EN 60255-5:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
03-01-2014
04-19-2001
INTRODUCTION
1 Scope and object
2 Normative references
3 Definitions
4 Insulation coordination
4.1 Basic principles
4.2 Voltages and voltage ratings
4.3 Time under voltage stress
4.4 Pollution
4.5 Information to be found on the relay or in the
operating structures
4.6 Insulation material
5 Dimensioning requirements and rules
5.1 Dimensioning of clearances
5.2 Dimensioning of creepage distances
5.3 Requirements for design of solid insulation
6 Tests and measurements
6.1 Tests
6.2 Measurements
Annex A (informative) Nominal voltages of supply systems
Annex B (informative) Altitude correction factors
Annex C (informative) Guidance for impulse voltage tests
Annex D (informative) Measurement of creepage distances and
clearances
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
Lays down general requirements for the insulation coordination of measuring relays and protection equipment. Gives guidance for the selection of clearances and creepage distances and other aspects related to the insulation of measuring relays and protection equipment; specifies requirements for voltage tests and insulation resistance measurement.
| Committee |
CLC/TC 95X
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| CEI EN 60255-5 : 2001 | Identical |
| PN EN 60255-5 : 2005 | Identical |
| UNE-EN 60255-5:2002 | Identical |
| I.S. EN 60255-5:2001 | Identical |
| DIN EN 60255-5 : 2001 | Identical |
| NF EN 60255-5 : 2001 | Identical |
| NBN EN 60255-5 : 2001 | Identical |
| VDE 0435-130 : 2001 | Identical |
| NEN EN IEC 60255-5 : 2001 | Identical |
| BS EN 60255-5:2001 | Identical |
| SN EN 60255-5 : 2001 | Identical |
| IEC 60255-5:2000 | Identical |
| BS EN 50216-2:2002 | Power transformers and reactor fittings Gas and oil actuated relay for liquid immersed transformers and reactors with conservator |
| BS EN 60143-4:2010 | Series capacitors for power systems Thyristors controlled series capacitors |
| BS EN 50216-1:2002 | Power transformers and reactor fittings General |
| I.S. EN 60143-4:2010 | SERIES CAPACITORS FOR POWER SYSTEMS - PART 4: THYRISTOR CONTROLLED SERIES CAPACITORS |
| I.S. EN 60044-8:2002 | INSTRUMENT TRANSFORMERS - PART 8: ELECTRONIC CURRENT TRANSFORMERS |
| EN 50216-2 : 2002 AMD 1 2002 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 2: GAS AND OIL ACTUATED RELAY FOR LIQUID IMMERSED TRANSFORMERS AND REACTORS WITH CONSERVATOR |
| EN 50216-1:2002 | Power transformer and reactor fittings - Part 1: General |
| BS EN 60044-8:2002 | Instrument transformers Electronic current transformers |
| CEI EN 50216-1 : 2002 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 1: GENERAL |
| CEI EN 60143-4 : 2012 | SERIES CAPACITORS FOR POWER SYSTEMS - PART 4: THYRISTOR CONTROLLED SERIES CAPACITORS |
| I.S. EN 60143-2:2013 | SERIES CAPACITORS FOR POWER SYSTEMS - PART 2: PROTECTIVE EQUIPMENT FOR SERIES CAPACITOR BANKS (IEC 60143-2:2012 (EQV)) |
| I.S. EN 50216-2:2002 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 2: GAS AND OIL ACTUATED RELAY FOR LIQUID IMMERSED TRANSFORMERS AND REACTORS WITH CONSERVATOR |
| BS EN 60143-2:2013 | Series capacitors for power systems Protective equipment for series capacitor banks |
| CEI EN 60143-2 : 2014 | SERIES CAPACITORS FOR POWER SYSTEMS - PART 2: PROTECTIVE EQUIPMENT FOR SERIES CAPACITOR BANKS |
| CEI EN 60044-8 : 2004 | INSTRUMENT TRANSFORMERS - PART 8: ELECTRONIC CURRENT TRASFORMERS |
| 04/30117565 DC : DRAFT AUG 2004 | EN 50438 - REQUIREMENTS FOR THE CONNECTION OF MICRO-COGENERATORS IN PARALLEL WITH PUBLIC LOW-VOLTAGE DISTRIBUTION NETWORKS |
| I.S. EN 50216-1:2002 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 1: GENERAL |
| EN 60143-4 : 2010 | SERIES CAPACITORS FOR POWER SYSTEMS - PART 4: THYRISTOR CONTROLLED SERIES CAPACITORS |
| EN 60143-2:2013 | Series capacitors for power systems - Part 2: Protective equipment for series capacitor banks |
| EN 60044-8:2002 | Instrument transformers - Part 8: Electronic current transformers |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| IEC 60255-21-2:1988 | Electrical relays - Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment - Section Two: Shock and bump tests |
