• There are no items in your cart

EN 16719:2018

Current
Current

The latest, up-to-date edition.

Transport platforms
Published date

02-28-2018

European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or measures
6 Verification
7 User information
Annex A (normative) - European storm wind map
Annex B (normative) - Performance levels for safety devices
Annex C (informative) - Limit state proof of static strength
Annex ZA (informative) - Relationship between this European
         Standard and the essential requirements of
         Directive 2006/42/EC aimed to be covered
Bibliography

1.1Temporarily-installed, guided powered platforms with rack and pinion drive, which have an open carrier and hold-to-run controls operated by authorized, trained operators on the carrier. Used for transporting authorised passengers and materials vertically (or along the path 15° maximum of the vertical), at limited speed (max 0,2 m/s), with a minimum offset distance of 500 mm and serving fixed levels on a building or structure for construction related activities including renovation and maintenance. This European Standard does not includea)hydraulic drives for transport platforms,b)wire rope drives for transport platforms,c)chain drives for transport platforms,d)use as a Mast Climbing Work Platform (see EN 1495),e)use as a Goods Hoist (see EN 12158-1),f)use as a Passenger/Goods Hoist (see EN 12159).1.2This European Standard identifies hazards as listed in Clause 4 which arise during the various phases in the life of such equipment and describes methods for the elimination or reduction of these hazards when used as intended by the manufacturer.1.3This European Standard does not specify the additional requirements fora)operation in severe conditions (e.g. extreme climates, strong magnetic fields),b)lightning protection,c)operation subject to special rules (e.g. potentially explosive atmospheres),d)electromagnetic compatibility (emission, immunity),e) handling of loads the nature of which could lead to dangerous situations (e.g. molten metal, acids/bases,f)radiating materials, fragile loads),g)the use of combustion engines,h)the use of remote controls,i)hazards occurring during manufacture,j)hazards occurring as a result of mobility,k)hazards occurring as a result of being erected over a public road,l)earthquakes,m)noise. 1.4This European Standard is not applicable toa)builders hoists for materials,b)builders hoists for persons and materials,c)lifts according to EN 81-1:1998, EN 81-2:1998 and EN 81-3:2000,d) inclined hoists according to EN 12158-2:2000,e)work cages suspended from lifting appliances,f)work platforms carried on the forks of fork trucks,g)work platforms,h)funiculars,i)lifts specially designed for military purposes,j)mine lifts,k)theatre elevators,l)special purpose lifts.1.5This European Standard deals with the transport platform installation. It includes the base frame and base enclosure but excludes the design of any concrete, hard core, timber or other foundation arrangement. It includes the design of mast ties but excludes the design of anchorage bolts to the supporting structure. It includes the landing gates and their frames but excludes the design of any anchorage fixing bolts to the supporting structure.

Committee
CEN/TC 10
DevelopmentNote
Supersedes PREN 16719. (03/2018)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

Standards Relationship
I.S. EN 16719:2018 Identical
NF EN 16719 February 2018 Identical
NS EN 16719 : 2018 Identical
UNE-EN 16719:2018 Identical
ÖNORM EN 16719: 2019 01 01 Identical
PN EN 16719:2018 Identical
SN EN 16719 : 2018 Identical
UNI EN 16719 : 2018 Identical
BS EN 16719:2018 Identical
SS-EN 16719:2018 Identical
NEN EN 16719 : 2018 Identical
DIN EN 16719:2019-06 Identical

ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
EN 1037:1995+A1:2008 Safety of machinery - Prevention of unexpected start-up
ISO 14119:2013 Safety of machinery Interlocking devices associated with guards Principles for design and selection
ISO 4302:2016 Cranes Wind load assessment
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
ISO 6336-2:2006 Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting)
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
EN 1999-1-1:2007/A2:2013 EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
ISO 6336-3:2006 Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength
EN 12158-1:2000+A1:2010 Builders' hoists for goods - Part 1: Hoists with accessible platforms
EN ISO 7731:2008 Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003)
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
EN 12158-2:2000+A1:2010 Builders' hoists for goods - Part 2: Inclined hoists with non-accessible load carrying devices
EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 7731:2003 Ergonomics Danger signals for public and work areas Auditory danger signals
ISO 6336-5:2016 Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials
EN 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
EN 13001-2:2014 Crane safety - General design - Part 2: Load actions
EN 60947-4-1 : 2010 AMD 1 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012)
ISO 13849-2:2012 Safety of machinery — Safety-related parts of control systems — Part 2: Validation
EN 12159:2012 Builders hoists for persons and materials with vertically guided cages
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
EN ISO 14119:2013 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection (ISO 14119:2013)
ISO 6336-1:2006 Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
EN ISO 13849-2:2012 Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012)
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
EN 1495:1997+A2:2009/AC:2010 LIFTING PLATFORMS - MAST CLIMBING WORK PLATFORMS
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN 81-22:2014 Safety rules for the construction and installation of lifts - Lifts for the transport of persons and goods - Part 22: Electric lifts with inclined path
EN 1991-1-4:2005/A1:2010 EUROCODE 1: ACTIONS ON STRUCTURES - PART 1-4: GENERAL ACTIONS - WIND ACTIONS
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
EN 81-50:2014 Safety rules for the construction and installation of lifts - Examinations and tests - Part 50: Design rules, calculations, examinations and tests of lift components
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
EN 81-3:2000+A1:2008/AC:2009 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - PART 3: ELECTRIC AND HYDRAULIC SERVICE LIFTS
EN 894-1:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.