• There are no items in your cart

EN 14303:2015

Current
Current

The latest, up-to-date edition.

Thermal insulation products for building equipment and industrial installations - Factory made mineral wool (MW) products - Specification
Published date

12-09-2015

European foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols, units and abbreviated terms
4 Requirements
5 Test methods
6 Designation code
7 Assessment and Verification of the Constancy of
  Performance (AVCP)
8 Marking and labelling
Annex A (normative) - Factory production control
Annex B (informative) - Additional Properties
Annex ZA (informative) - Clauses of this European Standard
         addressing the provisions of the EU Construction
         Products Regulation
Bibliography

This European Standard specifies the requirements for factory made mineral wool products, which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately 0 °C to + 800 °C.Below an operating temperature of ambient, special means against water vapour diffusion and water accumulation by air flow might be required. Below an operating temperature of - 50 °C, special tests regarding the suitability of the products in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases.The products are manufactured with or without facings or coatings, in the form of rolls, boards, slabs, mats, felts, quilts, wired mats, lamella mats, bevelled lags and pipe sections.This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.Products with a declared thermal conductivity greater than 0,065 W/(m·K) at 10 °C are not covered by this standard.This European Standard does not cover products for in situ insulation (blowing or pouring) or products for the insulation of the building structure.This European Standard does not cover the following acoustical aspects: direct airborne sound insulation and impact noise transmission index.

Committee
CEN/TC 88
DevelopmentNote
Supersedes PREN 14303. (01/2016)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current
Supersedes

Standards Relationship
NF EN 14303 : 2016 Identical
DIN EN 14303 E : 2016 Identical
DIN EN 14303:2016-08 Identical
NBN EN 14303 : 2016 Identical
NEN EN 14303 : 2015 Identical
NS EN 14303 : 2015 Identical
I.S. EN 14303:2015 Identical
PN EN 14303 : 2016 Identical
SN EN 14303 : 2015 Identical
UNI EN 14303 : 2013 Identical
UNI EN 14303:2016 Identical
SS-EN 14303:2015 Identical
UNE-EN 14303:2017 Identical
BS EN 14303 : 2009 Identical
BS EN 14303:2015 Identical

12/30256790 DC : 0 BS EN 14706 - THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF MAXIMUM SERVICE TEMPERATURE
UNE-EN 16783:2017 Thermal insulation products - Product category rules (PCR) for factory made and in-situ formed products for preparing environmental product declarations
BS EN 13168 : 2012 THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD WOOL (WW) PRODUCTS - SPECIFICATION
I.S. EN 13168:2012 THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD WOOL (WW) PRODUCTS - SPECIFICATION
EN 13162:2012+A1:2015 Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification
UNI EN 15715 : 2009 THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS
DIN EN 13168:2015-04 THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD WOOL (WW) PRODUCTS - SPECIFICATION
DIN EN 13162:2015-04 THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION
DIN EN 14706:2013-01 Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature
BS EN 14706:2012 Thermal insulating products for building equipment and industrial installations. Determination of maximum service temperature
I.S. EN 14706:2012 THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF MAXIMUM SERVICE TEMPERATURE
I.S. EN 13162:2012 THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION
VDI 2055 Blatt 2:2013-10 Thermal insulation of heated and refrigerated operational installations in the industry and in the building services - Technical basics for the verification of properties of insulating materials
14/30301580 DC : 0 BS EN/TC 16783 - THERMAL INSULATION PRODUCTS - PRODUCT CATEGORY RULES (PCR) FOR FACTORY MADE AND IN-SITU FORMED PRODUCTS FOR PREPARING ENVIRONMENTAL PRODUCT DECLARATIONS
BS ISO 18097:2013 Thermal insulating products for building equipment and industrial installations. Determination of maximum service temperature
DIN EN 15715:2010-04 Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products
PREN 13162 : DRAFT 2010 THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION
I.S. EN 16783:2017 THERMAL INSULATION PRODUCTS - PRODUCT CATEGORY RULES (PCR) FOR FACTORY MADE AND IN-SITU FORMED PRODUCTS FOR PREPARING ENVIRONMENTAL PRODUCT DECLARATIONS
I.S. EN 15715:2009 THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS
UNI EN 14706 : 2012 THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF MAXIMUM SERVICE TEMPERATURE
10/30213959 DC : 0 BS EN 13162 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION
UNE-EN 15715:2012 Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products
16/30344387 DC : 0 BS EN 16475-1 - CHIMNEYS - ACCESSORIES - PART 1: CHIMNEY SILENCERS - REQUIREMENTS AND TEST METHODS
ISO 18097:2013 Thermal insulating products for building equipment and industrial installations — Determination of maximum service temperature
DIN EN 14706 E : 2013 THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF MAXIMUM SERVICE TEMPERATURE
BS EN 13162 : 2012 THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION
UNE-EN 13162:2013 Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification
UNE-EN 13168:2013 Thermal insulation products for buildings - Factory made wood wool (WW) products - Specification
EN 13168:2012+A1:2015 Thermal insulation products for buildings - Factory made wood wool (WW) products - Specification
EN 16783:2017 Thermal insulation products - Product category rules (PCR) for factory made and in-situ formed products for preparing environmental product declarations
EN 14706:2012 Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature
EN 15715:2009 Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products
BS EN 16783:2017 Thermal insulation products. Product category rules (PCR) for factory made and in-situ formed products for preparing environmental product declarations
PREN 14706 : DRAFT 2012 THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF MAXIMUM SERVICE TEMPERATURE
BS EN 15715:2009 Thermal insulation products. Instructions for mounting and fixing for reaction to fire testing. Factory made products
DIN EN 15715 E : 2010 THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS
UNE-EN 13162:2013+A1:2015 Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification

