• There are no items in your cart

I.S. EN 62282-3-201:2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

FUEL CELL TECHNOLOGIES - PART 3-201: STATIONARY FUEL CELL POWER SYSTEMS - PERFORMANCE TEST METHODS FOR SMALL FUEL CELL POWER SYSTEMS
Available format(s)

Hardcopy , PDF

Superseded date

04-13-2022

Language(s)

English

Published date

01-01-2017

Preview

National Foreword
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Configuration of small stationary fuel cell power system
6 Reference conditions
7 Heating value base
8 Test preparation
9 Test set-up
10 Instruments and measurement methods
11 Test conditions
12 Operating process
13 Test plan
14 Type tests on electric/thermal performance
15 Type tests on environmental performance
16 Test reports
Annex A (normative) - Heating values for components of
        natural gases
Annex B (informative) - Examples of composition for natural
        gases and propane gases
Annex C (informative) - Example of a test operation
        schedule
Annex D (informative) - Typical exhaust gas components
Annex E (informative) - Guidelines for the contents of
        detailed and full reports
Annex F (informative) - Selected duration of rated power
        operation
Bibliography
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

Describes test methods for the electrical, thermal and Environmental performance of small stationary fuel cell power systems that meet the following criteria: - output - rated electric power output of less than 10 kW; - output mode - grid-connected/independent operation or stand-alone operation with singlephase AC output or 3-phase AC output not exceeding 1000 V, or DC output not exceeding1500 V; - operating pressure - maximum allowable working pressure of less than 0,1 MPa (gauge) for the fuel and oxidant passages; - fuel - gaseous fuel (natural gas, liquefied petroleum gas, propane, butane, hydrogen, etc.) or liquid fuel (kerosene, methanol, etc.); - oxidant - air.

DevelopmentNote
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
DocumentType
Standard
Pages
170
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

Standards Relationship
EN 62282-3-201:2017 Identical

ISO/TR 15916:2015 Basic considerations for the safety of hydrogen systems
IEC 61000-4-8 : 2.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-8: TESTING AND MEASUREMENT TECHNIQUES - POWER FREQUENCY MAGNETIC FIELD IMMUNITY TEST
IEC 61672-2:2013+AMD1:2017 CSV Electroacoustics - Sound level meters - Part 2: Pattern evaluation tests
ISO 6976:2016 Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition
IEC 61000-4-4 : 3.0EN+(REDLINE+VERSION) ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST
EN 61000-4-11:2004/A1:2017 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-11: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE DIPS, SHORT INTERRUPTIONS AND VOLTAGE VARIATIONS IMMUNITY TESTS (IEC 61000-4-11:2004/A1:2017)
IEC 60050-601:1985 International Electrotechnical Vocabulary (IEV) - Part 601: Generation, transmission and distribution of electricity - General
IEC TS 62282-1:2013 Fuel cell technologies - Part 1: Terminology
IEC 61000-4-11:2004+AMD1:2017 CSV Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests
ISO 7941:1988 Commercial propane and butane Analysis by gas chromatography
ISO 7935:1992 Stationary source emissions — Determination of the mass concentration of sulfur dioxide — Performance characteristics of automated measuring methods
ASTM F 2602 : 2013-10 TEST METHOD FOR DETERMINING THE MOLAR MASS OF CHITOSAN AND CHITOSAN SALTS BY SIZE EXCLUSION CHROMATOGRAPHY WITH MULTI-ANGLE LIGHT SCATTERING DETECTION (SEC-MALS)
SAE ARP 1533 : 2016 PROCEDURE FOR THE ANALYSIS AND EVALUATION OF GASEOUS EMISSIONS FROM AIRCRAFT ENGINES
ISO 6060:1989 Water quality — Determination of the chemical oxygen demand
IEC 61000-4-6 : 4.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS
IEC 62282-3-200:2015 Fuel cell technologies - Part 3-200: Stationary fuel cell power systems - Performance test methods
ISO 11042-1:1996 Gas turbines — Exhaust gas emission — Part 1: Measurement and evaluation
ISO 11042-2:1996 Gas turbines — Exhaust gas emission — Part 2: Automated emission monitoring
EN 61000-6-2:2005/corrigendum:2005 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005)
EN 61000-4-8:2010 Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test
IEC 61000-4-2:2008 Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test
IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test
EN 61000-3-2:2014 Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current ≤ 16 A per phase)
ISO 11541:1997 Natural gas Determination of water content at high pressure
EN 62282-3-200:2016 Fuel cell technologies - Part 3-200: Stationary fuel cell power systems - Performance test methods
ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
EN 61000-4-4:2012 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012)
ISO 5815-2:2003 Water quality — Determination of biochemical oxygen demand after n days (BODn) — Part 2: Method for undiluted samples
CISPR 11:2015 RLV Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
ISO 10849:1996 Stationary source emissions — Determination of the mass concentration of nitrogen oxides — Performance characteristics of automated measuring systems
EN 61000-4-6:2014/AC:2015 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS (IEC 61000-4-6:2013)
ISO 10523:2008 Water quality — Determination of pH
ISO 10396:2007 Stationary source emissions — Sampling for the automated determination of gas emission concentrations for permanently-installed monitoring systems
ISO 6798:1995 Reciprocating internal combustion engines Measurement of emitted airborne noise Engineering method and survey method
IEC 61000-6-2 : 3.0:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
IEC 61000-3-2 : 4.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE)

View more information
US$108.53
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.