• There are no items in your cart

EN 197-1:2011

Current
Current

The latest, up-to-date edition.

Cement - Part 1: Composition, specifications and conformity criteria for common cements
Published date

09-14-2011

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Cement
5 Constituents
6 Composition and notation
7 Mechanical, physical, chemical and durability requirements
8 Standard designation
9 Conformity criteria
Annex A (informative) - List of common cements considered as
        sulfate resisting by National Standards in different
        CEN member countries but not included in Table 2 or
        not fulfilling the requirements given in Table 5
Annex ZA (informative) - Clauses of this European standard
         addressing the provisions of the EU Construction
         Products Directive
Bibliography

This European Standard defines and gives the specifications of 27 distinct common cements, 7 sulfate resisting common cements as well as 3 distinct low early strength blast furnace cements and 2 sulfate resisting low early strength blast furnace cements and their constituents. The definition of each cement includes the proportions in which the constituents are to be combined to produce these distinct products in a range of nine strength classes. The definition also includes requirements which the constituents have to meet. It also includes mechanical, physical, and chemical requirements. Furthermore, this standard states the conformity criteria and the related rules. Necessary durability requirements are also given.In addition to those sulfate resisting cements defined in the present document, other cements conforming either to this standard or to other standards, European or national, have been nationally demonstrated to have sulfate resisting properties. These cements which are listed in Annex A, are considered by different CEN Member countries as sulfate resisting within the limits of their territory.NOTE 1In addition to the specified requirements, an exchange of additional information between the cement manufacturer and user can be helpful. The procedures for such an exchange are not within the scope of this standard but should be dealt with in accordance with national standards or regulations or can be agreed between the parties concerned.NOTE 2The word "cement" in EN 197-1 is used to refer only to common cements unless otherwise specified.This European Standard does not cover:-very low heat special cement covered by EN 14216;-supersulfated cement covered by EN 15743;-calcium aluminate cement covered by EN 14647;masonry cement covered by EN 413-1.

DevelopmentNote
Supersedes ENV 197-1. (09/2000) Supersedes EN 197-4. (09/2011)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current
Supersedes

DIN EN 15191 E : 2010 PRECAST CONCRETE PRODUCTS - CLASSIFICATION OF GLASSFIBRE REINFORCED CONCRETE PERFORMANCE
07/30164091 DC : 0 BS ISO 863 - METHODS OF TESTING CEMENTS - POZZOLANICITY TEST FOR POZZOLANIC CEMENTS
PD CR 14245:2001 Guidelines for the application of EN 197-2. Conformity Evaluation
08/30192726 DC : 0 BS EN 1538 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - DIAPHRAGM WALLS
CEN/TR 16912:2016 Guidelines for a procedure to support the European standardization of cements
13/30277486 DC : 0 BS EN 16572 - CONSERVATION OF CULTURAL HERITAGE - GLOSSARY OF TECHNICAL TERMS CONCERNING MORTARS FOR MASONRY, RENDERS AND PLASTERS USED IN CULTURAL HERITAGE
14/30314735 DC : 0 BS EN 12004-2 - ADHESIVES FOR TILES - PART 2: TEST METHODS
03/310141 DC : DRAFT AUG 2003 EN 14754-1 - CURING COMPOUNDS - TEST METHODS - PART 1: DETERMINATION OF WATER RETENTION EFFICIENCY OF COMMON CURING COMPOUNDS
07/30166977 DC : DRAFT AUG 2007 BS EN 1744-1 - TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 1: CHEMICAL ANALYSIS
PD CR 13933:2000 Masonry cement. Testing for workability (cohesivity)
10/30233182 DC : 0 BS EN 492 - FIBRE-CEMENT SLATES AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS
BS EN 19694-3:2016 Stationary source emissions. Determination of greenhouse gas (GHG) emissions in energy-intensive industries Cement industry
PD CEN/TR 15678:2008 Concrete. Release of regulated dangerous substances into soil, groundwater and surface water. Test method for new or unapproved constituents of concrete and for production concretes
PREN 14199 : DRAFT 2013 EXECUTION OF SPECIAL GEOTECHNICAL WORK - MICROPILES
14/30310830 DC : 0 BS EN 1536:2010/A1 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - BORED PILES
12/30256100 DC : 0 BS EN 12878 - PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
I.S. EN 480-15:2013 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 15: REFERENCE CONCRETE AND METHOD FOR TESTING VISCOSITY MODIFYING ADMIXTURES
S.R. CEN/TR 15840:2009 EVALUATION OF CONFORMITY OF FLY ASH FOR CONCRETE - GUIDELINES FOR THE APPLICATION OF EN 450-2
DIN V 18152:2003-10 LIGHTWEIGHT CONCRETE SOLID BRICKS AND BLOCKS
10/30233189 DC : 0 BS EN 494 - FIBRE-CEMENT PROFILED SHEETS AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS
BS EN 12004-2:2017 Adhesives for ceramic tiles Test methods
07/30165786 DC : DRAFT AUG 2007 BS EN 1367-4 - TESTS FOR THERMAL AND WEATHERING PROPERTIES OF AGGREGATES - PART 4: DETERMINATION OF DRYING SHRINKAGE
13/30280743 DC : 0 BS EN 14199 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - MICROPILES
PREN 1536 : DRAFT 2008 EXECUTION OF SPECIAL GEOTECHNICAL WORK - BORED PILES
UNE-EN ISO 21809-5:2018 Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 5: External concrete coatings (ISO 21809-5:2017)
DIN EN 15422:2008-06 Precast concrete products - Specification of glassfibres for reinforcement of mortars and concretes
DIN EN 13282-2:2015-07 HYDRAULIC ROAD BINDERS - PART 2: NORMAL HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
03/319412 DC : DRAFT NOV 2003 EN 12878 - PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
S.R. CEN/TR 16443:2013 BACKGROUNDS TO THE REVISION OF EN 450-1:2005+A1:2007 - FLY ASH FOR CONCRETE
10/30212126 DC : 0 BS EN 845-2 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS
BS EN 15422:2008 Precast concrete products. Specification of glassfibres for reinforcement of mortars and concretes
BS EN 14490:2010 Execution of special geotechnical works. Soil nailing
06/30153191 DC : 0 BS EN 15542 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
15/30311094 DC : 0 BS EN 13139 - AGGREGATES FOR MORTAR
UNE-EN 15191:2011 Precast concrete products - Classification of glassfibre reinforced concrete performance
PREN 13282-1 : DRAFT 2010 HYDRAULIC ROAD BINDERS - PART 1: RAPID HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
BS ISO 13640:1999 Building construction. Jointing products. Specifications for test substrates
PREN 1766 : DRAFT 2015 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - REFERENCE CONCRETES FOR TESTING
I.S. EN 15743:2010 SUPERSULFATED CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
I.S. EN ISO 21809-5:2017 PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 5: EXTERNAL CONCRETE COATINGS (ISO 21809-5:2017)
BS EN 15368 : 2008 HYDRAULIC BINDER FOR NON-STRUCTURAL APPLICATIONS - DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
BS EN 206 : 2013 CONCRETE - SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
I.S. EN 12467:2012 FIBRE-CEMENT FLAT SHEETS - PRODUCT SPECIFICATION AND TEST METHODS
PREN 13914-1 : DRAFT 2013 DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING
15/30324901 DC : 0 BS EN 1504-3 - PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND AVCP - PART 3: REPAIR CONCRETE AND MORTARS
S.R. CEN/TR 16563:2013 PRINCIPLES OF THE EQUIVALENT DURABILITY PROCEDURE
UNI EN 196-6 : 2010 METHODS OF TESTING CEMENT - PART 6: DETERMINATION OF FINENESS
EN 545:2010 Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
DIN EN 14227-5:2013-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 5: HYDRAULIC ROAD BINDER BOUND GRANULAR MIXTURES
DIN EN 13863-4:2012-07 Concrete pavements - Part 4: Test methods for the determination of wear resistance of concrete pavements to studded tyres; German version EN 13863-4:2012
DIN EN 14216 E : 2015 CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR VERY LOW HEAT SPECIAL CEMENTS
DIN EN 14227-3:2013-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 3: FLY ASH BOUND GRANULAR MIXTURES
DIN EN 13748-2:2005-03 Terrazzo tiles - Part 2: Terrazzo tiles for external use; German version EN 13748-2:2004
DIN EN 196-8:2010-07 Methods of testing cement - Part 8: Heat of hydration - Solution method
BS EN 13286-49:2004 Unbound and hydraulically bound mixtures Accelerated swelling test for soil treated by lime and/or hydraulic binder
BS EN 450-1:2012 Fly ash for concrete Definition, specifications and conformity criteria
BS EN 196-1:2016 Methods of testing cement Determination of strength
BS EN 450-2:2005 Fly ash for concrete Conformity evaluation
BS EN 1744-6:2006 Tests for chemical properties of aggregates Determination of the influence of recycled aggregate extract on the initial setting time of cement
