• There are no items in your cart

EN ISO 15156-3:2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO 15156-3:2015)
Superseded date

03-29-2022

Published date

09-16-2015

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Factors affecting the cracking-resistance of CRAs
  and other alloys in H[2]S-containing environments
6 Qualification and selection of CRAs and other
  alloys with respect to SSC, SCC, and GHSC in
  H[2]S-containing environments
7 Purchasing information and marking
Annex A (normative) - Environmental cracking-resistant
        CRAs and other alloys (including Table A.1 - Guidance
        on the use of the materials selection tables)
Annex B (normative) - Qualification of CRAs for
        H[2]S-service by laboratory testing
Annex C (informative) - Information that should be
        supplied for material purchasing
Annex D (informative) - Materials chemical compositions
        and other information
Annex E (informative) - Nominated sets of test conditions
Bibliography

ISO 15156-3:2015 gives requirements and recommendations for the selection and qualification of CRAs (corrosion-resistant alloys) and other alloys for service in equipment used in oil and natural gas production and natural gas treatment plants in H2S-containing environments whose failure can pose a risk to the health and safety of the public and personnel or to the environment. It can be applied to help avoid costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials requirements of the appropriate design codes, standards, or regulations.ISO 15156-3:2015 addresses the resistance of these materials to damage that can be caused by sulfide stress-cracking (SSC), stress-corrosion cracking (SCC), and galvanically induced hydrogen stress cracking (GHSC).ISO 15156-3:2015 is concerned only with cracking. Loss of material by general (mass loss) or localized corrosion is not addressed.Table 1 provides a non-exhaustive list of equipment to which this part of ISO 15156 is applicable, including permitted exclusions.ISO 15156-3:2015 applies to the qualification and selection of materials for equipment designed and constructed using load controlled design methods. For design utilizing strain-based design methods, see ISO 15156‑1:2015, Clause 5.ISO 15156-3:2015 is not necessarily suitable for application to equipment used in refining or downstream processes and equipment.

Committee
CEN/TC 12
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

ISO 6507-1:2005 Metallic materials Vickers hardness test Part 1: Test method
ISO 13680:2010 Petroleum and natural gas industries Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock Technical delivery conditions
ISO 15510:2014 Stainless steels Chemical composition
ASTM E 562 : 2011 : REDLINE Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count
NACE TM 02 84 : 2016 EVALUATION OF PIPELINE AND PRESSURE VESSEL STEELS FOR RESISTANCE TO HYDROGEN-INDUCED CRACKING
ISO 6508-1:2016 Metallic materials — Rockwell hardness test — Part 1: Test method
ASTM A 744/A744M : 2013 : REDLINE Standard Specification for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service
ASTM E 384 : 2017 : REDLINE Standard Test Method for Microindentation Hardness of Materials
ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
NACE TM 01 77 : 2016 LABORATORY TESTING OF METALS FOR RESISTANCE TO SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING IN H[2]S ENVIRONMENTS
SAE AMS 2430 : 2015 SHOT PEENING
NACE TM 01 98 : 2016 SLOW STRAIN RATE TEST METHOD FOR SCREENING CORROSION-RESISTANT ALLOYS FOR STRESS CORROSION CRACKING IN SOUR OILFIELD SERVICE
ISO 15156-2:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons
ISO 7539-7:2005 Corrosion of metals and alloys Stress corrosion testing Part 7: Method for slow strain rate testing
ISO 15156-1:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 1: General principles for selection of cracking-resistant materials
ISO 10423:2009 Petroleum and natural gas industries Drilling and production equipment Wellhead and christmas tree equipment
NACE MR 01 76 : 2012 METALLIC MATERIALS FOR SUCKER-ROD PUMPS FOR CORROSIVE OILFIELD ENVIRONMENTS
ISO 11960:2014 Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.