EN ISO 2082:2017
Current
The latest, up-to-date edition.
08-30-2017
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, abbreviated terms and symbols
4 Information to be supplied by the purchaser to the
electroplater
5 Designation
6 Requirements
Annex A (normative) - Designation of supplementary
treatments
Annex B (normative) - Measurement of average thickness
of coating on small articles
Annex C (informative) - Additional information on corrosion
resistance, rinsing and drying, processing parts in bulk
and dyeing of chromate conversion coatings
Bibliography
ISO 2082:2017 specifies the requirements of electroplated coatings of cadmium with supplementary treatments on iron and steel. It includes information that is to be supplied by the purchaser to the electroplater, and describes coating requirements, including those for heat treatment before and after electroplating.It is not applicable to coatings applied- to sheet, strip or wire in the non-fabricated form,- to close-coiled springs, or- for purposes other than protective, intrinsic lubricity, ductility, electrical conductivity and low contact resistance use.ISO 2082:2017 does not specify requirements for the surface condition of the basis metal prior to electrodeposition with cadmium.The coating thickness that can be applied to threaded components can be limited by dimensional requirements, including class or fit.Additional information on corrosion resistance, rinsing and drying, processing parts in bulk and dyeing of chromate conversion coatings is given in Annex C.
| Committee |
CEN/TC 262
|
| DevelopmentNote |
Supersedes EN 12330. (02/2009)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| BS EN ISO 2082:2017 | Identical |
| SN EN ISO 2082 : 2017 | Identical |
| UNE-EN ISO 2082:2010 | Identical |
| NS EN ISO 2082 : 2017 | Identical |
| UNE-EN ISO 2082:2017 | Identical |
| NEN EN ISO 2082 : 2017 | Identical |
| DIN EN ISO 2082:2016-04 (Draft) | Identical |
| DIN EN ISO 2082:2017-12 | Identical |
| PN EN ISO 2082 : 2017 | Identical |
| NF EN ISO 2082 : 2017 | Identical |
| I.S. EN ISO 2082:2017 | Identical |
| UNI EN ISO 2082 : 2009 | Identical |
| NBN EN ISO 2082 : 2009 | Identical |
| ISO 2082:2017 | Identical |
| DIN EN ISO 2082:2009-06 | Identical |
| UNI EN ISO 2082 : 2017 | Identical |
| BS EN 2535:2011 | Aerospace series. Vacuum deposition of cadmium |
| PREN 2133 : 200P1 | AEROSPACE SERIES - CADMIUM PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER, COPPER ALLOYS AND NICKEL ALLOYS |
| I.S. EN 2535:2011 | AEROSPACE SERIES - VACUUM DEPOSITION OF CADMIUM |
| DIN EN 15330-2:2015-09 (Draft) | SURFACES FOR SPORTS AREAS - SYNTHETIC TURF AND NEEDLE-PUNCHED SURFACES PRIMARILY DESIGNED FOR OUTDOOR USE - PART 2: SPECIFICATION FOR NEEDLE-PUNCHED SURFACES FOR TENNIS AND MULTI-SPORT SURFACES |
| EN 2133:2010 | Aerospace series - Cadmium plating of steels with specified tensile strength ≤ 1 450 MPa, copper, copper alloys and nickel alloys |
| 15/30326242 DC : 0 | BS EN 15330-2 - SURFACES FOR SPORTS AREAS - SYNTHETIC TURF AND NEEDLE-PUNCHED SURFACES PRIMARILY DESIGNED FOR OUTDOOR USE - PART 2: SPECIFICATION FOR NEEDLE-PUNCHED SURFACES FOR TENNIS AND MULTISPORT SURFACES |
| I.S. EN 15330-2:2017 | SURFACES FOR SPORTS AREAS - SYNTHETIC TURF AND NEEDLE-PUNCHED SURFACES PRIMARILY DESIGNED FOR OUTDOOR USE - PART 2: SPECIFICATION FOR NEEDLE-PUNCHED SURFACES FOR TENNIS AND MULTI-SPORT SURFACES |
| I.S. EN 2133:2010 | AEROSPACE SERIES - CADMIUM PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER, COPPER ALLOYS AND NICKEL ALLOYS |
| UNI EN 2133 : 2011 | AEROSPACE SERIES - CADMIUM PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER, COPPER ALLOYS AND NICKEL ALLOYS |
| PREN 15330-2 : DRAFT 2015 | SURFACES FOR SPORTS AREAS - SYNTHETIC TURF AND NEEDLE-PUNCHED SURFACES PRIMARILY DESIGNED FOR OUTDOOR USE - PART 2: SPECIFICATION FOR NEEDLE-PUNCHED SURFACES FOR TENNIS AND MULTISPORT SURFACES |
| 16/30339916 DC : 0 | BS EN 2133 - AEROSPACE SERIES - CADMIUM PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER, COPPER ALLOYS AND NICKEL ALLOYS |