BS EN 480-14:2006 Admixtures for concrete, mortar and grout. Test methods Determination of the effect on corrosion susceptibility of reinforcing steel by potentiostatic electro-chemical test
BS EN 13877-1:2013 Concrete pavements Materials
EN 197-2:2014 Cement - Part 2: Conformity evaluation
UNE-EN 413-1:2011 Masonry cement - Part 1: Composition, specifications and conformity criteria
UNE-EN 13877-2:2013 Concrete pavements - Part 2: Functional requirements for concrete pavements
BS EN 13364:2002 Natural stone test methods. Determination of the breaking load at dowel hole
BS EN 1992-1-1 : 2004 EUROCODE 2: DESIGN OF CONCRETE STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
UNE-EN 14227-5:2014 Hydraulically bound mixtures - Specifications - Part 5: Hydraulic road binder bound granular mixtures
BS EN 14227-4:2013 Hydraulically bound mixtures. Specifications Fly ash for hydraulically bound mixtures
DIN EN 1323:2007-11 ADHESIVES FOR TILES - CONCRETE SLABS FOR TESTS
I.S. EN 13914-1:2016 DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING
I.S. EN 14227-1:2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 1: CEMENT BOUND GRANULAR MIXTURES
DIN EN 14227-10:2006-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 10: SOIL TREATED BY CEMENT
EN 1323:2007 Adhesives for tiles - Concrete slabs for tests
DIN EN 14227-14:2006-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 14: SOIL TREATED BY FLY ASH
CEN/TR 196-4:2007 Methods of testing cement - Part 4: Quantitative determination of constituents
EN 12390-3:2009/AC:2011 TESTING HARDENED CONCRETE - PART 3: COMPRESSIVE STRENGTH OF TEST SPECIMENS
CEN/TR 16443:2013 Backgrounds to the revision of EN 450-1:2005+A1:2007 - Fly ash for concrete
DIN EN 14891:2017-05 LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, ASSESSMENT AND VERIFICATION OF CONSTANCY OF PERFORMANCE, CLASSIFICATION AND MARKING
DIN EN 1766:2017-05 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - REFERENCE CONCRETES FOR TESTING
DIN EN 14580:2005-07 Natural stone test methods - Determination of static elastic modulus; German version EN 14580:2005
DIN EN 14649:2005-07 PRECAST CONCRETE PRODUCTS - TEST METHOD FOR STRENGTH RETENTION OF GLASS FIBRES IN CEMENT AND CONCRETE (SIC TEST)
EN 12848:2009 Bitumen and bituminous binders - Determination of mixing stability with cement of bituminous emulsions
EN 13263-1:2005+A1:2009 Silica fume for concrete - Part 1: Definitions, requirements and conformity criteria
CR 13902:2000 Test methods for determining the water/cement ratio of fresh concrete
EN 1051-1:2003 Glass in building - Glass blocks and glass pavers - Part 1: Definitions and description
DIN EN 14617-15:2005-06 AGGLOMERATED STONE - TEST METHODS - PART 15: DETERMINATION OF COMPRESSIVE STRENGTH
CEN/TS 14754-1:2007 Curing compounds - Test methods - Part 1: Determination of water retention efficiency of common curing compounds
CEN/TR 16563:2013 Principles of the equivalent durability procedure
EN 13084-5:2005/AC:2006 FREE-STANDING CHIMNEYS - PART 5: MATERIAL FOR BRICK LINERS - PRODUCT SPECIFICATIONS
EN 13139:2002/AC:2004 AGGREGATES FOR MORTAR
ONORM EN 14487-1 : 2006 SPRAYED CONCRETE - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY
UNI EN 480-15 : 2013 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 15: REFERENCE CONCRETE AND METHOD FOR TESTING VISCOSITY MODIFYING ADMIXTURES
10/30200034 DC : 0 BS EN 13282-1 - HYDRAULIC ROAD BINDERS - PART 1: RAPID HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
DIN EN 15191:2010-04 Precast concrete products - Classification of glassfibre reinforced concrete performance
S.R. CEN/TR 15678:2008 CONCRETE - RELEASE OF REGULATED DANGEROUS SUBSTANCES INTO SOIL, GROUNDWATER AND SURFACE WATER - TEST METHOD FOR NEW OR UNAPPROVED CONSTITUENTS OF CONCRETE AND FOR PRODUCTION CONCRETES
17/30348207 DC : DRAFT MAY 2017 BS ISO 19426-2 - STRUCTURES FOR MINE SHAFTS - PART 2: HEADFRAME STRUCTURES
PD CEN/TR 16349:2012 Framework for a specification on the avoidance of a damaging Alkali-Silica Reaction (ASR) in concrete
I.S. EN 14227-12:2006 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 12: SOIL TREATED BY SLAG
11/30203534 DC : DRAFT AUG 2011 BS ISO 13270 - STEEL FIBRES FOR CONCRETE - DEFINITIONS AND SPECIFICATIONS
BS EN 16572:2015 Conservation of cultural heritage. Glossary of technical terms concerning mortars for masonry, renders and plasters used in cultural heritage
08/30192723 DC : 0 BS EN 1536 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - BORED PILES
03/303958 DC : DRAFT APR 2003 EN 14679 - EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DEEP MIXING
BS EN 15743 : 2010 SUPERSULFATED CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
NF EN 15368 : 2009 + A1 2010 HYDRAULIC BINDER FOR NON-STRUCTURAL APPLICATIONS - DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
BS EN 480-15:2013 Admixtures for concrete, mortar and grout. Test methods Reference concrete and method for testing viscosity modifying admixtures
S.R. CEN/TR 16349:2012 FRAMEWORK FOR A SPECIFICATION ON THE AVOIDANCE OF A DAMAGING ALKALI-SILICA REACTION (ASR) IN CONCRETE
BS EN 15191:2009 Precast concrete products. Classification of glassfibre reinforced concrete performance
BS EN 14227-15:2015 Hydraulically bound mixtures. Specifications Hydraulically stabilized soils
13/30265753 DC : 0 BS EN 13914-2 - DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: DESIGN CONSIDERATIONS AND ESSENTIAL PRINCIPLES FOR INTERNAL PLASTERING
04/30088151 DC : DRAFT FEB 2004 EN 1744-6 - TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 6: DETERMINATION OF THE INFLUENCE OF AGGREGATE EXTRACT ON THE INITIAL SETTING TIME OF CEMENT
DIN EN 15368 E : 2010 HYDRAULIC BINDER FOR NON-STRUCTURAL APPLICATIONS - DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
11/30240495 DC : 0 BS EN 14227-5 - HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 5: HYDRAULIC ROAD BINDER BOUND MIXTURES
11/30240501 DC : 0 BS EN 14227-3 - HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 3: FLY ASH BOUND MIXTURES
15/30328074 DC : 2015-12 BS EN 16907-4 - EARTHWORKS - PART 4: SOIL TREATMENT WITH LIME AND/OR HYDRAULIC BINDERS
11/30240492 DC : 0 BS EN 14227-4 - SPECIFICATIONS - PART 4: FLY ASH FOR HYDRAULICALLY BOUND MIXTURES
12/30254896 DC : 0 BS EN 197-2 - CEMENT - PART 2: CONFORMITY EVALUATION
UNI EN 15542 : 2008 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
BS EN ISO 21809-5:2017 Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems External concrete coatings
11/30248435 DC : 0 BS EN 14891 - LIQUID-APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION
DIN EN 15542 E : 2008 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
02/104236 DC : DRAFT JUNE 2002 EN 14487-1 - SPRAYED CONCRETE - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY
07/30164079 DC : 0 BS ISO 679 - METHODS OF TESTING CEMENTS - DETERMINATION OF STRENGTH
14/30314741 DC : 0 BS EN 14891 - LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION
UNE-EN 15368:2010 Hydraulic binder for non-structural applications: definition, specifications and conformity criteria
13/30282202 DC : 0 BS EN 16622 - HYDRAULIC SILICA-CALCIUM FUME FOR CONCRETE - DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
DIN EN 13282-1:2013-06 Hydraulic road binders - Part 1: Rapid hardening hydraulic road binders - Composition, specifications and conformity criteria
PREN 492 : DRAFT 2010 FIBRE-CEMENT SLATES AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS
DIN EN 16622:2016-02 SILICA-CALCIUM FUME FOR CONCRETE - DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
I.S. EN 492:2012 Fibre-cement slates and fittings - Product specification and test methods
I.S. EN 19694-3:2016 STATIONARY SOURCE EMISSIONS - DETERMINATION OF GREENHOUSE GAS (GHG) EMISSIONS IN ENERGY-INTENSIVE INDUSTRIES - PART 3: CEMENT INDUSTRY
I.S. EN 10298:2005 STEEL TUBES AND FITTINGS FOR ON SHORE AND OFFSHORE PIPELINES - INTERNAL LINING WITH CEMENT MORTAR
UNE-EN 14891:2017 Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives - Requirements, test methods, assessment and verification of constancy of performance, classification and marking
ISO 21809-5:2017 Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 5: External concrete coatings
S.R. CEN/TS 14754-1:2007 CURING COMPOUNDS - TEST METHODS - PART 1: DETERMINATION OF WATER RETENTION EFFICIENCY OF COMMON CURING COMPOUNDS
I.S. EN 14227-15:2015 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 15: HYDRAULICALLY STABILIZED SOILS
S.R. CR 13933:2000 MASONRY CEMENT - TESTING FOR WORKABILITY (COHESIVITY)
DIN EN 196-6:2010-05 METHODS OF TESTING CEMENT - PART 6: DETERMINATION OF FINENESS
BS EN 196-6:2010 Methods of testing cement Determination of fineness
EN 12467:2012+A2:2018 Fibre-cement flat sheets - Product specification and test methods
DIN EN 197-2:2014-05 CEMENT - PART 2: CONFORMITY EVALUATION
