• There are no items in your cart

I.S. EN 55016-2-1:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 2-1: METHODS OF MEASUREMENT OF DISTURBANCES AND IMMUNITY - CONDUCTED DISTURBANCE MEASUREMENTS
Available format(s)

Hardcopy , PDF

Superseded date

10-27-2020

Language(s)

English

Published date

01-01-2014

Preview

National Foreword
FOREWORD
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 Types of disturbance to be measured
5 Connection of measuring equipment
6 General measurement requirements and conditions
7 Measurement of disturbances conducted along leads,
  9 kHz to 30 MHz
8 Automated measurement of disturbances
9 Test set-up and measurement procedure using the
  CDNE in the frequency range 30 MHz to 300 MHz
Annex A (informative) - Guidelines to connection of
        electrical equipment to the artificial mains
        network
Annex B (informative) - Use of spectrum analyzers and
        scanning receivers
Annex C (informative) - Decision tree for use of detectors
        for conducted measurements
Annex D (informative) - Scan rates and measurement times
        for use with the average detector
Annex E (informative) - Guidelines for the improvement of
        the test setup with AN[s]
Annex F (normative) - Determination of suitability of spectrum
        analyzers for compliance tests
Annex G (informative) - Basic Guidance for measurements on
        telecommunications ports
Annex H (normative) - Specifics for conducted disturbance
        on telecommunication ports
Annex I (informative) - Examples of AAN[s] and AN[s] for screened
        cables
Bibliography
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

Describes the methods of measurement of disturbance phenomena in general in the frequency range 9 kHz to 18 GHz and especially of conducted disturbance phenomena in the frequency range 9 kHz to 30 MHz.

DevelopmentNote
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (11/2017)
DocumentType
Standard
Pages
270
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

CISPR 14-1:2016 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission
CISPR 16-4-2:2011+AMD1:2014 CSV Specification for radio disturbance and immunity measuring apparatusand methods - Part 4-2: Uncertainties, statistics and limit modelling - Measurement instrumentation uncertainty
CISPR 16-1-4:2010+AMD1:2012+AMD2:2017 CSV Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements
CISPR 16-1-1:2015 Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus
IEC TR 60083:2015 Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC
CISPR TR 16-4-3:2004+AMD1:2006 CSV Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-3: Uncertainties, statistics and limit modelling - Statistical considerations in the determination of EMC compliance of mass-produced products
IEC 61000-4-6 : 4.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS
IEC 61000-4-6:2013 Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields
CISPR TR 16-4-1:2009 Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-1: Uncertainties, statistics and limit modelling - Uncertainties in standardized EMC tests
ISO/IEC Guide 99:2007 International vocabulary of metrology Basic and general concepts and associated terms (VIM)
CISPR 16-2-3:2016 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements
CISPR 11:2015 RLV Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
IEC 61010-1:2010+AMD1:2016 CSV Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements
EN 55014-1:2017 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission
EN 55016-1-1:2010/A2:2014 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-1: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - MEASURING APPARATUS (CISPR 16-1-1:2010/A2:2014)
CISPR TR 16-3:2010+AMD1:2012+AMD2:2015 CSV Specification for radio disturbance and immunity measuring apparatus and methods - Part 3: CISPR technical reports

View more information
US$152.38
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.