• I.S. EN ISO 10407-2:2008

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    PETROLEUM AND NATURAL GAS INDUSTRIES - ROTARY DRILLING EQUIPMENT - PART 2: INSPECTION AND CLASSIFICATION OF USED DRILL STEM ELEMENTS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2008

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
       4.1 Symbols
       4.2 Abbreviated terms
    5 Conformance
       5.1 Basis for inspection
       5.2 Repeatability of results
       5.3 Ordering inform
    6 Quality assurance
       6.1 General
       6.2 Standardization and operating procedures
       6.3 Equipment des
       6.4 Personnel qualification
       6.5 Dynamic test data demonstrating the system capabilities
             for detecting the reference indicators
       6.6 Reports
    7 Qualification of inspection personnel
       7.1 General
       7.2 Written procedure
       7.3 Qualification responsibility and requirements
       7.4 Training programmes
       7.5 Examinations
       7.6 Experience
       7.7 Re-qualification
       7.8 Documentation
       7.9 NDT personnel certification
    8 General inspection procedures
       8.1 General
       8.2 Owner/operator work site requirements for quality
             inspection
       8.3 Documents at job site
       8.4 Pre-inspection procedures
       8.5 Drill-pipe and tool-joint classification markings
       8.6 Post-inspection procedures
    9 General non-destructive inspection method requirements
       9.1 General
       9.2 Equipment
       9.3 Illumination
       9.4 Magnetic-particle-inspection equipment
       9.5 Ultrasonic
       9.6 Electromagnetic inspection units
    10 Drill stem element inspection and classification
       10.1 Pipe body - Full-length visual inspection
       10.2 Drill body - Outside diameter gauging
       10.3 Pipe body - Ultrasonic wall-thickness gauging
       10.4 Pipe body - Full-length electromagnetic inspection
             (EMI)
       10.5 Pipe body - Full-length ultrasonic transverse and wall
             thickness
       10.6 Pipe body - Full-length ultrasonic transverse, wall
             thickness and longitudinal inspection
       10.7 Drill-pipe body - External magnetic-particle inspection
             of the critical area
       10.8 Drill-pipe body - Bi-directional external magnetic-particle
             inspection of the critical area
       10.9 Pipe body - Full-length wall-loss inspection
       10.10 Pipe body - Ultrasonic inspection of the critical area
       10.11 Pipe body - Calculation of cross-sectional area
       10.12 Pipe body - Document review (traceability)
       10.13 Pipe body - Evaluation and classification
       10.14 Tool joints
       10.15 Tool joints - Check for box swell and pin stretch
       10.16 Repair of rejected tool joints
       10.17 Tool joints - Check tool-joint pin and box outside
             diameter and eccentric wear
       10.18 Tool joints - Measure tool-joint pin and box outside
             diameter and check for eccentric wear
       10.19 Tool joints - Check tool-joint pin and box tong space
       10.20 Tool joints - Measure tool-joint pin and box tong
             space
       10.21 Tool joint - Magnetic-particle inspection of the pin
             threads
       10.22 Tool joint - Magnetic-particle inspection of box
             threads
       10.23 Tool joints - Measure tool-joint pin inside diameter
       10.24 Magnetic-particle inspection of the connection OD for
             heat-check cracking
       10.25 Bi-directional wet magnetic-particle inspection of the
             connection OD for heat-check cracking
       10.26 Tool joints - Measure the tool-joint counterbore
             depth, pin-base length and seal width
       10.27 BHA connection - Visual inspection of bevels, seals,
             threads and stress-relief features
       10.28 BHA - Measure box outside diameter, pin inside
             diameter, counterbore diameter and benchmark l
             ocation if a benchmark is present
       10.29 BHA - Check bevel diameter
       10.30 BHA - Measure bevel diameter
       10.31 BHA - Magnetic-particle inspection of the pin and box
             threads
       10.32 BHA connection - Liquid-penetrant inspection of the
             pin and box threads
       10.33 BHA - Dimensional measurement of stress-relief
             features
       10.34 Length measurements of the counterbore, pin and pin
             neck
       10.35 Drill collar - Visual full-length OD and ID, markings,
             fish-neck length and tong space
       10.36 Drill-collar elevator groove and slip-recess