I.S. EN 15422:2008 PRECAST CONCRETE PRODUCTS - SPECIFICATION OF GLASSFIBRES FOR REINFORCEMENT OF MORTARS AND CONCRETES
DIN EN 196-5:2011-06 Methods of testing cement - Part 5: Pozzolanicity test for pozzolanic cement
DIN EN 12848:2009-07 BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF MIXING STABILITY WITH CEMENT OF BITUMINOUS EMULSIONS
DIN EN 14487-1:2006-03 Sprayed concrete - Part 1: Definitions, specifications and conformity
DIN EN 480-13:2015-08 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 13: REFERENCE MASONRY MORTAR FOR TESTING MORTAR ADMIXTURES
DIN EN 1367-4:2008-06 TESTS FOR THERMAL AND WEATHERING PROPERTIES OF AGGREGATES - PART 4: DETERMINATION OF DRYING SHRINKAGE
DIN EN 14227-4:2013-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 4: FLY ASH FOR HYDRAULICALLY BOUND MIXTURES
DIN EN 14216:2015-09 CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR VERY LOW HEAT SPECIAL CEMENTS
DIN EN 14891 E : 2017 LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, ASSESSMENT AND VERIFICATION OF CONSTANCY OF PERFORMANCE, CLASSIFICATION AND MARKING
DIN EN 14679:2005-07 Execution of special geotechnical works - Deep mixing
DIN EN 14618:2009-10 AGGLOMERATED STONE - TERMINOLOGY AND CLASSIFICATION
BS EN 13914-2:2016 Design, preparation and application of external rendering and internal plastering Internal plastering
BS EN 13863-4:2012 Concrete pavements Test methods for the determination of wear resistance of concrete pavements to studded tyres
BS EN 12848:2009 Bitumen and bituminous binders. Determination of mixing stability with cement of bituminous emulsions
DIN EN 14891:2015-02 (Draft) LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, ASSESSMENT AND VERIFICATION OF CONSTANCY OF PERFORMANCE, CLASSIFICATION AND MARKING
UNE-EN 196-9:2011 Methods of testing cement - Part 9: Heat of hydration - Semi-adiabatic method
BS EN 447:2007 Grout for prestressing tendons. Basic requirements
UNE-EN 545:2011 Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
BS EN 13084-5:2005 Free-standing chimneys Material for brick liners. Product specifications
BS EN 1766:2017 Products and systems for the protection and repair of concrete structures. Test methods. Reference concretes for testing
BS EN 13748-1 : 2004 TERRAZZO TILES - PART 1: TERRAZZO TILES FOR INTERNAL US
BS EN 14617-8:2007 Agglomerated stone. Test methods Determination of resistance to fixing (dowel hole)
I.S. EN 1504-1:2005 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND EVALUATION OF CONFORMITY - PART 1: DEFINITIONS
I.S. EN 13877-1:2013 CONCRETE PAVEMENTS - PART 1: MATERIALS
I.S. EN 12848:2009 BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF MIXING STABILITY WITH CEMENT OF BITUMINOUS EMULSIONS
I.S. EN 1766:2017 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - REFERENCE CONCRETES FOR TESTING
I.S. EN 14618:2009 AGGLOMERATED STONE - TERMINOLOGY AND CLASSIFICATION
I.S. EN 14216:2015 CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR VERY LOW HEAT SPECIAL CEMENTS
I.S. EN 450-1:2012 FLY ASH FOR CONCRETE - PART 1: DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
DIN EN 12390-3:2009-07 TESTING HARDENED CONCRETE - PART 3: COMPRESSIVE STRENGTH OF TEST SPECIMENS
I.S. EN 13877-2:2013 CONCRETE PAVEMENTS - PART 2: FUNCTIONAL REQUIREMENTS FOR CONCRETE PAVEMENTS
I.S. EN 196-9:2010 METHODS OF TESTING CEMENT - PART 9: HEAT OF HYDRATION - SEMI-ADIABATIC METHOD
I.S. EN 480-13:2015 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 13: REFERENCE MASONRY MORTAR FOR TESTING MORTAR ADMIXTURES
I.S. EN 13863-4:2012 CONCRETE PAVEMENTS - PART 4: TEST METHODS FOR THE DETERMINATION OF WEAR RESISTANCE OF CONCRETE PAVEMENTS TO STUDDED TYRES
I.S. EN 459-1:2015 BUILDING LIME - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY CRITERIA
I.S. EN 14227-5:2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 5: HYDRAULIC ROAD BINDER BOUND GRANULAR MIXTURES
DIN EN 13286-49:2004-06 Unbound and hydraulically bound mixtures - Part 49: Accelerated swelling test for soil treated by lime and/or hydraulic binder
I.S. EN 480-1:2014 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 1: REFERENCE CONCRETE AND REFERENCE MORTAR FOR TESTING
DIN EN 12878:1999-09 PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
DIN EN 413-1:2011-07 Masonry cement - Part 1: Composition, specifications and conformity criteria
DIN EN 197-2:2000-11 CEMENT - PART 2: CONFORMITY EVALUATION
I.S. EN 14227-4:2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 4: FLY ASH FOR HYDRAULICALLY BOUND MIXTURES
I.S. EN 196-8:2010 METHODS OF TESTING CEMENT - PART 8: HEAT OF HYDRATION - SOLUTION METHOD
I.S. EN 934-4:2009 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - PART 4: ADMIXTURES FOR GROUT FOR PRESTRESSING TENDONS - DEFINITIONS, REQUIREMENTS, CONFORMITY, MARKING AND LABELLING
I.S. EN 13263-1:2005 SILICA FUME FOR CONCRETE - PART 1: DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
I.S. EN 447:2007 GROUT FOR PRESTRESSING TENDONS - BASIC REQUIREMENTS
I.S. EN 545:2010 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS
I.S. EN 13914-2:2016 DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: INTERNAL PLASTERING
I.S. EN 12878:2014 PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
DIN EN 1504-1:2005-10 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 1: Definitions
I.S. EN 196-5:2011 METHODS OF TESTING CEMENT - PART 5: POZZOLANICITY TEST FOR POZZOLANIC CEMENT
I.S. EN 413-1:2011 MASONRY CEMENT - PART 1: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
I.S. EN 1367-4:2008 TESTS FOR THERMAL AND WEATHERING PROPERTIES OF AGGREGATES - PART 4: DETERMINATION OF DRYING SHRINKAGE
I.S. EN 1926:2006 NATURAL STONE TEST METHODS - DETERMINATION OF UNIAXIAL COMPRESSIVE STRENGTH
DIN EN 197-4:2004-08 CEMENT - PART 4: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR LOW EARLY STRENGTH BLAST FURNACE CEMENTS
I.S. EN 14227-3:2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 3: FLY ASH BOUND GRANULAR MIXTURES
I.S. EN 14891:2017 LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, ASSESSMENT AND VERIFICATION OF CONSTANCY OF PERFORMANCE, CLASSIFICATION AND MARKING
DIN EN 206-1:2001-07 CONCRETE - PART 1: SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
I.S. EN 1744-1:2009 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 1: CHEMICAL ANALYSIS
I.S. EN 494:2012 FIBRE-CEMENT PROFILED SHEETS AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS
I.S. EN 196-1:2016 METHODS OF TESTING CEMENT - PART 1: DETERMINATION OF STRENGTH
UNI EN 12878 : 2014 PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
I.S. EN 14487-1:2005 SPRAYED CONCRETE - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY
BS 6699:1992 Specification for ground granulated blastfurnace slag for use with Portland cement
ISO 19426-5:2018 Structures for mine shafts — Part 5: Shaft system structures
02/107035 DC : DRAFT NOV 2002 BS EN 14580 - NATURAL STONE TEST METHODS - DETERMINATION OF STATIC ELASTIC MODULUS
UNE-EN 1992-1-1:2013 Eurocode 2: Design of concrete structures - Part 1-1: General rules and rules for buildings
I.S. EN 450-2:2005 FLY ASH FOR CONCRETE - PART 2: CONFORMITY EVALUATION
BS EN 12467 : 2012 FIBRE-CEMENT FLAT SHEETS - PRODUCT SPECIFICATION AND TEST METHODS
BS ISO 29581-2:2010 Cement. Test methods Chemical analysis by X-ray fluorescence
I.S. EN 1323:2007 ADHESIVES FOR TILES - CONCRETE SLABS FOR TESTS
08/30180275 DC : 0 BS EN 934-4 - ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - PART 4: ADMIXTURES FOR GROUT FOR PRESTRESSING TENDONS - DEFINITIONS, REQUIREMENTS, CONFORMITY, MARKING AND LABELLING
I.S. EN 15368:2008 HYDRAULIC BINDER FOR NON-STRUCTURAL APPLICATIONS - DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
PREN 934-4 : DRAFT 2008 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - PART 4: ADMIXTURES FOR GROUT FOR PRESTRESSING TENDONS - DEFINITIONS, REQUIREMENTS, CONFORMITY, MARKING AND LABELLING
PD CEN/TR 14245:2014 Cement. Guidelines for the application of EN 197-2 Conformity Evaluation
DIN EN 13282-2 E : 2015 HYDRAULIC ROAD BINDERS - PART 2: NORMAL HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
I.S. EN 206-1:2002 CONCRETE - PART 1: SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY (INCLUDING IRISH NATIONAL ANNEX)
DD CEN/TS 14754-1:2007 Curing compounds. Test methods Determination of water retention efficiency of common curing compounds
UNE-EN 15743:2010 Supersulfated cement - Composition, specifications and conformity criteria
06/30153627 DC : 0 EN 1323 - ADHESIVES FOR TILES - CONCRETE SLABS FOR TESTS
PD CEN/TR 16443:2013 Backgrounds to the revision of EN 450-1:2005+A1:2007. Fly ash for concrete
DIN EN 480-15:2013-06 Admixtures for concrete, mortar and grout - Test methods - Part 15: Reference concrete and method for testing viscosity modifying admixtures
DIN EN 15743:2015-06 SUPERSULFATED CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
