EN 14753:2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Safety of machinery - Safety requirements for machinery and equipment for continuous casting of steel
03-14-2022
12-12-2007
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
5.1 General
5.1.1 Introduction
5.1.2 CCM-arrangement, site inspection
5.1.3 Safety layout
5.1.4 Safety devices
5.1.5 Hydraulic, pneumatic, gas, cooling
and lubrication systems
5.1.6 Fluid systems carrying or containing fluids
5.1.7 Fluids to be discharged to drains
5.1.8 Personal protective equipment
5.1.9 Warning devices and safety signs
5.1.10 Access
5.1.11 Escape ways
5.1.12 Electrical equipment
5.1.13 Safety control system
5.1.14 Surface temperatures and heat radiation
5.1.15 Ergonomic principles
5.1.16 Fire protection
5.1.17 Operating positions of the CCM
5.1.18 Movable control box
5.1.19 Loss of energy
5.1.20 Harmful areas
5.1.21 Cooling water systems
5.1.22 Radioactive sources
5.1.23 Ladle/tundish emergency systems
5.1.24 Shroud manipulators
5.1.25 Cooling chamber
5.2 List of significant hazards, hazardous situations, safety
requirements and/or measures
5.2.1 General
5.2.2 General
5.2.3 Casting platform
5.2.4 Casting machine equipment
5.2.5 Cutting systems
5.2.6 Run-out (discharge) area
5.3 Special safety requirements or measures
5.3.1 General
5.3.2 Hold-to-run control device
5.3.3 Mechanical restraint devices
5.3.4 Accessible rotating/moving parts
5.4 Noise reduction as a safety requirement
5.4.1 Noise sources
5.4.2 Noise reduction at source by design
5.4.3 Noise reduction by protective measures
5.4.4 Noise reduction by information
6 Verification of the safety requirements and/or measures
7 Information for use
7.1 Signs and warning devices
7.2 Accompanying documents
7.2.1 Instruction handbook
7.2.2 Machine/equipment declaration
7.2.3 Instruction for transport, setting
up/installation
7.2.4 Information about commissioning and
dismantling
7.2.5 Operation instructions concerning
the equipment
7.2.6 Maintenance manual
7.3 Minimum marking
7.4 Training of personnel
Annex A (normative) - Safety requirements and/or
measures for electrical equipment
and controls
A.1 General
A.2 Special requirements for controls
A.3 Special requirements for shut-down equipment
A.3.1 Stop and emergency-off functions
A.3.2 Emergency stops
A.3.3 Emergency stop functions
A.3.4 Emergency stop assigned to areas
Annex B (normative) - Equipment of a CCM covered by
this standard
B.1 Casting platform
B.2 Casting machine equipment
B.3 Cutting area
B.4 Run-out (discharge) area
B.5 General equipment
Annex C (normative) - Noise test code
C.1 Introduction
C.2 Determination of sound power level
C.3 Determination of emission sound pressure
levels
C.3.1 Determination of the emission sound
pressure level at specified measuring
points
C.3.2 Determination of emission sound pressure
level at work stations
C.4 Measurement uncertainty
C.5 Operating conditions
C.6 Information to be recorded and reported
C.7 Declaration and verification of noise
emission values
Annex ZA (informative) - Relationship between this
European Standard and the
Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) - Relationship between this
European Standard and the
Essential Requirements of EU
Directive 2006/42/EC
Bibliography
This European Standard applies for plant (containing machinery and equipment) used in the process of continuous casting of liquid steel (hereafter referred to as continuous casting machine, CCM) as defined in 3.1 and illustrated in Annex B.This European Standard deals with all significant hazards, hazardous situations and events relevant to machinery and equipment for the continuous casting of steel, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).This European Standard specifies the safety requirements to be met during design, assembly, transport, commissioning, operation, maintenance (as described in Clause 5) and decommissioning of the equipment.This European Standard assumes that the machinery and equipment of the plant is operated and maintained by adequately trained and competent personnel (see 7.4). Manual intervention for setting, adjustment and maintenance is accepted as part of the intended use of the plant.This European Standard assumes that the machinery is used with adequate workplace lighting conforming to EN 12464-1.NOTELocal regulations regarding lighting should be considered and could differ from requirements of EN 12464-1.This European Standard applies to:CCM for the transformation of molten liquid steel into solid products in sections (e.g. square, rectangular, beam blank, circular)from the point where overhead cranes or other transport systems deposit ladles (e.g. in a ladle turret or ladle car);via casting process;via cutting equipment;to the run-out-area where the cut product is collected.This European Standard does not cover safety requirements for:auxiliary plants (e.g. water treatment, refractory handling);ladles;cranes; winches and hoists;conveyors or handling systems.This European Standard is not applicable to CCM, manufactured before the date of publication of this standard by CEN.
