Connectors for electrical and electronic equipment - Product requirements - Part 2-111: Circular connectors - Detail specification for power connectors with M12 screw-locking

Published date

03-09-2018

Publisher

European Committee for Standards - Electrical

FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Technical information
5 Dimensional information
6 Characteristics
7 Test schedule
Annex A (informative) - Diameter of the female
        connector body and orientation of coding
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

IEC 61076-2-111:2017 specifies 4 to 6-way circular connectors with M12 screw-locking with current ratings up to 16 A and voltage ratings of 63 V or 630 V, that are typically used for power supply and power applications in industrial premises. These connectors consist of both, fixed and free connectors either rewireable or non-rewireable, with M12 screw-locking. Male connectors have round contacts Ø1,0 mm and Ø1,5 mm.The different codings provided by this document prevent the mating of accordingly coded male or female connectors to any other similarly sized interfaces, covered by other standards and the cross-mating between the different codings provided by this document.M12 is the dimension of the thread of the screw locking mechanism of these circular connectors.Keywords: Connectors, Circular Connectors, M12.

Committee	CLC/SR 48B
DocumentType	Standard
PublisherName	European Committee for Standards - Electrical
Status	Current

Standards	Relationship
UNE-EN IEC 61076-2-111:2018	Identical
IEC 61076-2-111:2017	Identical
CEI EN IEC 61076-2-111 : 2018	Identical
DIN EN IEC 61076-2-111 : 2018-10	Identical
VDE 0687-76-2-111: 2018-10	Identical
BS EN IEC 61076-2-111:2018	Identical