14/30278089 DC : 0 BS ISO 13007-5 - CERAMIC TILES - GROUTS AND ADHESIVES - PART 5: LIQUID APPLIED WATERPROOFING MEMBRANES FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION
PREN 12467 : DRAFT 2010 FIBRE-CEMENT FLAT SHEETS - PRODUCT SPECIFICATION AND TEST METHODS
02/104525 DC : DRAFT JULY 2002 EN 13263-1 - SILICA FUME FOR CONCRETE - PART 1: DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
BS ISO 13270:2013 Steel fibres for concrete. Definitions and specifications
I.S. EN 14617-8:2007 AGGLOMERATED STONE - TEST METHODS - PART 8: DETERMINATION OF RESISTANCE TO FIXING (DOWEL HOLE)
PD CEN/TR 196-4:2007 Methods of testing cement Quantitative determination of constituents
14/30310833 DC : 0 BS EN 1538:2010/A1 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - DIAPHRAGM WALLS
S.R. CEN/TR 14245:2014 CEMENT - GUIDELINES FOR THE APPLICATION OF EN 197-2 CONFORMITY EVALUATION
PREN 14891 : DRAFT 2014 LIQUID APPLIED WATER IMPERMEABLE PRODUCTS FOR USE BENEATH CERAMIC TILING BONDED WITH ADHESIVES - REQUIREMENTS, TEST METHODS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION
07/30172380 DC : 0 BS EN 14490 - EXECUTION OF SPECIAL GEOTECHNICAL WORKS - SOIL NAILING
02/103010 DC : DRAFT APR 2002 PREN 13914-2 - DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: INTERNAL PLASTERING
DIN EN 16908 E : 2017 CEMENT AND BUILDING LIME - ENVIRONMENTAL PRODUCT DECLARATIONS - PRODUCT CATEGORY RULES COMPLEMENTARY TO EN 15804
17/30348216 DC : 0 BS ISO 19426-5 - STRUCTURES FOR MINE SHAFTS - PART 5: SHAFT SYSTEM STRUCTURES
ISO 19426-2:2018 Structures for mine shafts — Part 2: Headframe structures
PREN 13375 : DRAFT 2017 FLEXIBLE SHEETS FOR WATERPROOFING - WATERPROOFING OF CONCRETE BRIDGE DECKS AND OTHER CONCRETE SURFACES TRAFFICABLE BY VEHICLES - SPECIMEN PREPARATION
BS EN 492 : 2012 FIBRE-CEMENT SLATES AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS
UNE-EN 14227-15:2017 Hydraulically bound mixtures - Specifications - Part 15: Hydraulically stabilized soils
CR 13933:2000 Masonry cement - Testing for workability (cohesivity)
PREN 197-2 : DRAFT 2012 CEMENT - PART 2: CONFORMITY EVALUATION
EN ISO 21809-5:2017 Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 5: External concrete coatings (ISO 21809-5:2017)
UNE-EN 480-15:2013 Admixtures for concrete, mortar and grout - Test methods - Part 15: Reference concrete and method for testing viscosity modifying admixtures
DIN EN 12004-2:2015-02 (Draft) ADHESIVES FOR CERAMIC TILES - PART 2: TEST METHODS
PREN 14227-3 : DRAFT 2011 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 3: FLY ASH BOUND MIXTURES
I.S. EN 12390-3:2009 TESTING HARDENED CONCRETE - PART 3: COMPRESSIVE STRENGTH OF TEST SPECIMENS
S.R. CR 14245:2001 GUIDELINES FOR THE APPLICATION OF EN 197-2 'CONFORMITY EVALUATION'
DIN EN 13263-1:2009-07 SILICA FUME FOR CONCRETE - PART 1: DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
DIN EN 12878:2014-07 PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
DIN EN 1744-1:2013-03 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 1: CHEMICAL ANALYSIS
DIN EN 934-5:2008-02 Admixtures for concrete, mortar and grout - Part 5: Admixtures for sprayed concrete - Definitions, requirements, conformity, marking and labelling
DIN EN 13084-5:2005-12 Free-standing chimneys - Part 5: Material for brick liners - Product specifications
DIN EN 196-9:2010-07 Methods of testing cement - Part 9: Heat of hydration - Semi-adiabatic method
DIN EN 934-4:2009-09 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - PART 4: ADMIXTURES FOR GROUT FOR PRESTRESSING TENDONS - DEFINITIONS, REQUIREMENTS, CONFORMITY, MARKING AND LABELLING
DIN EN 13748-1:2005-08 TERRAZZO TILES - PART 1: TERRAZZO TILES FOR INTERNAL USE
DIN EN 934-1:2008-04 Admixtures for concrete, mortar and grout - Part 1: Common requirements
DIN EN 480-14:2007-03 Admixtures for concrete, mortar and grout - Test methods - Part 14: Determination of the effect on corrosion susceptibility of reinforcing steel by potentiostatic electro-chemical test
DIN EN 1926:2007-03 Natural stone test methods - Determination of uniaxial compressive strength
DIN EN 1766:2015-07 (Draft) PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - REFERENCE CONCRETES FOR TESTING
DIN EN 1744-6:2006-12 Tests for chemical properties of aggregates - Part 6: Determination of the influence of recycled aggregate extract on the initial setting time of cement
DIN EN 480-1:2015-01 Admixtures for concrete, mortar and grout - Test methods - Part 1: Reference concrete and reference mortar for testing
DIN EN 14617-15 E : 2005 AGGLOMERATED STONE - TEST METHODS - PART 15: DETERMINATION OF COMPRESSIVE STRENGTH
DIN EN 494:2015-12 FIBRE-CEMENT PROFILED SHEETS AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS
DIN EN 14617-8:2008-01 AGGLOMERATED STONE - TEST METHODS - PART 8: DETERMINATION OF RESISTANCE TO FIXING (DOWEL HOLE)
DIN EN 13914-1:2016-09 DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING
DIN EN 459-1:2015-07 BUILDING LIME - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY CRITERIA
DIN EN 13914-2:2016-09 DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: INTERNAL PLASTERING
DIN EN 14618 E : 2009 AGGLOMERATED STONE - TERMINOLOGY AND CLASSIFICATION
DIN EN 14649 E : 2005 PRECAST CONCRETE PRODUCTS - TEST METHOD FOR STRENGTH RETENTION OF GLASS FIBRES IN CEMENT AND CONCRETE (SIC TEST)
DIN EN 14647:2006-01 Calcium aluminate cement - Composition, specifications and conformity criteria
BS EN 14227-14:2006 Hydraulically bound mixtures. Specifications Soil treated by fly ash
BS EN 545:2010 Ductile iron pipes, fittings, accessories and their joints for water pipelines. Requirements and test methods
BS EN 14227-5:2013 Hydraulically bound mixtures. Specifications Hydraulic road binder bound granular mixtures
BS EN 14647:2005 Calcium aluminate cement. Composition, specifications and conformity criteria
UNE-EN 480-13:2015 Admixtures for concrete, mortar and grout - Test methods - Part 13: Reference masonry mortar for testing mortar admixtures
UNE-EN 459-1:2016 Building lime - Part 1: Definitions, specifications and conformity criteria
BS EN 197-2:2014 Cement Conformity evaluation
BS EN 1051-1:2003 Glass in building. Glass blocks and glass pavers Definitions and description
BS EN 588-2:2001 Fibre-cement pipes for sewers and drains Manholes and inspection chambers
BS EN 494 : 2012 FIBRE-CEMENT PROFILED SHEETS AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS
BS EN 13880-12:2003 Hot applied joint sealants Test method for the manufacture of concrete test blocks for bond testing (recipe methods)
UNE-EN 480-1:2015 Admixtures for concrete, mortar and grout - Test methods - Part 1: Reference concrete and reference mortar for testing
EN 196-6:2010 Methods of testing cement - Part 6: Determination of fineness
I.S. EN 1992-1-1:2004 EUROCODE 2: DESIGN OF CONCRETE STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
EN 13914-1:2016 Design, preparation and application of external rendering and internal plastering - Part 1: External rendering
EN 196-5:2011 Methods of testing cement - Part 5: Pozzolanicity test for pozzolanic cement
EN 196-9:2010 Methods of testing cement - Part 9: Heat of hydration - Semi-adiabatic method
EN 13880-12:2003 Hot applied joint sealants - Part 12: Test method for the manufacture of concrete test blocks for bond testing (recipe methods)
UNI EN 14618 : 2009 AGGLOMERATED STONE - TERMINOLOGY AND CLASSIFICATION
UNI EN 13084-5 : 2005 FREE-STANDING CHIMNEYS - PART 5: MATERIAL FOR BRICK LINERS - PRODUCT SPECIFICATIONS
UNI EN 1744-1 : 2013 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 1: CHEMICAL ANALYSIS
UNI EN 12848 : 2009 BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF MIXING STABILITY WITH CEMENT OF BITUMINOUS EMULSIONS
UNI EN 413-1 : 2011 MASONRY CEMENT - PART 1: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
UNI EN 13139 : 2013 AGGREGATES FOR MORTAR
UNI EN 196-8 : 2010 METHODS OF TESTING CEMENT - PART 8: HEAT OF HYDRATION - SOLUTION METHOD
UNI EN 13263-1 : 2009 SILICA FUME FOR CONCRETE - PART 1: DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
UNI EN 1367-4 : 2008 TESTS FOR THERMAL AND WEATHERING PROPERTIES OF AGGREGATES - PART 4: DETERMINATION OF DRYING SHRINKAGE
UNI EN 14647 : 2006 CALCIUM ALUMINATE CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
UNI EN 480-1 : 2014 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 1: REFERENCE CONCRETE AND REFERENCE MORTAR FOR TESTING
UNI EN 934-5 : 2008 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - PART 5: ADMIXTURES FOR SPRAYED CONCRETE - DEFINITIONS, REQUIREMENTS, CONFORMITY, MARKING AND LABELLING
UNI EN 14227-4 : 2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 4: FLY ASH FOR HYDRAULICALLY BOUND MIXTUREE
DIN EN 16908:2017-05 Cement and building lime - Environmental product declarations - Product category rules complementary to EN 15804
UNI EN 14679 : 2005 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DEEP MIXING
UNI EN 934-4 : 2009 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - PART 4: ADMIXTURES FOR GROUT FOR PRESTRESSING TENDONS - DEFINITIONS, REQUIREMENTS, CONFORMITY, MARKING AND LABELLING
UNI EN 15167-1 : 2006 GROUND GRANULATED BLAST FURNACE SLAG FOR USE IN CONCRETE, MORTAR AND GROUT - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY CRITERIA
UNI EN 14227-3 : 2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 3: FLY ASH BOUND GRANULAR MIXTURES
UNI EN 13877-1 : 2013 CONCRETE PAVEMENTS - PART 1: MATERIALS
UNI EN 1744-6 : 2007 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 6: DETERMINATION OF THE INFLUENCE OF RECYCLED AGGREGATE EXTRACT ON THE INITIAL SETTING TIME OF CEMENT
UNI EN 13863-4 : 2012 CONCRETE PAVEMENTS - PART 4: TEST METHODS FOR THE DETERMINATION OF WEAR RESISTANCE OF CONCRETE PAVEMENTS TO STUDDED TYRES
IP 486 : 2009 BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF MIXING STABILITY WITH CEMENT OF BITUMINOUS EMULSIONS
EN 14487-1:2005 Sprayed concrete - Part 1: Definitions, specifications and conformity
UNI EN 545 : 2010 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS
UNI EN 450-1 : 2012 FLY ASH FOR CONCRETE - PART 1: DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
UNI EN 447 : 2007 GROUT FOR PRESTRESSING TENDONS - BASIC REQUIREMENTS
UNI EN 196-5 : 2011 METHODS OF TESTING CEMENT - PART 5: POZZOLANICITY TEST FOR POZZOLANIC CEMENT
UNI EN 14845-1 : 2007 TEST METHODS FOR FIBRES IN CONCRETE - PART 1: REFERENCE CONCRETES
UNI EN 12390-3 : 2009 TESTING HARDENED CONCRETE - PART 3: COMPRESSIVE STRENGTH OF TEST SPECIMENS
UNI EN 14227-1 : 2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 1: CEMENT BOUND GRANULAR MIXTURES
UNI CEN/TR 16563 : 2013 PRINCIPLES OF THE EQUIVALENT DURABILITY PROCEDURE
UNI EN 934-1 : 2008 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - PART 1: COMMON REQUIREMENTS
UNI EN 14227-5 : 2013 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 5: HYDRAULIC ROAD BINDER BOUND GRANULAR MIXTURES
UNI EN 13877-2 : 2013 CONCRETE PAVEMENTS - PART 2: FUNCTIONAL REQUIREMENTS FOR CONCRETE PAVEMENTS
UNI EN 196-9 : 2010 METHODS OF TESTING CEMENT - PART 9: HEAT OF HYDRATION - SEMI-ADIABATIC METHOD
UNI EN 480-14 : 2007 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 14: DETERMINATION OF THE EFFECT ON CORROSION SUSCEPTIBILITY OF REINFORCING STEEL BY POTENTIOSTATIC ELECTRO-CHEMICAL TEST
EN 206:2013+A1:2016 Concrete - Specification, performance, production and conformity
DIN V 4034-1:2004-08 PREFABRICATED CONCRETE MANHOLES, UNREINFORCED, STEEL FIBRE AND REINFORCED FOR DRAINS AND SEWERS - TYPE 1 AND TYPE 2 - PART 1: REQUIREMENTS, TEST METHODS AND EVALUATION OF CONFORMITY
16/30338749 DC : 0 BS EN ISO 21809-5 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 5: EXTERNAL CONCRETE COATINGS
15/30326191 DC : 0 BS EN 16908 - CEMENT AND BUILDING LIME - ENVIRONMENTAL PRODUCT DECLARATIONS - PRODUCT CATEGORY RULES COMPLEMENTARY TO EN 15804
DIN EN 14227-15 E : 2016 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 15: HYDRAULICALLY STABILIZED SOILS
PREN 13914-2 : DRAFT 2013 DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 2: DESIGN CONSIDERATIONS AND ESSENTIAL PRINCIPLES FOR INTERNAL PLASTERING
DIN EN 15542:2008-06 Ductile iron pipes, fittings and accessories - External cement mortar coating for pipes - Requirements and test methods
PREN 12878 : DRAFT 2012 PIGMENTS FOR THE COLOURING OF BUILDING MATERIALS BASED ON CEMENT AND/OR LIME - SPECIFICATIONS AND METHODS OF TEST
DIN V 18153:2003-10 CONCRETE MASONRY UNITS (NORMAL-WEIGHT CONCRETE)
01/104967 DC : DRAFT JUN 2001 PREN 197-3 - CEMENT - PART 3: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR LOW HEAT COMMON CEMENTS
03/310129 DC : DRAFT JULY 2003 EN 934-5 - ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - PART 5: ADMIXTURES FOR SPRAYED CONCRETE - DEFINITIONS, REQUIREMENTS AND CONFORMITY
UNI CEN/TR 14245 : 2015 CEMENT - GUIDELINES FOR THE APPLICATION OF EN 197-2 CONFORMITY EVALUATION
UNI EN ISO 21809-5 : 2010 PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 5: EXTERNAL CONCRETE COATINGS
10/30233185 DC : 0 BS EN 12467 - FIBRE-CEMENT FLAT SHEETS - PRODUCT SPECIFICATION AND TEST METHODS
UNE-EN 16622:2016 Silica-calcium fume for concrete - Definitions, requirements and conformity criteria
11/30251426 DC : DRAFT OCT 2011 BS EN 480-15 - ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 15: REFERENCE CONCRETE AND METHOD FOR TESTING VISCOSITY MODIFYING ADMIXTURES
BS ISO 13007-5:2015 Ceramic tiles. Grouts and adhesives Requirements, test methods, evaluation of conformity, classification and designation of liquid-applied waterproofing membranes for use beneath ceramic tiling bonded with adhesives
08/30164905 DC : DRAFT JUNE 2008 BS EN 12390-3 - TESTING HARDENED CONCRETE - PART 3: COMPRESSIVE STRENGTH OF TEST SPECIMENS
UNI EN 15422 : 2008 PRECAST CONCRETE PRODUCTS - SPECIFICATION OF GLASS-FIBRES FOR REINFORCEMENT OF MORTARS AND CONCRETES
I.S. EN 934-1:2008 ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - PART 1: COMMON REQUIREMENTS
DIN EN 15368:2010-11 Hydraulic binder for non-structural applications - Definition, specifications and conformity criteria (includes Amendment A1:2010)
14/30294810 DC : 0 BS EN 14227-15 - HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 15: HYDRAULICALLY STABILIZED SOILS
DIN EN 16572 E : 2015 CONSERVATION OF CULTURAL HERITAGE - GLOSSARY OF TECHNICAL TERMS CONCERNING MORTARS FOR MASONRY, RENDERS AND PLASTERS USED IN CULTURAL HERITAGE
I.S. EN 14227-14:2006 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 14: SOIL TREATED BY FLY ASH
14/30292279 DC : 0 BS EN 13230-1 - RAILWAY APPLICATIONS - TRACK - CONCRETE SLEEPERS AND BEARERS - PART 1: GENERAL REQUIREMENTS
PREN 14227-4 : DRAFT 2011 SPECIFICATIONS - PART 4: FLY ASH FOR HYDRAULICALLY BOUND MIXTURES
13/30265750 DC : 0 BS EN 13914-1 - DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING
07/30164098 DC : 0 BS ISO 29582-2 - METHODS OF TESTING CEMENT - DETERMINATION OF THE HEAT OF HYDRATION - PART 2: SEMI-ADIABATIC METHOD
08/30178800 DC : DRAFT MAY 2008 BS EN 196-6 - METHODS OF TESTING CEMENT - PART 6: DETERMINATION OF FINENESS
11/30240489 DC : 0 BS EN 14227-1 - HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 1: CEMENT BOUND GRANULAR MIXTURES
DIN EN 16908:2015-09 (Draft) CEMENT AND BUILDING LIME - ENVIRONMENTAL PRODUCT DECLARATIONS - PRODUCT CATEGORY RULES COMPLEMENTARY TO EN 15804
PD CEN/TR 15840:2009 Evaluation of conformity of fly ash for concrete. Guidelines for the application of EN 450-2
PREN 13230-1 : DRAFT 2014 RAILWAY APPLICATIONS - TRACK - CONCRETE SLEEPERS AND BEARERS - PART 1: GENERAL REQUIREMENTS
DIN EN 14227-15:2016-02 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 15: HYDRAULICALLY STABILIZED SOILS
PD CEN/TR 16563:2013 Principles of the equivalent durability procedure
DIN EN 15743 E : 2015 SUPERSULFATED CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
DIN EN 16622 E : 2016 SILICA-CALCIUM FUME FOR CONCRETE - DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
PREN 13139 : DRAFT 2015 AGGREGATES FOR MORTAR
BS EN 16622:2015 Silica-calcium fume for concrete. Definitions, requirements and conformity criteria
DIN EN 15422 E : 2008 PRECAST CONCRETE PRODUCTS - SPECIFICATION OF GLASSFIBRES FOR REINFORCEMENT OF MORTARS AND CONCRETES
DIN EN 206:2014-07 CONCRETE - SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
BS EN 15542:2008 Ductile iron pipes, fittings and accessories. External cement mortar coating for pipes. Requirements and test methods
DIN V 105-1:2002-06 CLAY MASONRY UNITS - PART 1: SOLID UNITS AND VERTICALLY PERFORATED UNITS OF BULK DENSITY CLASSES >= 1.2
UNI CEN/TR 15678 : 2008 CONCRETE - RELEASE OF REGULATED DANGEROUS SUBSTANCES INTO SOIL, GROUNDWATER AND SURFACE WATER - TEST METHOD FOR NEW OR UNAPPROVED CONSTITUENTS OF CONCRETE AND FOR PRODUCTION CONCRETES
02/103921 DC : DRAFT JUN 2002 ISO/DIS 863 - METHODS OF TESTING CEMENT - POZZOLANICITY TEST FOR POZZOLANIC CEMENT
UNI CEN/TR 16349 : 2013 FRAMEWORK FOR A SPECIFICATION ON THE AVOIDANCE OF A DAMAGING ALKALI-SILICA REACTION (ASR) IN CONCRETE
04/30083253 DC : DRAFT MAY 2004 EN 14944-1 - INFLUENCE OF CEMENTITIOUS PRODUCTS ON WATER INTENDED FOR HUMAN CONSUMPTION - TEST METHODS - PART 1: INFLUENCE OF FACTORY MADE CEMENTITIOUS PRODUCTS ON ORGANOLEPTIC PARAMETERS
I.S. CEN/TR 15125:2005 DESIGN, PREPARATION AND APPLICATION OF INTERNAL CEMENT AND/OR LIME PLASTERING SYSTEMS
08/30160023 DC : DRAFT AUG 2008 BS EN ISO 21809-5 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 5: EXTERNAL CONCRETE COATINGS
NF EN 14490 : 2010 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - SOIL NAILING
DIN EN 13282-1 E : 2013 HYDRAULIC ROAD BINDERS - PART 1: RAPID HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
DIN EN 14490 E : 2010 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - SOIL NAILING