| Committee |
CEN/TC 322
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ONORM EN 14753 : 2008 | Identical |
| NS EN 14753 : 1ED 2007 | Identical |
| I.S. EN 14753:2007 | Identical |
| NBN EN 14753 : 2008 | Identical |
| UNE-EN 14753:2008 | Identical |
| DIN EN 14753 E : 2008 | Identical |
| PN EN 14753 : 2010 | Identical |
| NEN EN 14753 : 2008 | Identical |
| NF EN 14753 : 2008 | Identical |
| DIN EN 14753:2008-03 | Identical |
| UNI EN 14753 : 2008 | Identical |
| SN EN 14753 : 2008 | Identical |
| BS EN 14753:2007 | Identical |
| DIN EN 15093:2009-06 | Safety of machinery - Safety requirements for hot flat rolling mills |
| BS EN 15093:2008 | Safety of machinery. Safety requirements for hot flat rolling mills |
| I.S. EN 15093:2008 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR HOT FLAT ROLLING MILLS |
| DIN EN 15949:2012-05 | Safety of machinery - Safety requirements for bar mills, structural steel mills and wire rod mills |
| UNI EN 15093 : 2009 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR HOT FLAT ROLLING MILLS |
| 09/30201995 DC : 0 | BS EN 15949 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR BAR MILLS, STRUCTURAL STEEL MILLS AND WIRE ROD MILLS |
| UNI EN 15949 : 2012 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR BAR MILLS, STRUCTURAL STEEL MILLS AND WIRE ROD MILLS |
| I.S. EN 15949:2012 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR BAR MILLS, STRUCTURAL STEEL MILLS AND WIRE ROD MILLS |
| BS EN 15949:2012 | Safety of machinery. Safety requirements for bar mills, structural steel mills and wire rod mills |
| DIN EN 15093 E : 2009 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR HOT FLAT ROLLING MILLS |
| EN 15949:2012 | Safety of machinery - Safety requirements for bar mills, structural steel mills and wire rod mills |
| EN 15093:2008 | Safety of Machinery - Safety requirements for hot flat rolling mills |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 12464-1:2011 | Light and lighting - Lighting of work places - Part 1: Indoor work places |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
| PREN 15004-1 : DRAFT 2016 | FIXED FIREFIGHTING SYSTEMS - GAS EXTINGUISHING SYSTEMS - PART 1: DESIGN, INSTALLATION AND MAINTENANCE (ISO 14520-1:2015, MODIFIED) |
| ISO 14122-1:2016 | Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN 981:1996+A1:2008 | Safety of machinery - System of auditory and visual danger and information signals |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| EN 61310-2:2008 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN 12094-1:2003 | Fixed firefighting systems - Components for gas extinguishing systems - Part 1: Requirements and test methods for electrical automatic control and delay devices |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| EN 614-2:2000+A1:2008 | Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks |
| EN 1837:1999+A1:2009 | Safety of machinery - Integral lighting of machines |
| EN 811 : 1996 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE LOWER LIMBS |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| EN 13478:2001+A1:2008 | Safety of machinery - Fire prevention and protection |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| EN ISO 7731:2008 | Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003) |
| EN ISO 11820 : 1996 | ACOUSTICS - MEASUREMENTS ON SILENCERS IN SITU |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN ISO 11688-2 : 2000 | ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN |
| ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
| ISO 7731:2003 | Ergonomics Danger signals for public and work areas Auditory danger signals |
| EN 574:1996+A1:2008 | Safety of machinery - Two-hand control devices - Functional aspects - Principles for design |
| EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
| ISO 11820:1996 | Acoustics — Measurements on silencers in situ |
| EN 626-2:1996+A1:2008 | Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures |
| IEC 60405:2003 | Nuclear instrumentation - Constructional requirements and classification of radiometric gauges |
| EN ISO 12100-1:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY |
| EN ISO 14122-3:2016 | Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 842:1996+A1:2008 | Safety of machinery - Visual danger signals - General requirements, design and testing |
| EN ISO 14122-4:2016 | Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016) |
| EN ISO 14122-2:2016 | Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016) |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| EN ISO 12100-2:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES |
| EN ISO 6682:2008 | Earth-moving machinery - Zones of comfort and reach for controls (ISO 6682:1986, including Amd 1:1989) |
| ISO 14520-1:2015 | Gaseous fire-extinguishing systems — Physical properties and system design — Part 1: General requirements |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| ISO 11064-1:2000 | Ergonomic design of control centres Part 1: Principles for the design of control centres |
| EN ISO 6743-4:2015 | Lubricants, industrial oils and related products (class L) - Classification - Part 4: Family H (Hydraulic systems) (ISO 6743-4:2015) |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| ISO 11546-1:1995 | Acoustics Determination of sound insulation performances of enclosures Part 1: Measurements under laboratory conditions (for declaration purposes) |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 50171 : 2001 COR 2001 | CENTRAL POWER SUPPLY SYSTEMS |
| EN 626-1:1994+A1:2008 | Safety of machinery - Reduction of risks to health from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers |
| EN ISO 11064-1:2000 | Ergonomic design of control centres - Part 1: Principles for the design of control centres (ISO 11064-1:2000) |
| EN ISO 11691:2009 | Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995) |
| EN ISO 11821 : 1997 | ACOUSTICS - MEASUREMENT OF THE IN SITU SOUND ATTENUATION OF A REMOVABLE SCREEN |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| EN ISO 11546-1:2009 | Acoustics - Determination of sound insulation performances of enclosures - Part 1: Measurements under laboratory conditions (for declaration purposes) (ISO 11546-1:1995) |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| EN ISO 14122-1:2016 | Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| ISO 11691:1995 | Acoustics Measurement of insertion loss of ducted silencers without flow Laboratory survey method |
| ISO 6743-4:2015 | Lubricants, industrial oils and related products (class L) Classification Part 4: Family H (Hydraulic systems) |
| ISO 7745:2010 | Hydraulic fluid power — Fire-resistant (FR) fluids — Requirements and guidelines for use |
| ISO 11821:1997 | Acoustics — Measurement of the in situ sound attenuation of a removable screen |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.