• There are no items in your cart

EN 60754-2:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Test on gases evolved during combustion of materials from cables - Part 2: Determination of acidity (by pH measurement) and conductivity
Superseded date

03-19-2020

Published date

04-18-2014

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Test method principle
5 Test apparatus
6 Test specimen
7 Test procedure
8 Evaluation of the test results
9 Performance requirement
10 Test report
Annex A (informative) - Recommended performance
        requirements
Bibliography
Annex ZA (normative) - Normative references to international
         Publications with their corresponding
         European publications

IEC 60754-2:2011 specifies the apparatus and procedure for the determination of the potential corrosivity of gases evolved during the combustion of materials taken from electric or optical fibre cable constructions by measuring the acidity (pH) and conductivity of an aqueous solution resulting from the gases evolved during the combustion. The general method specified in this standard is intended for the testing of individual components used in a cable construction. Formulae are given for the calculation of a weighted value for a combination of materials found in a specified cable. The use of this method will enable the verification of relevant requirements for either individual components or combined components of a cable construction stated in the appropriate cable specification. A simplified method is included for the testing of individual components where it is required only to demonstrate compliance with a stated performance requirement for quality control purposes. The significant technical changes with respect to the previous edition are as follows: - improved definition of safety requirements relating to capture of gases; - introduction of guidance on the preparation of test specimens for more even combustion; - better expression of tolerances and precision; - clarification of the conductivity and acidity functions; - improved definition of the heating procedure; - greater precision in the definition of the test temperature for the determination of pH value and conductivity; - correction of the formulae for the calculation of the test results. IEC 60754-2:2011 has the status of a group safety publication in accordance with IEC Guide 104.

Committee
CLC/TC 20
DevelopmentNote
Supersedes EN 50267-1, EN 50267-2-1, EN 50267-2-2 and EN 50267-2-3. (04/2014)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy
Supersedes

UNE-EN 50290-2-33:2016 Communication cables - Part 2-33: Common design rules and construction - Polyethylene insulation compounds for multi element metallic cables for indoor installation (data cable)
CEI EN 50290-2-36 : 1ED 2017 COMMUNICATION CABLES - PART 2-36: COMMON DESIGN RULES AND CONSTRUCTION - CROSSLINKED SILICONE RUBBER INSULATION COMPOUND
CEI EN 50290-2-33 : 1ED 2017 COMMUNICATION CABLES - PART 2-33: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION COMPOUNDS FOR MULTI ELEMENT METALLIC CABLES FOR INDOOR INSTALLATION (DATA CABLE)
BS EN 50575 : 2014 POWER, CONTROL AND COMMUNICATION CABLES - CABLES FOR GENERAL APPLICATIONS IN CONSTRUCTION WORKS SUBJECT TO REACTION TO FIRE REQUIREMENTS
EN 50290-2-37:2016 Communication cables - Part 2-37: Common design rules and construction - Polyethylene insulation for coaxial cables
EN 61158-2:2014 Industrial communication networks - Fieldbus specifications - Part 2: Physical layer specification and service definition
EN 50575:2014/A1:2016 POWER, CONTROL AND COMMUNICATION CABLES - CABLES FOR GENERAL APPLICATIONS IN CONSTRUCTION WORKS SUBJECT TO REACTION TO FIRE REQUIREMENTS
EN 60702-1:2002/A1:2015 MINERAL INSULATED CABLES AND THEIR TERMINATIONS WITH A RATED VOLTAGE NOT EXCEEDING 750 V - PART 1: CABLES (IEC 60702-1:2002/A1:2015)
I.S. EN 60702-1:2002 MINERAL INSULATED CABLES AND THEIR TERMINATIONS WITH A RATED VOLTAGE NOT EXCEEDING 750 V - PART 1: CABLES
I.S. EN 50575:2014 POWER, CONTROL AND COMMUNICATION CABLES - CABLES FOR GENERAL APPLICATIONS IN CONSTRUCTION WORKS SUBJECT TO REACTION TO FIRE REQUIREMENTS
PREN 50626-1 : DRAFT 2017 CONDUIT SYSTEMS BURIED UNDERGROUND FOR THE PROTECTION AND MANAGEMENT OF INSULATED ELECTRICAL CABLES OR COMMUNICATION CABLES - PART 1: GENERAL REQUIREMENTS
I.S. EN 50290-2-37:2016 COMMUNICATION CABLES - PART 2-37: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION FOR COAXIAL CABLES
CEI EN 50290-2-37 : 1ED 2017 COMMUNICATION CABLES - PART 2-37: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION FOR COAXIAL CABLES
I.S. EN 50290-2-33:2016 COMMUNICATION CABLES - PART 2-33: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION COMPOUNDS FOR MULTI ELEMENT METALLIC CABLES FOR INDOOR INSTALLATION (DATA CABLE)
CEI EN 50290-2-38 : 1ED 2017 COMMUNICATION CABLES - PART 2-38: COMMON DESIGN RULES AND CONSTRUCTION - POLYPROPYLENE INSULATION FOR COAXIAL CABLES
BS EN 50290-2-38:2016 Communication cables Common design rules and construction. Polypropylene insulation for coaxial cables
BS EN 50290-2-33:2016 Communication cables Common design rules and construction. Polyethylene insulation compounds for multi element metallic cables for indoor installation (data cable)
17/30348256 DC : 0 BS EN 13501-6 - FIRE CLASSIFICATION OF CONSTRUCTION PRODUCTS AND BUILDING ELEMENTS - PART 6: CLASSIFICATION USING DATA FROM REACTION TO FIRE TESTS ON ELECTRIC CABLES
I.S. EN 50290-2-36:2016 COMMUNICATION CABLES - PART 2-36: COMMON DESIGN RULES AND CONSTRUCTION - CROSSLINKED SILICONE RUBBER INSULATION COMPOUND
BS EN 50290-2-37:2016 Communication cables Common design rules and construction. Polyethylene insulation for coaxial cables
UNE-EN 50290-2-36:2016 Communication cables - Part 2-36: Common design rules and construction - Crosslinked Silicone rubber insulation compound
I.S. EN 61158-2:2014 INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 2: PHYSICAL LAYER SPECIFICATION AND SERVICE DEFINITION
I.S. EN 50290-2-38:2016 COMMUNICATION CABLES - PART 2-38: COMMON DESIGN RULES AND CONSTRUCTION - POLYPROPYLENE INSULATION FOR COAXIAL CABLES
BS EN 60702-1 : 2002 MINERAL INSULATED CABLES AND THEIR TERMINATIONS WITH A RATED VOLTAGE NOT EXCEEDING 750 V - PART 1: CABLES
PREN 13501-6 : DRAFT 2017 FIRE CLASSIFICATION OF CONSTRUCTION PRODUCTS AND BUILDING ELEMENTS - PART 6: CLASSIFICATION USING DATA FROM REACTION TO FIRE TESTS ON ELECTRIC CABLES
UNE-EN 50290-2-38:2016 Communication cables - Part 2-38: Common design rules and construction - Polypropylene insulation for coaxial cables
EN 50290-2-33:2016 Communication cables - Part 2-33: Common design rules and construction - Polyethylene insulation compounds for multi element metallic cables for indoor installation (data cable)
DIN EN 61158-2:2015-02 INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 2: PHYSICAL LAYER SPECIFICATION AND SERVICE DEFINITION (IEC 61158-2:2014)
UNE-EN 50575:2015 Power, control and communication cables - Cables for general applications in construction works subject to reaction to fire requirements
UNE-EN 50290-2-37:2016 Communication cables - Part 2-37: Common design rules and construction - Polyethylene insulation for coaxial cables
BS EN 61158-2:2014 Industrial communication networks. Fieldbus specifications Physical layer specification and service definition
EN 50290-2-36:2016 Communication cables - Part 2-36: Common design rules and construction - Crosslinked Silicone rubber insulation compound
EN 50290-2-38 : 2016 Communication cables - Part 2-38: Common design rules and construction - Polypropylene insulation for coaxial cables

IEC 60695-5-1:2002 Fire hazard testing - Part 5-1: Corrosion damage effects of fire effluent - General guidance
ISO 1042:1998 Laboratory glassware One-mark volumetric flasks
EN ISO 1042 : 1999 LABORATORY GLASSWARE - ONE-MARK VOLUMETRIC FLASKS
IEC GUIDE 104:2010 The preparation of safety publications and the use of basic safety publications and group safety publications
ISO 3696:1987 Water for analytical laboratory use — Specification and test methods
EN ISO 3696:1995 Water for analytical laboratory use - Specification and test methods (ISO 3696:1987)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.