATIONS - GROUND BASED SERVICE - DIESEL REFUELING EQUIPMENT |
| 10/30219405 DC : 0 | BS EN 13617-1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| EEMUA 186 : 2016 | A PRACTITIONER'S HANDBOOK FOR POTENTIALLY EXPLOSIVE ATMOSPHERES |
| BS EN 13617-4:2012 | Petrol filling stations Safety requirements for construction and performance of swivels for use on metering pumps and dispensers |
| BS EN 13012:2012 | Petrol filling stations. Construction and performance of automatic nozzles for use on fuel dispensers |
| UNI EN 13617-1 : 2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| EN 16507:2014 | Railway applications - Ground based service - Diesel refuelling equipment |
| DIN EN 13012:2012-09 | Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers |
| BS EN 13617-1:2012 | Petrol filling stations Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| UNE-EN 13012:2012 | Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers |
| UNE-EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| UNI EN 13617-4 : 2012 | PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS |
| UNI EN 13012 : 2012 | PETROL FILLING STATIONS - CONSTRUCTION AND PERFORMANCE OF AUTOMATIC NOZZLES FOR USE ON FUEL DISPENSERS |
| PREN 13617-4 : DRAFT 2010 | PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS |
| 08/30186475 DC : 0 | BS EN 13617-1 AMD1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| UNE-EN 16507:2015 | Railway applications - Ground based service - Diesel refuelling equipment |
| EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| BS EN 12285-2:2005 | Workshop fabricated steel tanks Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non-flammable water polluting liquids |
| EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| EN 228:2012+A1:2017 | Automotive fuels - Unleaded petrol - Requirements and test methods |
| ISO 1825:2010 | Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling Specification |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| EN 13483:2013 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification |
| EN 13463-1:2009 | Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements |
| EN ISO 8031:2009 | Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2009) |
| ISO 965-2:1998 | ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO 11925-3:1997 | Reaction to fire tests — Ignitability of building products subjected to direct impingement of flame — Part 3: Multi-source test |
| ISO 261:1998 | ISO general purpose metric screw threads General plan |
| EN 13012:2012 | Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers |
| EN 1360:2013 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification |
| PREN 13617-1 : DRAFT 2010 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 8031:2009 | Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity |
| 1994/9/EC : 1994 | DIRECTIVE 94/9/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 23 MARCH 1994 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.