| IEC 60255-22-1:2007 | Measuring relays and protection equipment - Part 22-1: Electrical disturbance tests - 1 MHz burst immunity tests |
| IEC 60255-25:2000 | Electrical relays - Part 25: Electromagnetic emission tests for measuring relays and protection equipment |
| IEC 60255-3:1989 | Electrical relays - Part 3: Single input energizing quantity measuring relays with dependent or independent time |
| IEC 60255-7:1991 | Electrical relays - Part 7: Test and measurement procedures for electromechanical all-or-nothing relays |
| IEC 60255-10:1979 | Electrical relays. Part 10: Application of the IEC Quality Assessment System for Electronic Components to all-or-nothing relays |
| IEC 60255-16:1982 | Electrical relays - Part 16: Impedance measuring relays |
| IEC 60255-21-3:1993 | Electrical relays - Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment - Section 3: Seismic tests |
| IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
| IEC 60255-24:2013 | Measuring relays and protection equipment - Part 24: Common format for transient data exchange (COMTRADE) for power systems |
| IEC 60255-9:1979 | Electrical relays. Part 9: Dry reed make contact units |
| IEC 60255-11:2008 | Measuring relays and protection equipment - Part 11: Voltage dips, short interruptions, variations and ripple on auxiliary power supply port |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| IEC 60255-15:1981 | Electrical relays. Part 15: Endurance tests for electrical relay contacts - Specification for the characteristics of test equipment |
| IEC 60255-19:1983 | Electrical relays. Part 19: Sectional specification: Electromechanical all-or-nothing relays of assessed quality |
| IEC 61180-2:1994 | High-voltage test techniques for low-voltage equipment - Part 2: Test equipment |
| IEC 60255-19-1:1983 | Electrical relays. Part 19: Blank detail specification: Electromechanical all-or-nothing relays of assessed quality - Test schedules 1, 2 and 3 |
| IEC 60255-22-6:2001 | Electrical relays - Part 22-6: Electrical disturbance tests for measuring relays and protection equipment - Immunity to conducted disturbances induced by radio frequency fields |
| IEC 60255-22-3:2007 | Measuring relays and protection equipment - Part 22-3: Electrical disturbance tests - Radiated electromagnetic field immunity |
| IEC 60255-14:1981 | Electrical relays. Part 14: Endurance tests for electrical relay contacts - Preferred values for contact loads |
| IEC 60255-1-00:1975 | Electrical relays. All-or-nothing electrical relays. *Note.-This publication supersedes IEC 255-1 (1967) and 255-2 (1969) |
| IEC 60255-6:1988 | Electrical relays - Part 6: Measuring relays and protection equipment |
| IEC 60255-22-2:2008 | Measuring relays and protection equipment - Part 22-2: Electrical disturbance tests - Electrostatic discharge tests |
| IEC 60255-21-1:1988 | Electrical relays - Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment - Section One: Vibration tests (sinusoidal) |
| IEC 60255-8:1990 | Electrical relays - Part 8: Thermal electrical relays |
| IEC 60255-18:1982 | Electrical relays. Part 18: Dimensions for general purpose all-or-nothing relays |
| IEC 60255-23:1994 | Electrical relays - Part 23: Contact performance |
| IEC 61180-1:1992 | High-voltage test techniques for low voltage equipment - Part 1: Definitions, test and procedure requirements |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 60050-448:1995 | International Electrotechnical Vocabulary (IEV) - Part 448: Power system protection |
| IEC 60255-12:1980 | Electrical relays - Part 12: Directional relays and power relays with two input energizing quantities |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 60255-13:1980 | Electrical relays - Part 13: Biased (percentage) differential relays |
| IEC 60255-22-4:2008 | Measuring relays and protection equipment - Part 22-4: Electrical disturbance tests - Electrical fast transient/burst immunity test |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.