I.S. EN 16572:2015 CONSERVATION OF CULTURAL HERITAGE - GLOSSARY OF TECHNICAL TERMS CONCERNING MORTARS FOR MASONRY, RENDERS AND PLASTERS USED IN CULTURAL HERITAGE
UNE-EN 492:2013 Fibre-cement slates and fittings - Product specification and test methods
I.S. EN 12004-2:2017 ADHESIVES FOR CERAMIC TILES - PART 2: TEST METHODS
UNI EN 14490 : 2010 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - SOIL NAILING
PREN 12390-3 : DRAFT 2017 TESTING HARDENED CONCRETE - PART 3: COMPRESSIVE STRENGTH OF TEST SPECIMENS
DD ENV 206:1992 Concrete. Performance, production, placing and compliance criteria
I.S. EN 16622:2015 SILICA-CALCIUM FUME FOR CONCRETE - DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
UNE-EN 12467:2013 Fibre-cement flat sheets - Product specification and test methods
I.S. EN 13282-2:2015 HYDRAULIC ROAD BINDERS - PART 2: NORMAL HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
ISO 13007-5:2015 Ceramic tiles Grouts and adhesives Part 5: Requirements, test methods, evaluation of conformity, classification and designation of liquid-applied waterproofing membranes for use beneath ceramic tiling bonded with adhesives
17/30360281 DC : 0 BS EN 13375 - FLEXIBLE SHEETS FOR WATERPROOFING - WATERPROOFING OF CONCRETE BRIDGE DECKS AND OTHER CONCRETE SURFACES TRAFFICABLE BY VEHICLES - SPECIMEN PREPARATION
17/30360096 DC : 0 BS EN 12390-3 - TESTING HARDENED CONCRETE - PART 3: COMPRESSIVE STRENGTH OF TEST SPECIMENS
CEN/TR 15840:2009 Evaluation of conformity of fly ash for concrete - Guidelines for the application of EN 450-2
UNE-EN 13282-1:2013 Hydraulic road binders - Part 1: Rapid hardening hydraulic road binders - Composition, specifications and conformity criteria
PREN 14227-1 : DRAFT 2011 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 1: CEMENT BOUND GRANULAR MIXTURES
EN 492:2012+A2:2018 Fibre-cement slates and fittings - Product specification and test methods
ISO/TR 12389:2009 Methods of testing cement Report of a test programme Chemical analysis by x-ray fluorescence
ISO 29582-1:2009 Methods of testing cement Determination of the heat of hydration Part 1: Solution method
I.S. EN 15191:2009 PRECAST CONCRETE PRODUCTS - CLASSIFICATION OF GLASSFIBRE REINFORCED CONCRETE PERFORMANCE
S.R. CR 13902:2000 TEST METHODS FOR DETERMINING THE WATER/CEMENT RATIO OF FRESH CONCRETE
S.R. CEN TR 196-4:2007 METHODS OF TESTING CEMENT - PART 4: QUANTITATIVE DETERMINATION OF CONSTITUENTS
I.S. EN 14490:2010 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - SOIL NAILING
I.S. EN 15542:2008 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
DIN EN 14580 E : 2005 NATURAL STONE TEST METHODS - DETERMINATION OF STATIC ELASTIC MODULUS
DIN EN 14679 E : 2005 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DEEP MIXING
DIN EN 14647 E : 2006 CALCIUM ALUMINATE CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
UNE-EN 13230-1:2016 Railway applications - Track - Concrete sleepers and bearers - Part 1: General requirements
BS EN 934-5:2007 Admixtures for concrete, mortar and grout Admixtures for sprayed concrete. Definitions, requirements, conformity, marking and labelling
BS EN 13263-1 : 2005 SILICA FUME FOR CONCRETE - PART 1: DEFINITIONS, REQUIREMENTS AND CONFORMITY CRITERIA
BS EN 14580:2005 Natural stone test methods. Determination of static elastic modulus
BS EN 14487-1:2005 Sprayed concrete Definitions, specifications and conformity
BS EN 196-9:2010 Methods of testing cement Heat of hydration. Semi-adiabatic method
BS EN 1744-1 : 2009 TESTS FOR CHEMICAL PROPERTIES OF AGGREGATES - PART 1: CHEMICAL ANALYSIS
UNE-EN 494:2013 Fibre-cement profiled sheets and fittings - Product specification and test methods
BS EN 14649:2005 Precast concrete products. Test method for strength retention of glass fibres in cement and concrete (SIC test)
BS EN 14845-1:2007 Test methods for fibres in concrete Reference concretes
BS EN 14227-12:2006 Hydraulically bound mixtures. Specifications. Soil treated by slag
UNI EN 197-2 : 2014 CEMENT - PART 2: CONFORMITY EVALUATION
UNE-EN 13877-1:2013 Concrete pavements - Part 1: Materials
BS EN 206-1:2000 Concrete Specification, performance, production and conformity
BS EN 12878:2014 Pigments for the colouring of building materials based on cement and/or lime. Specifications and methods of test
UNE-EN 13863-4:2012 Concrete pavements - Part 4: Test methods for the determination of wear resistance of concrete pavements to studded tyres
BS EN 1926:2006 Natural stone test methods. Determination of uniaxial compressive strength
BS EN 480-1:2014 Admixtures for concrete, mortar and grout. Test methods Reference concrete and reference mortar for testing
BS EN 846-13:2001 Methods of test for ancillary components for masonry Determination of resistance to impact, abrasion and corrosion of organic coatings
UNE-EN 14216:2015 Cement - Composition, specifications and conformity criteria for very low heat special cements
BS EN 459-1:2015 Building lime Definitions, specifications and conformity criteria
BS EN 13914-1:2016 Design, preparation and application of external rendering and internal plastering External rendering
BS EN 196-5:2011 Methods of testing cement Pozzolanicity test for pozzolanic cement
BS EN 14227-3:2013 Hydraulically bound mixtures. Specifications Fly ash bound granular mixtures
UNE-EN 934-4:2010 Admixtures for concrete, mortar and grout - Part 4: Admixtures for grout for prestressing tendons - Definitions, requirements, conformity, marking and labelling
BS EN 934-1:2008 Admixtures for concrete, mortar and grout Common requirements
BS EN 13139:2013 Aggregates for mortar
BS EN 13748-2:2004 Terrazzo tiles Terrazzo tiles for external use
I.S. EN 197-2:2014 CEMENT - PART 2: CONFORMITY EVALUATION
UNE-EN 1744-1:2010 Tests for chemical properties of aggregates - Part 1: Chemical analysis
CEN/TR 14245:2014 Cement - Guidelines for the application of EN 197-2 Conformity Evaluation
UNE-EN 14227-1:2014 Hydraulically bound mixtures - Specifications - Part 1: Cement bound granular mixtures
BS EN 14679:2005 Execution of special geotechnical works. Deep mixing
BS EN 1008:2002 Mixing water for concrete. Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete
BS EN 934-4:2009 Admixtures for concrete, mortar and grout Admixtures for grout for prestressing tendons. Definitions, requirements, conformity, marking and labelling
UNE-EN 14227-3:2014 Hydraulically bound mixtures - Specifications - Part 3: Fly ash bound granular mixtures
UNE-EN 196-8:2010 Methods of testing cement - Part 8: Heat of hydration - Solution method
BS EN 14227-10:2006 Hydraulically bound mixtures. Specifications Soil treated by cement
BS EN 196-8:2010 Methods of testing cement Heat of hydration. Solution method
BS EN 12390-3:2009 Testing hardened concrete Compressive strength of test specimens
UNE-EN 14227-4:2014 Hydraulically bound mixtures - Specifications - Part 4: Fly ash for hydraulically bound mixtures
BS EN 1504-1:2005 Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity Definitions
BS EN 14227-1:2013 Hydraulically bound mixtures. Specifications Cement bound granular mixtures
BS EN 13877-2:2013 Concrete pavements Functional requirements for concrete pavements
UNE-EN 14618:2011 Agglomerated stone - Terminology and classification
BS EN 14216:2015 Cement. Composition, specifications and conformity criteria for very low heat special cements
UNE-EN 450-1:2013 Fly ash for concrete - Part 1: Definition, specifications and conformity criteria
BS EN 1367-4:2008 Tests for thermal and weathering properties of aggregates Determination of drying shrinkage
CEN/TR 15678:2008 Concrete - Release of regulated dangerous substances into soil, groundwater and surface water - Test method for new or unapproved constituents of concrete and for production concretes
DIN EN 447:2017-09 Grout for prestressing tendons - Basic requirements
EN 14679:2005/AC:2006 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DEEP MIXING
EN 450-1:2012 Fly ash for concrete - Part 1: Definition, specifications and conformity criteria
EN 15422:2008 Precast concrete products - Specification of glassfibres for reinforcement of mortars and concretes
EN 15368:2008+A1:2010 Hydraulic binder for non-structural applications - Definition, specifications and conformity criteria
EN 16908:2017 Cement and building lime - Environmental product declarations - Product category rules complementary to EN 15804
EN 14617-8:2007 Agglomerated stone - Test methods - Part 8: Determination of resistance to fixing (dowel hole)
EN 14649 : 2005 PRECAST CONCRETE PRODUCTS - TEST METHOD FOR STRENGTH RETENTION OF GLASS FIBRES IN CEMENT AND CONCRETE (SIC TEST)
EN 14227-10:2006 Hydraulically bound mixtures - Specifications - Part 10: Soil treated by cement
EN 450-2:2005 Fly ash for concrete - Part 2: Conformity evaluation
EN 196-1:2016 Methods of testing cement - Part 1: Determination of strength
EN 588-2:2001 Fibre cement pipes for drains and sewers - Part 2: Manholes and inspection chambers
