|
ISO/IEC 17025:2005
|
General requirements for the competence of testing and calibration laboratories
|
|
ISO 4427:1996
|
Polyethylene (PE) pipes for water supply Specifications
|
|
NSF 61 : 2016
|
DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS
|
|
ASTM D 618 : 2013 : REDLINE
|
Standard Practice for Conditioning Plastics for Testing
|
|
ASTM D 2774 : 2012 : REDLINE
|
Standard Practice for Underground Installation of Thermoplastic Pressure Piping
|
|
ASTM D 2839 : 2016 : REDLINE
|
Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
|
|
ASTM D 1238 : 2013 : REDLINE
|
Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
|
|
AWWA C906:2015
|
POLYETHYLENE (PE) PRESSURE PIPE AND FITTINGS, 4 IN. THROUGH 65 IN. (100 MM THROUGH 1,650 MM), FOR WATERWORKS
|
|
ISO 161-1:1996
|
Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series
|
|
PPI TR 3 : 2017
|
POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
|
|
IEEE/ASTM SI_10-2010
|
American National Standard for Metric Practice
|
|
ASTM D 2683 : 2014 : REDLINE
|
Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
|
|
ASTM D 1603 : 2014 : REDLINE
|
Standard Test Method for Carbon Black Content in Olefin Plastics
|
|
ASTM F 714 : 2013 : REDLINE
|
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
|
|
AWWA C901 : 2017
|
POLYETHYLENE (PE) PRESSURE PIPE AND TUBING, 3/4 IN. (19 MM) THROUGH 3 IN. (76 MM), FOR WATER SERVICE
|
|
ASTM D 2444 : 1999
|
Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
|
|
AWWA M55 : 1
|
PE PIPE - DESIGN AND INSTALLATION
|
|
ASTM D 2122 : 2016 : REDLINE
|
Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
|
|
ASTM F 1055 : 2016-09
|
SPECIFICATION FOR ELECTROFUSION TYPE POLYETHYLENE FITTINGS FOR OUTSIDE DIAMETER CONTROLLED POLYETHYLENE AND CROSSLINKED POLYETHYLENE (PEX) PIPE AND TUBING
|
|
ASTM D 2290 : 2016-12
|
TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE
|
|
ASTM D 3350 : 2014 : REDLINE
|
Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
|
|
ASTM D 3035 : 2015 : REDLINE
|
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
|
|
ASTM D 638 : 2014 : REDLINE
|
Standard Test Method for Tensile Properties of Plastics
|