ISO 9229:2007 Thermal insulation Vocabulary
EN 12667:2001 Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance
ISO 13787:2003 Thermal insulation products for building equipment and industrial installations Determination of declared thermal conductivity
EN 14706:2012 Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature
EN ISO 23993:2010 Thermal insulation products for building equipment and industrial installations - Determination of design thermal conductivity (ISO 23993:2008, Corrected version 2009-10-01)
EN 13468:2001 Thermal insulating products for building equipment and industrial installations - Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH
EN ISO 10456:2007/AC:2009 BUILDING MATERIALS AND PRODUCTS - HYGROTHERMAL PROPERTIES - TABULATED DESIGN VALUES AND PROCEDURES FOR DETERMINING DECLARED AND DESIGN THERMAL VALUES
ISO 354:2003 Acoustics — Measurement of sound absorption in a reverberation room
EN 13820:2003 Thermal insulating materials for building applications - Determination of organic content
EN 29052-1:1992 Acoustics - Determination of dynamic stiffness - Part 1: Materials used under floating floors in dwellings
EN 12939:2000 Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Thick products of high and medium thermal resistance
EN ISO 8497:1996 Thermal insulation - Determination of steady-state thermal transmission properties of thermal insulation for circular pipes (ISO 8497:1994)
ISO 1716:2010 Reaction to fire tests for products Determination of the gross heat of combustion (calorific value)
EN ISO 9229:2007 Thermal insulation - Vocabulary (ISO 9229:2007)
305/2011 : 2011 AMD 2 2014 REGULATION (EU) NO 305/2011 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 9 MARCH 2011 LAYING DOWN HARMONISED CONDITIONS FOR THE MARKETING OF CONSTRUCTION PRODUCTS AND REPEALING COUNCIL DIRECTIVE 89/106/EEC (TEXT WITH EEA RELEVANCE)
EN 13469:2012 Thermal insulating products for building equipment and industrial installations - Determination of water vapour transmission properties of preformed pipe insulation
ISO 23993:2008 Thermal insulation products for building equipment and industrial installations — Determination of design thermal conductivity
EN 824:2013 Thermal insulating products for building applications - Determination of squareness
ISO 11925-2:2010 Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test
EN ISO 1182:2010 Reaction to fire tests for products - Non-combustibility test (ISO 1182:2010)
EN 825:2013 Thermal insulating products for building applications - Determination of flatness
ISO 9053:1991 Acoustics Materials for acoustical applications Determination of airflow resistance
EN 823:2013 Thermal insulating products for building applications - Determination of thickness
ISO 8497:1994 Thermal insulation — Determination of steady-state thermal transmission properties of thermal insulation for circular pipes
EN ISO 13787:2003 Thermal insulation products for building equipment and industrial installations - Determination of declared thermal conductivity (ISO 13787:2003)
EN 13470:2001 Thermal insulating products for building equipment and industrial installations - Determination of the apparent density of preformed pipe insulation
EN 13238:2010 Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates
ISO 1182:2010 Reaction to fire tests for products Non-combustibility test
EN 13823:2010+A1:2014 REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - BUILDING PRODUCTS EXCLUDING FLOORINGS EXPOSED TO THE THERMAL ATTACK BY A SINGLE BURNING ITEM
EN 1602:2013 Thermal insulating products for building applications - Determination of the apparent density
EN 29053:1993 Acoustics - Materials for acoustical applications - Determination of airflow resistance (ISO 9053:1991)
ISO 11654:1997 Acoustics — Sound absorbers for use in buildings — Rating of sound absorption
EN 13472:2012 Thermal insulating products for building equipment and industrial installations - Determination of short term water absorption by partial immersion of preformed pipe insulation
EN 13162:2012+A1:2015 Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification
EN 1604:2013 Thermal insulating products for building applications - Determination of dimensional stability under specified temperature and humidity conditions
EN ISO 354:2003 Acoustics - Measurement of sound absorption in a reverberation room (ISO 354:2003)
EN 14707:2012 Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature for preformed pipe insulation
ISO 10456:2007 Building materials and products — Hygrothermal properties — Tabulated design values and procedures for determining declared and design thermal values
ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1
EN 1609:2013 Thermal insulating products for building applications - Determination of short term water absorption by partial immersion
EN 826:2013 Thermal insulating products for building applications - Determination of compression behaviour
EN ISO 1716:2010 Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716:2010)
EN ISO 11654:1997 Acoustics - Sound absorbers for use in buildings - Rating of sound absorption (ISO 11654:1997)
EN 15715:2009 Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products
EN ISO 11925-2:2010/AC:2011 REACTION TO FIRE TESTS - IGNITABILITY OF PRODUCTS SUBJECTED TO DIRECT IMPINGEMENT OF FLAME - PART 2: SINGLE-FLAME SOURCE TEST
EN 12086:2013 Thermal insulating products for building applications - Determination of water vapour transmission properties
EN 13172:2012 Thermal insulation products - Evaluation of conformity
EN 822:2013 Thermal insulating products for building applications - Determination of length and width

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.