EN 413-1:2011 Masonry cement - Part 1: Composition, specifications and conformity criteria
EN 1744-1:2009+A1:2012 Tests for chemical properties of aggregates - Part 1: Chemical analysis
ENV 206 : 1990 CONCRETE - PERFORMANCE, PRODUCTION, PLACING AND COMPLIANCE CRITERIA
EN 14227-3:2013 Hydraulically bound mixtures - Specifications - Part 3: Fly ash bound granular mixtures
EN 1926:2006 Natural stone test methods - Determination of uniaxial compressive strength
EN 19694-3 : 2016 STATIONARY SOURCE EMISSIONS - DETERMINATION OF GREENHOUSE GAS (GHG) EMISSIONS IN ENERGY-INTENSIVE INDUSTRIES - PART 3: CEMENT INDUSTRY
EN 16622:2015 Silica-calcium fume for concrete - Definitions, requirements and conformity criteria
EN 14227-14:2006 Hydraulically bound mixtures - Specifications - Part 14: Soil treated by fly ash
EN 480-14:2006 Admixtures for concrete, mortar and grout - Test methods - Part 14: Determination of the effect on corrosion susceptibility of reinforcing steel by potentiostatic electro-chemical test
EN 14227-12:2006 Hydraulically bound mixtures - Specifications - Part 12: Soil treated by slag
EN 14891:2017 Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives - Requirements, test methods, assessment and verification of constancy of performance, classification and marking
EN 14490:2010 Execution of special geotechnical works - Soil nailing
EN 14227-15 : 2015 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 15: HYDRAULICALLY STABILIZED SOILS
EN 13748-2:2004 Terrazzo tiles - Part 2: Terrazzo tiles for external use
EN 16572:2015 Conservation of cultural heritage - Glossary of technical terms concerning mortars for masonry, renders and plasters used in cultural heritage
EN 14617-15:2005 Agglomerated stone - Test methods - Part 15: Determination of compressive strength
EN 14845-1:2007 Test methods for fibres in concrete - Part 1: Reference concretes
EN 13748-1:2004/A1:2005 TERRAZZO TILES - PART 1: TERRAZZO TILES FOR INTERNAL USE
EN 14580:2005 Natural stone test methods - Determination of static elastic modulus
EN 13877-1:2013 Concrete pavements - Part 1: Materials
EN 14216:2015 Cement - Composition, specifications and conformity criteria for very low heat special cements
EN 15743:2010+A1:2015 Supersulfated cement - Composition, specifications and conformity criteria
EN 12878:2014 Pigments for the colouring of building materials based on cement and/or lime - Specifications and methods of test
EN 13863-4:2012 Concrete pavements - Part 4: Test methods for the determination of wear resistance of concrete pavements to studded tyres
EN 14647:2005/AC:2006 CALCIUM ALUMINATE CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
EN 1744-6:2006 Tests for chemical properties of aggregates - Part 6: Determination of the influence of recycled aggregate extract on the initial setting time of cement
EN 447:2007 Grout for prestressing tendons - Basic requirements
EN 1367-4:2008 Tests for thermal and weathering properties of aggregates - Part 4: Determination of drying shrinkage
EN 480-15:2013 Admixtures for concrete, mortar and grout - Test methods - Part 15: Reference concrete and method for testing viscosity modifying admixtures
EN 934-4:2009 Admixtures for concrete, mortar and grout - Part 4: Admixtures for grout for prestressing tendons - Definitions, requirements, conformity, marking and labelling
EN 196-8:2010 Methods of testing cement - Part 8: Heat of hydration - Solution method
EN 1766:2017 Products and systems for the protection and repair of concrete structures - Test methods - Reference concretes for testing
EN 14227-4:2013 Hydraulically bound mixtures - Specifications - Part 4: Fly ash for hydraulically bound mixtures
EN 197-4:2004 Cement - Part 4: Composition, specifications and conformity criteria for low early strength blastfurnace cements
EN 13877-2:2013 Concrete pavements - Part 2: Functional requirements for concrete pavements
EN 1992-1-1:2004/A1:2014 EUROCODE 2: DESIGN OF CONCRETE STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
EN 14227-5:2013 Hydraulically bound mixtures - Specifications - Part 5: Hydraulic road binder bound granular mixtures
EN 1504-1:2005 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 1: Definitions
EN 15542:2008 Ductile iron pipes, fittings and accessories - External cement mortar coating for pipes - Requirements and test methods
EN 494:2012+A1:2015 Fibre-cement profiled sheets and fittings - Product specification and test methods
EN 15167-1:2006 Ground granulated blast furnace slag for use in concrete, mortar and grout - Part 1: Definitions, specifications and conformity criteria
EN 14618:2009 Agglomerated stone - Terminology and classification
EN 480-13:2015 Admixtures for concrete, mortar and grout - Test methods - Part 13: Reference masonry mortar for testing mortar admixtures
EN 846-13:2001 Methods of test for ancillary components for masonry - Part 13: Determination of resistance to impact, abrasion and corrosion of organic coatings
EN 934-5:2007 Admixtures for concrete, mortar and grout - Part 5: Admixtures for sprayed concrete - Definitions, requirements, conformity, marking and labelling
EN 206-1:2000/A2:2005 CONCRETE - PART 1: SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
EN 15191:2009 Precast concrete products - Classification of glassfibre reinforced concrete performance
EN 459-1:2015 BUILDING LIME - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY CRITERIA
EN 934-1:2008 Admixtures for concrete, mortar and grout - Part 1: Common requirements
EN 14227-1:2013 Hydraulically bound mixtures - Specifications - Part 1: Cement bound granular mixtures
EN 480-1:2014 Admixtures for concrete, mortar and grout - Test methods - Part 1: Reference concrete and reference mortar for testing
EN 13914-2:2016 Design, preparation and application of external rendering and internal plastering - Part 2: Internal plastering
ISO 29582-2:2009 Methods of testing cement Determination of the heat of hydration Part 2: Semi-adiabatic method
DIN V 18151:2003-10 LIGHTWEIGHT HOLLOW BLOCKS
DIN EN 14490:2010-11 Execution of special geotechnical works - Soil nailing
05/30139297 DC : DRAFT SEP 2005 EN 447 - GROUT FOR PRESTRESSING TENDONS - BASIC REQUIREMENTS
10/30200038 DC : 0 BS EN 13282-2 - HYDRAULIC ROAD BINDERS - PART 2: NORMAL HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
PD ISO/TR 12389:2009 Methods of testing cement. Report of a test programme. Chemical analysis by x-ray fluorescence
PD CEN/TR 16912:2016 Guidelines for a procedure to support the European standardization of cements
I.S. EN 14227-10:2006 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 10: SOIL TREATED BY CEMENT
I.S. EN 197-4:2004 CEMENT - PART 4: COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA FOR LOW EARLY STRENGTH BLASTFURNACE CEMENTS
PREN 12716 : DRAFT 2017 EXECUTION OF SPECIAL GEOTECHNICAL WORKS - JET GROUTING
DIN EN 12004-2 E : 2017 ADHESIVES FOR CERAMIC TILES - PART 2: TEST METHODS
I.S. EN 16908:2017 CEMENT AND BUILDING LIME - ENVIRONMENTAL PRODUCT DECLARATIONS - PRODUCT CATEGORY RULES COMPLEMENTARY TO EN 15804
08/30181473 DC : DRAFT JULY 2008 BS EN 545 - DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS
BS EN 10298:2005 Steel tubes and fittings for onshore and offshore pipelines. Internal lining with cement mortar
PREN 1538 : DRAFT 2008 EXECUTION OF SPECIAL GEOTECHNICAL WORK - DIAPHRAGM WALLS
BS EN 16908:2017 Cement and building lime. Environmental product declarations. Product category rules complementary to EN 15804
PREN 14227-5 : DRAFT 2011 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 5: HYDRAULIC ROAD BINDER BOUND MIXTURES
I.S. EN 14617-15:2005 AGGLOMERATED STONE - TEST METHODS - PART 15: DETERMINATION OF COMPRESSIVE STRENGTH
12/30257889 DC : 0 BS EN 206 - CONCRETE - SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
05/30129415 DC : DRAFT FEB 2005 BS EN 480-1 - ADMIXTURES FOR CONCRETE, MORTAR AND GROUT - TEST METHODS - PART 1: REFERENCE CONCRETE AND REFERENCE MORTAR FOR TESTING
BS EN 13282-1:2013 Hydraulic road binders Rapid hardening hydraulic road binders. Composition, specifications and conformity criteria
DIN EN 16572:2015-10 CONSERVATION OF CULTURAL HERITAGE - GLOSSARY OF TECHNICAL TERMS CONCERNING MORTARS FOR MASONRY, RENDERS AND PLASTERS USED IN CULTURAL HERITAGE
15/30324098 DC : 0 BS EN 1766 - PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - TEST METHODS - REFERENCE CONCRETES FOR TESTING
07/30164088 DC : 0 BS ISO 29582-1 - METHODS OF TESTING CEMENT - DETERMINATION OF THE HEAT OF HYDRATION - PART 1: SOLUTION METHOD
BS EN 13282-2:2015 Hydraulic road binders Normal hardening hydraulic road binders. Composition, specifications and conformity criteria
03/303925 DC : DRAFT MAR 2003 BS EN 14647 - CALCIUM ALUMINATE CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
05/30130592 DC : DRAFT MAR 2005 BS EN 15167-1 - GROUND GRANULATED BLASTFURNACE SLAG FOR USE IN CONCRETE, MORTAR AND GROUT - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY CRITERIA
