EN ISO 13856-3:2013
Current
Current
The latest, up-to-date edition.
Safety of machinery - Pressure-sensitive protective devices - Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices (ISO 13856-3:2013)
Published date
07-24-2013
Publisher
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements for design and testing
5 Marking
6 Information for selection and use
7 Verification of requirements
Annex A (normative) - Timing diagrams for pressure-sensitive
bumpers, plates, wires and similar devices with/without
reset
Annex B (informative) - Device characteristics - Explanatory
remarks and recommendations
Annex C (informative) - Design guidance
Annex D (informative) - Application guidance
Annex E (informative) - Commissioning and inspection
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2006/42/EC
Bibliography
ISO 13856-3:2013 establishes general principles and specifies requirements for the design and testing of those pressure-sensitive protective devices, with or without an external reset facility, that are not specified in either ISO 13856‑1 or ISO 13856‑2, and the majority of which are produced for specific applications and are not available as "off-the-shelf" items.ISO 13856-3:2013 also gives specific requirements for the following pressure-sensitive protective devices: pressure-sensitive bumpers; pressure-sensitive plates; pressure-sensitive wires (trip wires).It deals with the design of a pressure-sensitive device with regard to safety and reliability rather than its suitability for particular applications.It is not applicable to specifying the dimensions of pressure-sensitive protective devices in relation to any particular application, or stopping devices according to IEC 60204‑1 used for the normal operation, including emergency stopping of machinery.While requirements are given for the immunity of the device to electromagnetic disturbances, these are not intended to cover all aspects of electromagnetic compatibility (EMC).
| Committee |
CEN/TC 114
|
| DevelopmentNote |
Supersedes PREN ISO 13856-3 & EN 1760-3. (08/2013)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| UNE-EN ISO 13856-3:2013 | Identical |
| NS EN ISO 13856-3 : 2013 | Identical |
| DIN EN ISO 13856-3:2013-12 | Identical |
| SS-EN ISO 13856-3 : 2013 | Identical |
| ISO 13856-3:2013 | Identical |
| BS EN ISO 13856-3:2013 | Identical |
| SN EN ISO 13856-3:2013 | Identical |
| NBN EN ISO 13856-3 : 2013 | Identical |
| PN EN ISO 13856-3 : 2013 | Identical |
| DIN EN ISO 13856-3 E : 2013 | Identical |
| NEN EN ISO 13856-3 : 2013 | Identical |
| UNI EN ISO 13856-3 : 2013 | Identical |
| NF EN ISO 13856-3 : 2013 | Identical |
| I.S. EN ISO 13856-3:2013 | Identical |
| BS EN 16564:2014 | Machines and plants for mining and tooling of natural stone. Safety. Requirements for bridge type sawing/milling machines, included numerical control (NC/CNC) versions |
| DIN EN 16564 E : 2015 | MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR BRIDGE TYPE SAWING/MILLING MACHINES, INCLUDED NUMERICAL CONTROL (NC/CNC) VERSIONS |
| UNI EN 16228-1 : 2014 | DRILLING AND FOUNDATION EQUIPMENT - SAFETY - PART 1: COMMON REQUIREMENTS |
| DIN EN 16564:2015-04 | Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing/milling machines, included numerical control (NC/CNC) versions |
| DIN EN 16500 E : 2014 | MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - VERTICAL BALING PRESSES - SAFETY REQUIREMENTS |
| I.S. EN 415-10:2014 | SAFETY OF PACKAGING MACHINES - PART 10: GENERAL REQUIREMENTS |
| I.S. EN 16564:2014 | MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR BRIDGE TYPE SAWING/MILLING MACHINES, INCLUDED NUMERICAL CONTROL (NC/CNC) VERSIONS |
| I.S. EN 16500:2014 | MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - VERTICAL BALING PRESSES - SAFETY REQUIREMENTS |
| I.S. EN 16228-1:2014 | DRILLING AND FOUNDATION EQUIPMENT - SAFETY - PART 1: COMMON REQUIREMENTS |
| UNE-EN 16500:2015 | Machines for compacting waste materials or recyclable fractions - Vertical baling presses - Safety requirements |
| EN 16228-1:2014 | Drilling and foundation equipment - Safety - Part 1: Common requirements |
| UNI EN 16500 : 2014 | MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - VERTICAL BALING PRESSES - SAFETY REQUIREMENTS |
| DIN EN 15571:2015-03 | Machines and plants for mining and tooling of natural stone - Safety - Requirements for surface finishing machines |
| DIN EN 415-10:2014-07 | SAFETY OF PACKAGING MACHINES - PART 10: GENERAL REQUIREMENTS |
| DIN EN 16474:2015-08 | PLASTICS AND RUBBER MACHINES - TYRE CURING PRESSES - SAFETY REQUIREMENTS |
| EN 16564:2014 | Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing/milling machines, included numerical control (NC/CNC) versions |