| 17/30366369 DC : 0 | BS EN 2133 AEROSPACE SERIES - CADMIUM PLATING OF STEELS WITH SPECIFIED TENSILE STRENGTH <= 1450 MPA, COPPER, COPPER ALLOYS AND NICKEL ALLOYS |
| BS EN 2133:2010 | Aerospace series. Cadmium plating of steels with specified tensile strength ≤ 1450 MPa, copper, copper alloys and nickel alloys |
| EN 15330-2:2017 | Surfaces for sports areas - Synthetic turf and needle-punched surfaces primarily designed for outdoor use - Part 2: Specification for needle-punched surfaces for tennis and multi-sport surfaces |
| EN 2535:2011 | Aerospace series - Vacuum deposition of cadmium |
| UNI EN 2535 : 2012 | AEROSPACE SERIES - VACUUM DEPOSITION OF CADMIUM |
| NF EN 2535 : 2012 | AEROSPACE SERIES - VACUUM DEPOSITION OF CADMIUM |
| BS EN 15330-2:2017 | Surfaces for sports areas. Synthetic turf and needle-punched surfaces primarily designed for outdoor use Specification for needle-punched surfaces for tennis and multi-sport surfaces |
| DIN EN 15330-2:2017-09 | SURFACES FOR SPORTS AREAS - SYNTHETIC TURF AND NEEDLE-PUNCHED SURFACES PRIMARILY DESIGNED FOR OUTDOOR USE - PART 2: SPECIFICATION FOR NEEDLE-PUNCHED SURFACES FOR TENNIS AND MULTI-SPORT SURFACES |
| ISO 2080:2008 | Metallic and other inorganic coatings Surface treatment, metallic and other inorganic coatings Vocabulary |
| ISO 9587:2007 | Metallic and other inorganic coatings Pretreatment of iron or steel to reduce the risk of hydrogen embrittlement |
| ISO 27830:2008 | Metallic and other inorganic coatings Guidelines for specifying metallic and inorganic coatings |
| ISO 3543:2000 | Metallic and non-metallic coatings Measurement of thickness Beta backscatter method |
| ISO 27831-1:2008 | Metallic and other inorganic coatings — Cleaning and preparation of metal surfaces — Part 1: Ferrous metals and alloys |
| ISO 1463:2003 | Metallic and oxide coatings Measurement of coating thickness Microscopical method |
| ISO 10587:2000 | Metallic and other inorganic coatings Test for residual embrittlement in both metallic-coated and uncoated externally-threaded articles and rods Inclined wedge method |
| ISO 15724:2001 | Metallic and other inorganic coatings — Electrochemical measurement of diffusible hydrogen in steels — Barnacle electrode method |
| ISO 3892:2000 | Conversion coatings on metallic materials Determination of coating mass per unit area Gravimetric methods |
| ISO 4518:1980 | Metallic coatings Measurement of coating thickness Profilometric method |
| ISO 2819:1980 | Metallic coatings on metallic substrates — Electrodeposited and chemically deposited coatings — Review of methods available for testing adhesion |
| ISO 27831-2:2008 | Metallic and other inorganic coatings — Cleaning and preparation of metal surfaces — Part 2: Non-ferrous metals and alloys |
| ASTM E 527 : 2016 : REDLINE | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ISO 4519:1980 | Electrodeposited metallic coatings and related finishes — Sampling procedures for inspection by attributes |
| ISO 3497:2000 | Metallic coatings Measurement of coating thickness X-ray spectrometric methods |
| ISO 9588:2007 | Metallic and other inorganic coatings Post-coating treatments of iron or steel to reduce the risk of hydrogen embrittlement |
| ISO 2178:2016 | Non-magnetic coatings on magnetic substrates Measurement of coating thickness Magnetic method |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 2177:2003 | Metallic coatings — Measurement of coating thickness — Coulometric method by anodic dissolution |
| ISO 10289:1999 | Methods for corrosion testing of metallic and other inorganic coatings on metallic substrates Rating of test specimens and manufactured articles subjected to corrosion tests |
| ISO 3613:2010 | Metallic and other inorganic coatings Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys Test methods |
| ISO 2064:1996 | Metallic and other inorganic coatings — Definitions and conventions concerning the measurement of thickness |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.