UNI EN 13282-1 : 2013 HYDRAULIC ROAD BINDERS - PART 1: RAPID HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
PREN 494 : DRAFT 2010 FIBRE-CEMENT PROFILED SHEETS AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS
UNI CEN/TS 14754-1 : 2007 CURING COMPOUNDS - TEST METHODS - PART 1: DETERMINATION OF WATER RETENTION EFFICIENCY OF COMMON CURING COMPOUNDS
UNE-EN 14490:2013 Execution of special geotechnical works - Soil nailing
S.R. CEN/TR 16912:2016 GUIDELINES FOR A PROCEDURE TO SUPPORT THE EUROPEAN STANDARDIZATION OF CEMENTS
ISO 29581-2:2010 Cement Test methods Part 2: Chemical analysis by X-ray fluorescence
I.S. EN 196-6:2010 METHODS OF TESTING CEMENT - PART 6: DETERMINATION OF FINENESS
I.S. EN 13282-1:2013 HYDRAULIC ROAD BINDERS - PART 1: RAPID HARDENING HYDRAULIC ROAD BINDERS - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
UNE-EN 13282-2:2016 Hydraulic road binders - Part 2: Normal hardening hydraulic road binders - Composition, specifications and conformity criteria
UNE-EN 12004-2:2017 Adhesives for ceramic tiles - Part 2: Test methods
UNI EN 15368 : 2010 HYDRAULIC BINDER FOR NON-STRUCTURAL APPLICATIONS - DEFINITION, SPECIFICATIONS AND CONFORMITY CRITERIA
ISO 13270:2013 Steel fibres for concrete — Definitions and specifications
17/30354260 DC : 0 BS EN 12716 - EXECUTION OF SPECIAL GEOTECHNICAL WORKS - JET GROUTING
PREN 1504-3 : DRAFT 2015 PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND AVCP - PART 3: REPAIR CONCRETE AND MORTARS
UNI EN 15191 : 2010 PRECAST CONCRETE PRODUCTS - CLASSIFICATION OF GLASSFIBRE REINFORCED CONCRETE PERFORMANCE
DIN EN 13877-2:2013-06 CONCRETE PAVEMENTS - PART 2: FUNCTIONAL REQUIREMENTS FOR CONCRETE PAVEMENTS
DIN EN 13877-1:2013-06 CONCRETE PAVEMENTS - PART 1: MATERIALS
DIN EN 1992-1-1:2011-01 EUROCODE 2: DESIGN OF CONCRETE STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
DIN EN 14227-1:2013-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 1: CEMENT BOUND GRANULAR MIXTURES
BS EN 14891:2017 Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives. Requirements, test methods, assessment and verification of constancy of performance, classification and marking
BS EN 14618:2009 Agglomerated stone. Terminology and classification
BS EN 480-13:2015 Admixtures for concrete, mortar and grout. Test methods Reference masonry mortar for testing mortar admixtures
BS EN 1323:1999 Adhesives for tiles. Concrete slab for test
BS EN 14617-15:2005 Agglomerated stone. Test methods Determination of compressive strength
BS EN 15167-1:2006 Ground granulated blast furnace slag for use in concrete, mortar and grout Definitions, specifications and conformity criteria
BS EN 413-1:2011 Masonry cement Composition, specifications and conformity criteria
BS EN 197-4:2004 Cement Composition, specifications and conformity criteria for low early strength blastfurnace cements
BS EN 13101:2002 Steps for underground man entry chambers. Requirements, marking, testing and evaluation of conformity
CR 14245:2001 Guidelines for the application of EN 197-2 "Conformity Evaluation"
EN 1008:2002 Mixing water for concrete - Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete
EN 13286-49:2004 Unbound and hydraulically bound mixtures - Part 49: Accelerated swelling test for soil treated by lime and/or hydraulic binder
CEN/TR 16349:2012 Framework for a specification on the avoidance of a damaging Alkali-Silica Reaction (ASR) in concrete
EN 13101:2002 Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity
DIN EN 12004-2:2017-05 ADHESIVES FOR CERAMIC TILES - PART 2: TEST METHODS
DIN EN 13880-12:2003-11 HOT-APPLIED JOINT SEALANTS - PART 12: TEST METHOD FOR THE MANUFACTURE OF CONCRETE TEST BLOCKS FOR BOND TESTING (RECIPE METHODS)
DIN EN 14845-1:2007-09 Test methods for fibres in concrete - Part 1: Reference concretes
CEN/TR 15125:2005 Design, preparation and application of internal cement and/or lime plastering systems
EN 10298:2005 Steel tubes and fittings for on shore and offshore pipelines - Internal lining with cement mortar
EN 13364:2001 Natural stone test methods - Determination of the breaking load at dowel hole
DIN EN 450-2:2005-05 Fly ash for concrete - Part 2: Conformity evaluation
EN 13282-2:2015 Hydraulic road binders - Part 2: Normal hardening hydraulic road binders - Composition, specifications and conformity criteria
EN 13282-1:2013 Hydraulic road binders - Part 1: Rapid hardening hydraulic road binders - Composition, specifications and conformity criteria
DIN EN 545:2011-09 Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
DIN EN 10298:2005-12 Steel tubes and fittings for onshore and offshore pipelines - Internal lining with cement mortar
DIN EN 14227-12:2006-08 HYDRAULICALLY BOUND MIXTURES - SPECIFICATIONS - PART 12: SOIL TREATED BY SLAG
EN 12004-2:2017 Adhesives for ceramic tiles - Part 2: Test methods
DIN EN 450-1:2012-10 Fly ash for concrete - Part 1: Definition, specifications and conformity criteria

93/68/EEC : 1993 AMD 2 1998 COUNCIL DIRECTIVE 93/68/EEC OF 22.7.93 AMENDING DIRECTIVES 87/404/EEC, 88/378/EEC, 89/106/EEC, 89/336/EEC, 89/392/EEC, 89/686/EEC, 90/384/EEC, 90/385/EEC, 90/396/EEC, 91/263/EEC, 92/42/EEC AND 73/23/EEC
BS EN 13914-1:2016 Design, preparation and application of external rendering and internal plastering External rendering
BS EN 998-2:2016 Specification for mortar for masonry Masonry mortar
EN 196-7:2007 Methods of testing cement - Part 7: Methods of taking and preparing samples of cement
BS EN 1996-1-1 NA : 2005 UK NATIONAL ANNEX TO EUROCODE 6: DESIGN OF MASONRY STRUCTURES - PART 1-1: GENERAL RULES FOR REINFORCED AND UNREINFORCED MASONRY STRUCTURES
BS EN 196-2:2013 Method of testing cement Chemical analysis of cement
EN 196-2:2013 Method of testing cement - Part 2: Chemical analysis of cement
EN 196-5:2011 Methods of testing cement - Part 5: Pozzolanicity test for pozzolanic cement
BS EN 13914-2:2016 Design, preparation and application of external rendering and internal plastering Internal plastering
EN 197-2:2014 Cement - Part 2: Conformity evaluation
BS 8000-2.1:1990 Workmanship on building sites. Code of practice for concrete work Mixing and transporting concrete
BS 8000-2.2:1990 Workmanship on building sites. Code of practice for concrete work Sitework with in situ and precast concrete
89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
BS 8204-1(2003) : 2003 SCREEDS, BASES AND IN SITU FLOORINGS - PART 1: CONCRETE BASES AND CEMENTITIOUS LEVELLING SCREEDS TO RECEIVE FLOORINGS - CODE OF PRACTICE
BS EN 206-1:2000 Concrete Specification, performance, production and conformity
BS 8500-2(2006) : 2006 CONCRETE - COMPLEMENTARY BRITISH STANDARD TO BS EN 206-1 - PART 2: SPECIFICATION FOR CONSTITUENT MATERIALS AND CONCRETE
EN 15743:2010+A1:2015 Supersulfated cement - Composition, specifications and conformity criteria
ISO 9286:1997 Abrasive grains and crude Chemical analysis of silicon carbide
EN 933-9:2009+A1:2013 Tests for geometrical properties of aggregates - Part 9: Assessment of fines - Methylene blue test
BS EN 998-1:2016 Specification for mortar for masonry Rendering and plastering mortar
EN 14647:2005/AC:2006 CALCIUM ALUMINATE CEMENT - COMPOSITION, SPECIFICATIONS AND CONFORMITY CRITERIA
PD 6678:2005 Guide to the specification of masonry mortar
EN 196-1:2016 Methods of testing cement - Part 1: Determination of strength
AS ISO 13007.5:2020 Ceramic tiles - Grouts and adhesives Requirements, test methods, evaluation of conformity, classification and designation of liquid-applied waterproofing membranes for use beneath ceramic tiling bonded with adhesives
BS EN 196-7:2007 Methods of testing cement Methods of taking and preparing samples of cement
EN 14216:2015 Cement - Composition, specifications and conformity criteria for very low heat special cements
EN 13639:2017 Determination of total organic carbon in limestone
EN 413-1:2011 Masonry cement - Part 1: Composition, specifications and conformity criteria
EN 451-1:2017 Method of testing fly ash - Part 1: Determination of free calcium oxide content
EN 450-1:2012 Fly ash for concrete - Part 1: Definition, specifications and conformity criteria
EN 206-1:2000/A2:2005 CONCRETE - PART 1: SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
ISO 10694:1995 Soil quality Determination of organic and total carbon after dry combustion (elementary analysis)
BS EN 196-1:2016 Methods of testing cement Determination of strength
BS EN 13813:2002 Screed material and floor screeds. Screed material. Properties and requirements
EN 196-8:2010 Methods of testing cement - Part 8: Heat of hydration - Solution method
EN 196-3:2016 Methods of testing cement - Part 3: Determination of setting times and soundness
EN 196-9:2010 Methods of testing cement - Part 9: Heat of hydration - Semi-adiabatic method
ISO 9277:2010 Determination of the specific surface area of solids by gas adsorption — BET method

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.