| EN 15571:2014 | Machines and plants for mining and tooling of natural stone - Safety - Requirements for surface finishing machines |
| I.S. EN 15571:2014 | MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR SURFACE FINISHING MACHINES |
| UNE-EN 16564:2015 | Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing/milling machines, included numerical control (NC/CNC) versions |
| DIN EN 16228-1:2014-10 | Drilling and foundation equipment - Safety - Part 1: Common requirements; German version EN 16228-1:2014 |
| UNE-EN 16474:2015 | Plastics and rubber machines - Tyre curing machines - Safety requirements |
| UNI EN 415-10 : 2014 | SAFETY OF PACKAGING MACHINES - PART 10: GENERAL REQUIREMENTS |
| PREN 12978 : DRAFT 2017 | INDUSTRIAL, COMMERCIAL AND GARAGE DOORS AND GATES - SAFETY DEVICES FOR POWER OPERATED DOORS AND GATES - REQUIREMENTS AND TEST METHODS |
| BS EN 15571:2014 | Machines and plants for mining and tooling of natural stone. Safety. Requirements for surface finishing machines |
| BS EN 16474:2015 | Plastics and rubber machines. Tyre curing machines. Safety requirements |
| BS EN 415-10:2014 | Safety of packaging machines General Requirements |
| DIN EN 15571 E : 2015 | MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR SURFACE FINISHING MACHINES |
| 14/30304361 DC : 0 | BS EN ISO 11111-1 - TEXTILE MACHINERY - SAFETY REQUIREMENTS - PART 1: COMMON REQUIREMENTS |
| DIN EN 16500:2014-10 | MACHINES FOR COMPACTING WASTE MATERIALS OR RECYCLABLE FRACTIONS - VERTICAL BALING PRESSES - SAFETY REQUIREMENTS |
| 17/30362673 DC : 0 | BS EN 12978 - INDUSTRIAL, COMMERCIAL AND GARAGE DOORS AND GATES - SAFETY DEVICES FOR POWER OPERATED DOORS AND GATES - REQUIREMENTS AND TEST METHODS |
| UNE-EN 16228-1:2015 | Drilling and foundation equipment - Safety - Part 1: Common requirements |
| EN 415-10:2014 | Safety of packaging machines - Part 10: General Requirements |
| EN 16500:2014 | Machines for compacting waste materials or recyclable fractions - Vertical baling presses - Safety requirements |
| EN 16474:2015 | Plastics and rubber machines - Tyre curing machines - Safety requirements |
| DIN EN 16474 E : 2015 | PLASTICS AND RUBBER MACHINES - TYRE CURING PRESSES - SAFETY REQUIREMENTS |
| 14/30304364 DC : 0 | BS EN ISO 11111-2:2005/AMD 2 - TEXTILE MACHINERY - SAFETY REQUIREMENTS - PART 2: SPINNING PREPARATORY AND SPINNING MACHINES |
| BS EN 16500:2014 | Machines for compacting waste materials or recyclable fractions. Vertical baling presses. Safety requirements |
| BS EN 16228-1:2014 | Drilling and foundation equipment. Safety Common requirements |
| UNE-EN 15571:2015 | Machines and plants for mining and tooling of natural stone - Safety - Requirements for surface finishing machines |
| I.S. EN 16474:2015 | PLASTICS AND RUBBER MACHINES - TYRE CURING MACHINES - SAFETY REQUIREMENTS |
| ISO 13855:2010 | Safety of machinery Positioning of safeguards with respect to the approach speeds of parts of the human body |
| ISO 14119:2013 | Safety of machinery Interlocking devices associated with guards Principles for design and selection |
| IEC 61000-4-4 : 3.0EN+(REDLINE+VERSION) | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| ISO 14120:2015 | Safety of machinery Guards General requirements for the design and construction of fixed and movable guards |
| IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| IEC 60947-5-1 : 4.0 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES |
| IEC 61000-4-4:2012 RLV | Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| IEC 61000-4-6 : 4.0 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS |
| IEC 61000-4-6:2013 | Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
| ISO 13856-2:2013 | Safety of machinery — Pressure-sensitive protective devices — Part 2: General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV | Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
| ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
| ISO 13856-1:2013 | Safety of machinery — Pressure-sensitive protective devices — Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| IEC 61439-1:2011 | Low-voltage switchgear and controlgear assemblies - Part 1: General rules |
| IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
| IEC 61032:1997 | Protection of persons and equipment by enclosures - Probes for verification |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| IEC 61000-6-2 : 3.0:2016 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 60947-5-5:1997+AMD1:2005+AMD2:2016 CSV | Low-voltage switchgear and controlgear - Part 5-5: Control circuitdevices and switching elements - Electrical emergency stop device with mechanical latching function |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.