• I.S. EN 16228-6:2014

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    DRILLING AND FOUNDATION EQUIPMENT - SAFETY - PART 6: JETTING, GROUTING AND INJECTION EQUIPMENT

    Available format(s):  Hardcopy, PDF

    Superseded date:  01-28-2022

    Language(s):  English

    Published date:  01-01-2014

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 List of additional significant hazards
    5 Safety requirements and/or protective measures
    6 Verification of the safety requirements and/or
      protective measures
    7 Information for use
    Annex A (normative) - Noise test code
    Annex ZA (informative) - Relationship between this
             European Standard and the Essential
             Requirements of EU Directive 2006/42/EC
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes all significant hazards for jetting, grouting and injection equipment when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer associated with the whole life time of the machine.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 791 & I.S. EN 996. (06/2014)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 12001:2012 Conveying, spraying and placing machines for concrete and mortar - Safety requirements
    ISO 4413:2010 Hydraulic fluid power General rules and safety requirements for systems and their components
    ISO 12100:2010 Safety of machinery General principles for design Risk assessment and risk reduction
    EN 16228-2:2014 Drilling and foundation equipment - Safety - Part 2: Mobile drill rigs for civil and geotechnical engineering, quarrying and mining
    EN 12151:2007 MACHINERY AND PLANTS FOR THE PREPARATION OF CONCRETE AND MORTAR - SAFETY REQUIREMENTS
    EN 16228-1:2014 Drilling and foundation equipment - Safety - Part 1: Common requirements
    PREN 854 : DRAFT 2011 RUBBER HOSES AND HOSE ASSEMBLIES - TEXTILE REINFORCED HYDRAULIC TYPE - SPECIFICATION
    EN 809 : 1998 COR 2010 PUMPS AND PUMP UNITS FOR LIQUIDS - COMMON SAFETY REQUIREMENTS
    EN ISO 4414 : 2010 PNEUMATIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS (ISO 4414:2010)
    PREN 857 : DRAFT 2011 RUBBER HOSES AND HOSE ASSEMBLIES - WIRE BRAID REINFORCED COMPACT TYPE FOR HYDRAULIC APPLICATIONS - SPECIFICATION
    EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
    EN 16228-4:2014 Drilling and foundation equipment - Safety - Part 4: Foundation equipment
    ISO 4414:2010 Pneumatic fluid power General rules and safety requirements for systems and their components
    PREN 856 : DRAFT 2011 RUBBER HOSES AND HOSE ASSEMBLIES - RUBBER-COVERED SPIRAL WIRE REINFORCED HYDRAULIC TYPE - SPECIFICATION
    EN ISO 4413 : 2010 HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS
    PREN 853 : DRAFT 2011 RUBBER HOSES AND HOSE ASSEMBLIES - WIRE BRAID REINFORCED HYDRAULIC TYPE - SPECIFICATION
    PREN 855 : DRAFT 2011 PLASTICS HOSES AND HOSE ASSEMBLIES - THERMOPLASTICS TEXTILE REINFORCED HYDRAULIC TYPE - SPECIFICATION
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective