Preview

LAMP CONTROLGEAR - PART 2-1: PARTICULAR REQUIREMENTS FOR STARTING DEVICES (OTHER THAN GLOW STARTERS)

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2004

Publisher

National Standards Authority of Ireland

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions
4 General requirements
5 General notes on tests
6 Classification
7 Marking
8 Protection against accidental contact with live parts
9 Terminals
10 Provisions for earthing
11 Moisture resistance and insulation
12 Electric strength
13 Thermal endurance test for windings
14 Fault conditions
15 Heating of built-in and independent starting devices
16 Pulse voltage of ignitors
17 Mechanical strength
18 Construction
19 Creepage distances and clearances
20 Screws, current-carrying parts and connections
21 Resistance to heat, fire and tracking
22 Resistance to corrosion
Annex A (normative) - Test to establish whether a conductive
        part is a live part which may cause an electric shock
Annex B (normative) - Particular requirements for thermally
        protected lamp controlgear
Annex C (normative) - Particular requirements for electronic
        lamp controlgear with means of protection against
        overheating
Annex D (normative) - Requirements for carrying out the
        heating tests of thermally protected lamp
        controlgear
Annex E (normative) - Use of constant S other than 4500 in t[w]
        tests
Annex F (normative) - Draught-proof enclosure
Annex G (informative) - Explanation of the derivation of the
        values of pulse voltages
Annex H (normative) - Tests
Annex I (normative) - Mechanical strength testing
Annex J (normative) - Precautions to be observed when measuring
        with sphere-gaps
Bibliography
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

Describes particular safety requirements for starting devices (starters other than glow starters and ignitors) for fluorescent and other discharge lamps.

DevelopmentNote	Together with I.S. EN 61347-1 and parts 2-2, 2-3, 2-4, 2-5, 2-6, 2-7, 2-8 and 2-9 of I.S. EN 61347 supersedes I.S. EN 60920, I.S. EN 60922, I.S. EN 60924, I.S. EN 60926, I.S. EN 60928 and I.S. EN 61046. (07/2005) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
DocumentType	Standard
Pages	78
PublisherName	National Standards Authority of Ireland
Status	Current
Supersedes	I.S. EN 61046:1995 I.S. EN 60924:1992 I.S. EN 60928:1997 I.S. EN 60926:1999 I.S. EN 60922:1998 I.S. EN 60920:1992

Standards	Relationship
BS EN 61347-2-1 : 2001	Identical
SN EN 61347-2-1 : 2001 AMD 1 2006	Identical
EN 61347-2-1:2001/A2:2014	Identical
NF EN 61347-2-1 : 2001 AMD 2 2014	Identical
DIN EN 61347-2-1 : 2014	Identical
UNE-EN 61347-2-1:2002	Identical

IEC 60112:2003+AMD1:2009 CSV	Method for the determination of the proof and the comparative tracking indices of solid insulating materials
EN 60052:2002	Voltage measurement by means of standard air gaps
EN 60188:2001	High-pressure mercury vapour lamps - Performance specifications
EN 60192:2001	Low pressure sodium vapour lamps - Performance specifications
EN 60068-2-75:2014	Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
IEC 60730-2-3:2006	Automatic electrical controls for household and similar use - Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps
IEC 60662:2011	High-pressure sodium vapour lamps - Performance specifications
IEC 60192:2001	Low-pressure sodium vapour lamps - Performance specifications
IEC 60188:2001	High-pressure mercury vapour lamps - Performance specifications
IEC 61347-2-9:2012	Lamp controlgear - Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps)
EN 61199:2011/A2:2015	SINGLE-CAPPED FLUORESCENT LAMPS - SAFETY SPECIFICATIONS (IEC 61199:2011/A2:2014)
IEC 61347-1:2015 RLV	Lamp controlgear - Part 1: General and safety requirements
IEC 60929:2011+AMD1:2015 CSV	AC and/or DC-supplied electronic control gear for tubularfluorescent lamps - Performance requirements
IEC 60695-2-1-0 : 1.0	FIRE HAZARD TESTING - TEST METHODS - GLOW-WIRE TEST METHODS - GENERAL
EN 60255-8:1998	Electrical relays - Part 8: Thermal electrical relays
IEC 61199:2011+AMD1:2012+AMD2:2014 CSV	Single-capped fluorescent lamps - Safety specifications
IEC 61167:2015	Metal halide lamps - Performance specification
IEC 60410:1973	Sampling plans and procedures for inspection by attributes
IEC 60921:2004+AMD1:2006 CSV	Ballasts for tubular fluorescent lamps - Performance requirements
IEC 60901:1996+AMD1:1997+AMD2:2000 CSV	Single-capped fluorescent lamps - Performance specifications
IEC 60317-0-1:2013	Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
EN 61347-1:2015	Lamp controlgear - Part 1: General and safety requirements
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV	Degrees of protection provided by enclosures (IP Code)
IEC 60691:2015	Thermal-links - Requirements and application guide
IEC 60598-1:2014+AMD1:2017 CSV	Luminaires - Part 1: General requirements and tests
ISO 4046:1978	Paper, board, pulp and related terms — Vocabulary
IEC 61347-2-2:2011	Lamp controlgear - Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps
IEC 60927:2007+AMD1:2013 CSV	Auxiliaries for lamps - Starting devices (other than glow starters)- Performance requirements
IEC 60255-8:1990	Electrical relays - Part 8: Thermal electrical relays
IEC 60052:2002	Voltage measurement by means of standard air gaps
EN 60155:1995/A2:2007	GLOW-STARTERS FOR FLUORESCENT LAMPS
IEC 60068-2-75:2014	Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
EN 60662:2012	High-pressure sodium vapour lamps - Performance specifications
IEC 60155:1993	Glow-starters for fluorescent lamps
IEC 60923:2005+AMD1:2006 CSV	Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluorescent lamps) - Performance requirements
ISO 3864:1984	Safety colours and safety signs
IEC 61347-2-8:2000+AMD1:2006 CSV	Lamp controlgear - Part 2-8: Particular requirements for ballasts for fluorescent lamps
EN 61195:1999/A2:2015	DOUBLE-CAPPED FLUORESCENT LAMPS - SAFETY SPECIFICATIONS (IEC 61195:1999/A2:2014)
IEC 60990:2016	Methods of measurement of touch current and protective conductor current
IEC 61195:1999+AMD1:2012+AMD2:2014 CSV	Double-capped fluorescent lamps - Safety specifications

View more information

US$46.04

Excluding Tax where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

I.S. EN 61347-2-1:2004

LAMP CONTROLGEAR - PART 2-1: PARTICULAR REQUIREMENTS FOR STARTING DEVICES (OTHER THAN GLOW STARTERS)

Table of Contents

Abstract

General Product Information

International Equivalents

Standards Referencing This Book

Category

Subcategory