IEC 61076-1:2006	Connectors for electronic equipment - Product requirements - Part 1: Generic specification
EN 60352-2:2006/A1:2013	SOLDERLESS CONNECTIONS - PART 2: CRIMPED CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE
IEC 60352-3:1993	Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance
EN 60512-19-3:1997	Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 19: Chemical resistance tests - Section 3: Test 19c - Fluid resistance
IEC 60512-11-4:2002	Connectors for electronic equipment - Tests and measurements - Part 11-4: Climatic tests - Test 11d: Rapid change of temperature
IEC 60512-11-9:2002	Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat
IEC 60512-11-10:2002	Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold
EN 60512-11-9:2002	Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat
EN 60068-2-60:2015	Environmental testing - Part 2-60: Tests - Test Ke: Flowing mixed gas corrosion test
IEC 61984:2008	Connectors - Safety requirements and tests
IEC 60352-6:1997	Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance
IEC 60512-3-1:2002	Connectors for electronic equipment - Tests and measurements - Part 3-1: Insulation tests - Test 3a: Insulation resistance
IEC 60068-1:2013	Environmental testing - Part 1: General and guidance
IEC 60512-9-2:2011	Connectors for electronic equipment - Tests and measurements - Part 9-2: Endurance tests - Test 9b: Electrical load and temperature
EN 60512-11-1:1999	Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 11: Climatic tests - Section 1: Test 11a - Climatic sequence
IEC 60512-13-5:2006	Connectors for electronic equipment - Tests and measurements - Part 13-5: Mechanical operation tests - Test 13e: Polarizing and keying method
IEC 60068-2-60:2015 RLV	Environmental testing - Part 2-60: Tests - Test Ke: Flowing mixed gas corrosion test
EN 60352-3:1994	Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance
EN 60512-11-12 : 2002	Connectors for electronic equipment - Tests and measurements - Part 11-12: Climatic tests - Test 11m: Damp heat, cyclic
EN ISO 1302 : 2002	GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INDICATION OF SURFACE TEXTURE IN TECHNICAL PRODUCT DOCUMENTATION (ISO 1302:2002)
EN 60068-1:2014	Environmental testing - Part 1: General and guidance
ISO 11469:2016	Plastics — Generic identification and marking of plastics products
IEC 60512-13-2:2006	Connectors for electronic equipment - Tests and measurements - Part 13-2: Mechanical operation tests - Test 13b: Insertion and withdrawal forces
EN 60352-6:1997	Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance
IEC 60512-5-1:2002	Connectors for electronic equipment - Tests and measurements - Part 5-1: Current-carrying capacity tests - Test 5a: Temperature rise
EN ISO 11469:2016	Plastics - Generic identification and marking of plastics products (ISO 11469:2016)
EN 61076-1:2006	Connectors for electronic equipment - Product requirements - Part 1: Generic specification
IEC 60512-16-5:2008	Connectors for electronic equipment - Tests and measurements - Part 16-5: Mechanical tests on contacts and terminations - Test 16e: Gauge retention force (resilient contacts)
EN 60512-5-1 : 2002	Connectors for electronic equipment - Tests and measurements - Part 5-1: Current-carrying capacity tests - Test 5a: Temperature rise
EN 60512-6-4:2002	Connectors for electronic equipment - Tests and measurements - Part 6-4: Dynamic stress tests - Test 6d: Vibration (sinusoidal)
IEC 60999-1:1999	Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
EN 60512-13-2 : 2006 COR 2006	CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 13-2: MECHANICAL OPERATION TESTS - TEST 13B: INSERTION AND WITHDRAWAL FORCES
EN 60352-5:2012/AC:2014	SOLDERLESS CONNECTIONS - PART 5: PRESS-IN CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE (IEC 60352-5:2012)
ISO 1302:2002	Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
EN 60512-11-7:2003	Connectors for electronic equipment - Tests and measurements - Part 11- 7: Climatic tests - Test 11g: Flowing mixed gas corrosion test
EN 60512-1-2:2002	Connectors for electronic equipment - Tests and measurements - Part 1-2: General examination - Test 1b: Examination of dimension and mass
EN 60512-9-2:2012	Connectors for electronic equipment - Tests and measurements - Part 9-2: Endurance tests - Test 9b: Electrical load and temperature
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV	Degrees of protection provided by enclosures (IP Code)
IEC 60512-1-1:2002	Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination
IEC 60352-5:2012	Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance
EN 60512-16-5:2008	Connectors for electronic equipment - Tests and measurements - Part 16-5: Mechanical tests on contacts and terminations - Test 16e: Gauge retention force (resilient contacts)
IEC 60512-11-1:1995	Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 11: Climatic tests - Section 1: Test 11a - Climatic sequence
IEC 60512-2-1:2002	Connectors for electronic equipment - Tests and measurements - Part 2-1: Electrical continuity and contact resistance tests - Test 2a: Contact resistance - Millivolt level method
IEC 60512-9-1:2010	Connectors for electronic equipment - Tests and measurements - Part 9-1: Endurance tests - Test 9a: Mechanical operation
IEC 60512-11-7:2003	Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests - Test 11g: Flowing mixed gas corrosion test
EN 60512-3-1:2002	Connectors for electronic equipment - Tests and measurements - Part 3-1: Insulation tests - Test 3a: Insulation resistance
EN 60664-1:2007	Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
IEC 60512-19-3:1997	Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 19: Chemical resistance tests - Section 3: Test 19c - Fluid resistance
IEC 60512-11-12:2002	Connectors for electronic equipment - Tests and measurements - Part 11-12: Climatic tests - Test 11m: Damp heat, cyclic
EN 60512-11-10:2002	Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold
IEC 60512-4-1:2003	Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - Test 4a: Voltage proof
EN 62197-1 : 2006	CONNECTORS FOR ELECTRONIC EQUIPMENT - QUALITY ASSESSMENT REQUIREMENTS - PART 1: GENERIC SPECIFICATION
IEC 60352-2:2006+AMD1:2013 CSV	Solderless connections - Part 2: Crimped connections - Generalrequirements, test methods and practical guidance
EN 60512-13-5:2006/corrigendum Dec. 2006	CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 13-5: MECHANICAL OPERATION TESTS - TEST 13E: POLARIZING AND KEYING METHOD
EN 60999-1:2000	Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm² up to 35 mm² (included)
EN 60352-4:1994/A1:2000	SOLDERLESS CONNECTIONS - PART 4: SOLDERLESS NON-ACCESSIBLE INSULATION DISPLACEMENT CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE
IEC 62197-1:2006	Connectors for electronic equipment - Quality assessment requirements - Part 1: Generic specification
EN 61984:2009	Connectors - Safety requirements and tests
EN 60529:1991/AC:2016-12	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN 60512-4-1:2003	Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - Test 4a: Voltage proof
EN 60352-7:2002	Solderless connections - Part 7: Spring clamp connections - General requirements, test methods and practical guidance
EN 60512-1-1:2002	Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination
EN 60512-6-3:2002	Connectors for electronic equipment - Tests and measurements - Part 6-3: Dynamic stress tests - Test 6c: Shock
IEC 60512-6-4:2002	Connectors for electronic equipment - Tests and measurements - Part 6-4: Dynamic stress tests - Test 6d: Vibration (sinusoidal)
IEC 60664-1:2007	Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
IEC 60050-581:2008	International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
IEC 60512-1-2:2002	Connectors for electronic equipment - Tests and measurements - Part 1-2: General examination - Test 1b: Examination of dimension and mass
EN 60512-9-1 : 2010	Connectors for electronic equipment - Tests and measurements - Part 9-1: Endurance tests - Test 9a: Mechanical operation
IEC 60352-7:2002	Solderless connections - Part 7: Spring clamp connections - General requirements, test methods and practical guidance
EN 60512-11-4:2002	Connectors for electronic equipment - Tests and measurements - Part 11-4: Climatic tests - Test 11d: Rapid change of temperature
EN 60512-2-1:2002	Connectors for electronic equipment - Tests and measurements - Part 2-1: Electrical continuity and contact resistance tests - Test 2a: Contact resistance - Millivolt level method