• There are no items in your cart

EN 15512:2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Steel static storage systems - Adjustable pallet racking systems - Principles for structural design
Superseded date

12-07-2020

Published date

03-18-2009

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Basis of design
6 Actions and combinations of actions
7 Partial factors and combination rules
8 Steel
9 Structural analysis
10 Global analysis of beam pallet racks
11 Serviceability limit states
12 Marking and labelling
13 Test methods and evaluation of results
Annex A (normative) - Testing
Annex B (informative) - Amplified sway method for down-aisle
                        stability analysis
Annex C (informative) - Approximate equations for the design
                        of a regular storage rack in the
                        down-aisle direction
Annex D (informative) - Background to the acceptance of
                        materials of low f[u]/f[y] ratio
                        (cold reduced steel)
Annex E (informative) - Position inaccuracies
Annex F (informative) - Equivalent beam loads
Annex G (informative) - Simplified method for cross-aisle
                        stability analysis in circumstances
                        where there is uniform distribution
                        of compartment loads over the
                        height of the upright frame
Annex H (informative) - Factory production control (FPC)
Annex I (informative) - A-deviations
Bibliography

This European Standard specifies the structural design requirements applicable to all types of adjustable beam pallet rack systems fabricated from steel members intended for the storage of unit loads and subject to predominantly static loads. Both un-braced and braced systems are included.This European Standard gives guidelines for the design of clad rack buildings where requirements are not covered in EN 1993. The requirements of this European Standard also apply to ancillary structures, where rack components are employed as the main structural members. This European Standard does not cover other generic types of storage structures. Specifically, this European Standard does not apply to mobile storage systems, drive-in, drive-through and cantilever racks or static steel shelving systems, nor does this European Standard establish specific design rules for the assessment of racking in seismic areas.

Committee
CEN/TC 344
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

14/30288566 DC : 0 BS EN 16681 - STEEL STATIC STORAGE SYSTEMS - ADJUSTABLE PALLET RACKING SYSTEMS - PRINCIPLES FOR SEISMIC DESIGN
BS EN 16681:2016 Steel static storage systems. Adjustable pallet racking systems. Principles for seismic design
UNE-EN 16681:2016 Steel static storage systems - Adjustable pallet racking systems - Principles for seismic design
S.R. CWA 16688:2013 BATTERY SWAP SYSTEMS INTERFACES FOR ELECTRIC VEHICLES
I.S. EN 16681:2016 STEEL STATIC STORAGE SYSTEMS - ADJUSTABLE PALLET RACKING SYSTEMS - PRINCIPLES FOR SEISMIC DESIGN
CSA S16 : 2014 DESIGN OF STEEL STRUCTURES
EN 16681:2016 Steel static storage systems - Adjustable pallet racking systems - Principles for seismic design
UNE-EN 15635:2010 Steel static storage systems - Application and maintenance of storage equipment

EN 10002-1 : 2001 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
EN 10162:2003 Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances
EN 15635:2008 Steel static storage systems - Application and maintenance of storage equipment
EN 528:2008 Rail dependent storage and retrieval equipment - Safety requirements
EN 10326:2004 Continuously hot-dip coated strip and sheet of structural steels - Technical delivery conditions
EN 15629:2008 Steel static storage systems - Specification of storage equipment
ISO 7438:2016 Metallic materials Bend test
PREN 15878 : DRAFT 2008 STEEL STATIC STORAGE SYSTEMS - ADJUSTABLE PALLET RACKING - TERMS AND DEFINITIONS
EN 10143:2006 (edition 2) Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 1991-1-1:2002/AC:2009 EUROCODE 1: ACTIONS ON STRUCTURES - PART 1-1: GENERAL ACTIONS - DENSITIES, SELF-WEIGHT, IMPOSED LOADS FOR BUILDINGS
ISO 9001:2015 Quality management systems — Requirements
EN 1993-1-3:2006/AC:2009 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-3: GENERAL RULES - SUPPLEMENTARY RULES FOR COLD-FORMED MEMBERS AND SHEETING
EN 15620:2008 Steel static storage systems - Adjustable pallet racking - Tolerances, deformations and clearances
EN 1990:2002/A1:2005/AC:2010 EUROCODE - BASIS OF STRUCTURAL DESIGN
EN 1993-1-1:2005/A1:2014 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
EN ISO 7438:2016 Metallic materials - Bend test (ISO 7438:2016)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.