             magnetic-particle inspection
       10.37 Drill-collar elevator-groove and slip-recess
             measurement
       10.38 Subs (full-length visual OD and ID), fish-neck length,
             section-change radius and markings
       10.39 Float-bore recess measurements
       10.40 Magnetic-particle inspection of subs - Full-length,
             internal and external
       10.41 HWDP - Visual full-length OD and ID, markings and
             tong space
       10.42 Visual inspection and wear pattern report for kelly
       10.43 Magnetic-particle evaluation of critical areas on kellys
       10.44 Magnetic-particle evaluation, full length, of the drive
             section on kellys
       10.45 Stabilizer (full-length visual OD and ID), fish-neck
             length, blade condition, ring gauge and markings
       10.46 Magnetic-particle inspection of the base of stabilizer
             blades for cracking
       10.47 Function test
       10.48 Bi-directional, wet magnetic-particle inspection of the
             base of stabilizer blade for cracking
       10.49 Visual inspection of jars (drilling and fishing),
             accelerators and shock subs
       10.50 Maintenance review
       10.51 Dimensional measurement of wear areas as specified
             by OEM requirements
       10.52 Original equipment manufacturer designated testing
             for used equipment
       10.53 MWD/LWD - Visual, full-length OD and ID, and
             markings, including visual inspection of
             hard-banding and coatings
       10.54 Motors and turbines - Visual, full-length OD and ID
             and markings, including visual inspection of
             hard-banding and coatings
       10.55 Reamers, scrapers, and hole openers - Visual,
             full-length OD and ID and markings, including
             visual inspection of hard-banding and coatings
       10.56 Rotary steerable - Visual, full-length OD and ID
             and markings, including visual inspection of
             hard-banding
       10.57 Full-length drift
       10.58 Proprietary equipment inspection
       10.59 Hard-banding inspection
       10.60 Transverse magnetic-particle inspection of tool-joint
             OD and ID under the pin threads
       10.61 Drill-pipe body - Internal magnetic-particle inspection
             of the critical area
       10.62 Drill-pipe body - Bi-directional, internal
             magnetic-particle inspection of the critical
             area
       10.63 API external upset-thread connection inspection
    Annex A (normative) Original equipment manufacturer
            (OEM) requirements
    Annex B (normative) Required and additional inspections
            by product and class of service
    Annex C (normative) SI units
    Annex D (informative) USC units
    Annex E (informative) Inspection-level guidelines
    Annex F (informative) Proprietary drill stem connection
            inspection
    Annex G (informative) Used work-string tubing proprietary-connection
            thread inspection
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the required inspection for each level of inspection and procedures for the inspection and testing of used drill stem elements.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    ASNT SNT TC 1A : 2016 TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
    ISO/TS 29001:2010 Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations
    API 7-2 : 2017 THREADING AND GAUGING OF ROTARY SHOULDERED CONNECTIONS
    API 7A1 : 1992 RECOMMENDED PRACTICE FOR TESTING OF THREAD COMPOUND FOR ROTARY SHOULDERED CONNECTIONS
    API 7-1 : 2006 : ADD 3:2011(R2015) SPECIFICATION FOR ROTARY DRILL STEM ELEMENTS
    API Q1 : 2013 SPECIFICATION FOR QUALITY MANAGEMENT SYSTEM REQUIREMENTS FOR MANUFACTURING ORGANIZATIONS FOR THE PETROLEUM AND NATURAL GAS INDUSTRY
    API 7 : 2001 SPECIFICATION FOR ROTARY DRILL STEM ELEMENTS
    ISO 11484:2009 Steel products — Employer's qualification system for non-destructive testing (NDT) personnel
    ISO 9000:2015 Quality management systems Fundamentals and vocabulary
    ISO 10424-2:2007 Petroleum and natural gas industries Rotary drilling equipment Part 2: Threading and gauging of rotary shouldered thread connections
    ISO 10424-1:2004 Petroleum and natural gas industries Rotary drilling equipment Part 1: Rotary drill stem elements
    ASTM E 1220 : 2016 : REDLINE Standard Practice for Visible Penetrant Testing Using Solvent-Removable Process
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective