• There are no items in your cart

I.S. EN 55016-1-1:2010

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-1: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - MEASURING APPARATUS
Available format(s)

Hardcopy , PDF

Superseded date

08-03-2019

Language(s)

English

Published date

01-01-2010

Preview

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Quasi-peak measuring receivers for the frequency range
  9 kHz to 1000 MHz
5 Measuring receivers with peak detector for the frequency
  range 9 kHz to 18 GHz
6 Measuring receivers with average detector for the frequency
  range 9 kHz to 18 GHz
7 Measuring receivers with rms detector for the frequency range
  9 kHz to 18 GHz
8 Measuring receivers for the frequency range 1 GHz to 18 GHz
  with amplitude probability distribution (APD) measuring function
9 Disturbance analyzers
Annex A (normative) - Determination of response to repeated pulses
        of quasi-peak and rms-average measuring receivers
Annex B (normative) - Determination of pulse generator spectrum
Annex C (normative) - Accurate measurements of the output of
        nanosecond pulse generators
Annex D (normative) - Influence of the quasi-peak measuring
        receiver characteristics on its pulse response
Annex E (normative) - Response of average and peak measuring
        receivers
Annex F (normative) - Performance check of the exceptions from
        the definitions of a click according to 4.2.3 of CISPR
        14-1
Annex G (informative) - Rationale for the specifications of the
        APD measuring function
Annex H (informative) - Characteristics of a quasi-peak measuring
        receiver
Annex I (informative) - Example of EMI receiver and swept spectrum
        analyzer architecture
Annex J (normative) - Requirements when using
        an external preamplifier with a measuring receiver
Bibliography
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

Describes the characteristics and performance of equipment for the measurement of radio disturbance in the frequency range 9 kHz to 18 GHz.

DocumentType
Standard
Pages
220
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

CISPR 14-1:2016 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission
CISPR 16-4-2:2011+AMD1:2014 CSV Specification for radio disturbance and immunity measuring apparatusand methods - Part 4-2: Uncertainties, statistics and limit modelling - Measurement instrumentation uncertainty
EN 55016-2-3:2017 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements
EN 55016-2-2:2011 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-2: Methods of measurement of disturbances and immunity - Measurement of disturbance power
CISPR 16-2-2:2010 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-2: Methods of measurement of disturbances and immunity - Measurement of disturbance power
CISPR 16-1-4:2010+AMD1:2012+AMD2:2017 CSV Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements
CISPR 16-1-3:2004+AMD1:2016 CSV Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-3: Radio disturbance and immunity measuring apparatus - Ancillary equipment - Disturbance power
CISPR 16-2-1:2014 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-1: Methods of measurement of disturbances and immunity - Conducted disturbance measurements
CISPR 15:2013+AMD1:2015 CSV Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment
CISPR 16-1-5:2014+AMD1:2016 CSV Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-5: Radio disturbance and immunity measuring apparatus - Antenna calibration sites and reference test sites for 5 MHz to 18 GHz
CISPR TR 16-4-3:2004+AMD1:2006 CSV Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-3: Uncertainties, statistics and limit modelling - Statistical considerations in the determination of EMC compliance of mass-produced products
CISPR 32:2015 RLV Electromagnetic compatibility of multimedia equipment - Emission requirements
CISPR 16-2-4:2003 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-4: Methods of measurement of disturbances and immunity - Immunity measurements
CISPR 22:2008 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement
CISPR TR 16-4-1:2009 Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-1: Uncertainties, statistics and limit modelling - Uncertainties in standardized EMC tests
CISPR 25:2016 Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers
CISPR 16-2-3:2016 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements
CISPR TR 16-4-4:2007 Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-4: Uncertainties, statistics and limit modelling - Statistics of complaints and a model for the calculation of limits for the protection of radio services
CISPR 11:2015 RLV Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
EN 50065-1:2011 Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 1: General requirements, frequency bands and electromagnetic disturbances
EN 55016-2-1:2014/A1:2017 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 2-1: METHODS OF MEASUREMENT OF DISTURBANCES AND IMMUNITY - CONDUCTED DISTURBANCE MEASUREMENTS (CISPR 16-2-1:2014/A1:2017)
EN 55014-1:2017 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission
CISPR TR 16-3:2010+AMD1:2012+AMD2:2015 CSV Specification for radio disturbance and immunity measuring apparatus and methods - Part 3: CISPR technical reports

View more information
US$131.55
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.