• There are no items in your cart

EN 60793-1-32:2010

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Optical fibres - Part 1-32: Measurement methods and test procedures - Coating strippability
Superseded date

02-03-2022

Published date

10-01-2010

FOREWORD
1 Scope
2 Normative references
3 Apparatus
4 Specimen preparation
5 Procedure
6 Calculations
7 Documentation
8 Specification information
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

IEC 60793-1-32:2010(E) is intended primarily for testing either fibres as produced by a fibre manufacturer or subsequently overcoated (tight buffered) using various polymers. The test can be performed either on fibres as produced or after exposure to various environments. This test applies to A1, A2, A3, B and C fibres. This edition has been modified to include current practices in the market place.

Committee
CLC/TC 86A
DevelopmentNote
Partially supersedes EN 188000 (01/2004) Supersedes UNE EN 188000. (01/2012)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy
Supersedes

BS EN 60794-1-21:2015 Optical fibre cables Generic specification. Basic optical cable test procedures. Mechanical tests methods
I.S. EN 187105:2002 SINGLE MODE OPTICAL CABLE (DUCT/DIRECT BURIED INSTALLATION)
I.S. EN 60793-2-10:2017 OPTICAL FIBRES - PART 2-10: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A1 MULTIMODE FIBRE
EN 60793-1-1:2017 Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance
EN 60794-3:2015 Optical fibre cables - Part 3: Sectional specification - Outdoor cables
EN 60793-2-60:2008 Optical fibres - Part 2-60: Product specifications - Sectional specification for category C single-mode intraconnection fibres
UNE-EN 60793-1-1:2017 Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance
UNE-EN 60793-1-53:2014 Optical fibres - Part 1-53: Measurement methods and test procedures - Water immersion tests
BS EN 187105:2002 Single mode optical cable (duct/direct buried installation)
BS EN 60793-2-60:2008 Optical fibres Product specifications. Sectional specification for category C single-mode intraconnection fibres
BS EN 60793-1-53:2014 Optical fibres Measurement methods and test procedures. Water immersion tests
I.S. EN 60794-1-21:2015 OPTICAL FIBRE CABLES - PART 1-21: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - MECHANICAL TESTS METHODS
BS EN 60793-2-50:2016 Optical fibres Product specifications. Sectional specification for class B single-mode fibres
UNE-EN 60793-1-50:2015 Optical fibres - Part 1-50: Measurement methods - Damp heat (steady state) tests
I.S. EN 60794-3:2002 OPTICAL FIBRE CABLES - PART 3: SECTIONAL SPECIFICATION - OUTDOOR CABLES
CEI EN 60793-2-60 : 2009 OPTICAL FIBRES - PART 2-60: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY C SINGLE-MODE INTRACONNECTION FIBRES
I.S. EN 60793-2-50:2016 OPTICAL FIBRES - PART 2-50: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CLASS B SINGLE-MODE FIBRES
BS EN 60793-1-1:2017 Optical fibres Measurement methods and test procedures. General and guidance
BS EN 60794-3-11:2010 Optical fibre cables Outdoor cables. Product specification for duct, directly buried and lashed aerial single-mode optical fibre telecommunication cables
CEI EN 60793-1-1 : 2010 OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE
BS EN 60793-1-50:2015 Optical fibres Measurement methods. Damp heat (steady state) tests
I.S. EN 60793-2-60:2008 OPTICAL FIBRES - PART 2-60: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY C SINGLE-MODE INTRACONNECTION FIBRES
BS EN 60794-3:2015 Optical fibre cables Sectional specification. Outdoor cables
EN 60793-2-10:2017 Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres
EN 60794-1-21:2015 Optical fibre cables - Part 1-21: Generic specification - Basic optical cable test procedures - Mechanical tests methods
BS EN 60793-2-10:2017 Optical fibres Product specifications. Sectional specification for category A1 multimode fibres
CEI EN 60793-1-53 : 2014 OPTICAL FIBRES - PART 1-53: MEASUREMENT METHODS AND TEST PROCEDURES - WATER IMMERSION TESTS
I.S. EN 60793-1-50:2015 OPTICAL FIBRES - PART 1-50: MEASUREMENT METHODS - DAMP HEAT (STEADY STATE) TESTS
I.S. EN 60793-1-1:2017 OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE
I.S. EN 60793-1-53:2014 OPTICAL FIBRES - PART 1-53: MEASUREMENT METHODS AND TEST PROCEDURES - WATER IMMERSION TESTS
EN 60794-3-11:2010 Optical fibre cables - Part 3-11: Outdoor cables - Product specification for duct, directly buried and lashed aerial single-mode optical fibre telecommunication cables
EN 187105:2002 Single mode optical cable (duct/direct buried installation)
EN 60793-1-53:2014 Optical fibres - Part 1-53: Measurement methods and test procedures - Water immersion tests
EN 60793-2-50:2016 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres
EN 60793-1-50:2015 Optical fibres - Part 1-50: Measurement methods and test procedures - Damp heat (steady state) tests

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.