• There are no items in your cart

I.S. EN 60950-22:2017

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 22: EQUIPMENT TO BE INSTALLED OUTDOORS
Available format(s)

Hardcopy , PDF

Withdrawn date

01-06-2023

Language(s)

English

Published date

01-01-2017

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

National Forword
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Conditions for outdoor equipment
5 Marking and instructions
6 Protection from electrical shock in an outdoor
   location
7 Wiring terminals for connection of external
   conductors
8 Construction requirements for outdoor enclosures
9 Protection of equipment within an outdoor
   enclosure
10 Mechanical strength of enclosures
11 Outdoor equipment containing valve regulated
  or vented batteries
Annex A (normative) - Water-saturated sulphur
        dioxide atmosphere
Annex B (normative) - Water spray test
Annex C (normative) - Ultraviolet light conditioning
        test
Annex D (normative) - Gasket tests
Annex E (informative) - Rationale
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Pertains to information technology equipment intended to be installed in an OUTDOOR LOCATION.

DevelopmentNote
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
DocumentType
Standard
Pages
78
PublisherName
National Standards Authority of Ireland
Status
Withdrawn
Supersedes

IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
ISO 4892-1:2016 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
IEC 60364-4-43:2008 Low-voltage electrical installations - Part 4-43: Protection for safety - Protection against overcurrent
EN ISO 8256:2004 Plastics - Determination of tensile-impact strength (ISO 8256:2004)
EN 62368-1:2014/AC:2017-03 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED)
EN ISO 180:2000/A2:2013 PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013)
EN ISO 4892-1:2016 Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016)
EN ISO 3231:1997 Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993)
IEC 61587-1:2016 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
IEC 60896-21:2004 Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test
IEC 60364-5-53:2001+AMD1:2002+AMD2:2015 CSV Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control
EN 60950-1:2006/A2:2013 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED)
IEC 60068-2-11:1981 Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist
EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
ISO 8256:2004 Plastics — Determination of tensile-impact strength
ISO 14993:2001 Corrosion of metals and alloys Accelerated testing involving cyclic exposure to salt mist, "dry" and "wet" conditions
IEC 62305-1:2010 Protection against lightning - Part 1: General principles
ISO 4628-3:2016 Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rusting
ISO 21207:2015 Corrosion tests in artificial atmospheres — Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying
ISO 180:2000 Plastics Determination of Izod impact strength
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
IEC 60896-22:2004 Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements
ISO/TS 18173:2005 Non-destructive testing General terms and definitions
IEC 61643-11:2011 Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods
IEC 61969-3:2011 Mechanical structures for electronic equipment - Outdoor enclosures - Part 3: Environmental requirements, tests and safety aspects
ISO 4892-4:2013 Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps
IEC 61439-5:2014 Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks
ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
EN 60068-2-11:1999 Environmental testing - Part 2: Tests - Test Ka: Salt mist
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 178:2010 Plastics Determination of flexural properties
ASTM D 471 : 2016-02 TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN ISO 4892-2:2013 Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
IEC 62368-1:2014 Audio/video, information and communication technology equipment - Part 1: Safety requirements
IEC 62485-2:2010 Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries
ISO 3231:1993 Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide

View more information
US$46.04
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.