EN ISO 11963:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
09-12-2019
11-15-2012
Foreword
1 Scope
2 Normative references
3 Composition
4 Requirements
5 Test methods
6 Reaction to fire
7 Use in contact with food
8 Retest and rejection
Annex A (normative) - Determination of change in dimensions
at elevated temperature (shrinkage)
ISO 11963:2012 specifies the requirements for solid, flat extruded sheets of polycarbonate (PC) for general applications. It applies specifically to sheets made of poly(p,p′-isopropylidenediphenyl carbonate). The sheets may be coloured or colourless, and they may be transparent, translucent or opaque. The sheets may also have a special weather-protective layer on one or both surfaces.ISO 11963:2012 applies only to thicknesses equal to or greater than 1,5 mm.
| Committee |
CEN/TC 249
|
| DevelopmentNote |
Supersedes PREN ISO 11963. (12/2012)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNE-EN ISO 11963:2013 | Identical |
| UNI EN ISO 11963 : 2013 | Identical |
| SN EN ISO 11963 : 2013 | Identical |
| BS EN ISO 11963:2012 | Identical |
| ISO 11963:2012 | Identical |
| NF EN ISO 11963 : 2013 | Identical |
| NBN EN ISO 11963 : 2013 | Identical |
| NEN EN ISO 11963 : 2012 | Identical |
| NS EN ISO 11963 : 2012 | Identical |
| I.S. EN ISO 11963:2012 | Identical |
| PN EN ISO 11963 : 2013 | Identical |
| ONORM EN ISO 11963 : 2013 | Identical |
| DIN EN ISO 11963:2013-03 | Identical |
| DIN EN 15860 E : 2012 | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| UNI EN 15860 : 2010 | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| 16/30317348 DC : 0 | BS EN 15860 - PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| PREN 15860 : DRAFT 2016 | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| UNE-EN 15860:2011 | Plastics - Thermoplastic semi-finished products for machining - Requirements and test methods |
| DIN EN 15860:2016-07 (Draft) | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| BS EN 15860:2010 | Plastics. Thermoplastic semi-finished products for machining. Requirements and test methods |
| EN 15860:2010 | Plastics - Thermoplastic semi-finished products for machining - Requirements and test methods |
| I.S. EN 15860:2010 | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| ISO 75-1:2013 | Plastics Determination of temperature of deflection under load Part 1: General test method |
| ISO 4892-1:2016 | Plastics Methods of exposure to laboratory light sources Part 1: General guidance |
| ISO 13468-1:1996 | Plastics Determination of the total luminous transmittance of transparent materials Part 1: Single-beam instrument |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 11359-2:1999 | Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 1482:2011 | Slotted countersunk (flat) head tapping screws |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 877-1:2009 | Plastics — Methods of exposure to solar radiation — Part 1: General guidance |
| ISO 489:1999 | Plastics Determination of refractive index |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 877-3:2009 | Plastics Methods of exposure to solar radiation Part 3: Intensified weathering using concentrated solar radiation |
| ISO 2859-10:2006 | Sampling procedures for inspection by attributes Part 10: Introduction to the ISO 2859 series of standards for sampling for inspection by attributes |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 7391-1:2006 | Plastics Polycarbonate (PC) moulding and extrusion materials Part 1: Designation system and basis for specifications |
| ISO 877-2:2009 | Plastics — Methods of exposure to solar radiation — Part 2: Direct weathering and exposure behind window glass |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.