• There are no items in your cart

I.S. EN ISO 10414-2:2011

Current
Current

The latest, up-to-date edition.

PETROLEUM AND NATURAL GAS INDUSTRIES - FIELD TESTING OF DRILLING FLUIDS - PART 2: OIL-BASED FLUIDS
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2011

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Determination of drilling fluid density (mud weight)
6 Alternative method for determination of drilling fluid
   density
7 Viscosity and gel strength
8 Static filtration
9 Retort test for oil, water and solids concentrations
10 Chemical analysis of oil-based drilling fluids
11 Electrical stability test
12 Lime, salinity and solids calculations
Annex A (informative) - Measurement of shear strength using
        shearometer tube
Annex B (informative) - Determination of oil and water retained
        on cuttings
Annex C (informative) - Determination of aqueous-phase activity
        of emulsified water using an electrohygrometer
Annex D (informative) - Determination of aniline point
Annex E (informative) - Lime, salinity and solids calculations
Annex F (informative) - Sampling, inspection and rejection of
        drilling materials
Annex G (informative) - Rig-site sampling
Annex H (informative) - Determination of cutting activity by
        the Chenevert method
Annex I (informative) - Chemical analysis of active sulfides
        by the Garrett gas train method
Annex J (informative) - Calibration and verification of glassware,
        thermometers, viscometers, retort kit cup and drilling
        fluid balances
Annex K (informative) - High-temperature/high-pressure filtration
        testing of oil-based drilling fluids using the
        permeability plugging apparatus and cells equipped with
        set-screw secured end caps
Annex L (informative) - High-temperature/high-pressure
        filtration testing of oil-based drilling fluids using
        the permeability plugging apparatus and cells equipped
        with threaded end caps
Annex M (informative) - Compatibility of elastomeric materials
        with non-aqueous-based drilling fluids
Annex N (informative) - Sand content procedure for non-aqueous
        fluids
Annex O (informative) - Identification and monitoring of
        weight-material sag
Annex P (informative) - Oil-based drilling fluid report form
Bibliography

Gives standard procedures for determining the following characteristics of oil-based drilling fluids: - drilling fluid density (mud weight); - viscosity and gel strength; - filtration; - oil, water and solids concentrations; - alkalinity, chloride concentration and calcium concentration; - electrical stability; - lime and calcium concentrations, calcium chloride and sodium chloride concentrations; - low-gravity solids and weighting material concentrations.

DocumentType
Standard
Pages
171
PublisherName
National Standards Authority of Ireland
Status
Current

Standards Relationship
ISO 10414-2:2011 Identical
EN ISO 10414-2:2011 Identical

ISO 386:1977 Liquid-in-glass laboratory thermometers Principles of design, construction and use
ISO 2977:1997 Petroleum products and hydrocarbon solvents Determination of aniline point and mixed aniline point
API RP 13D : 2017 RHEOLOGY AND HYDRAULICS OF OIL-WELL DRILLING FLUIDS
ASTM D 3183 : 201 PRACTICE FOR RUBBER - PREPARATION OF PIECES FOR TEST PURPOSES FROM PRODUCTS
ISO 13226:2011 Rubber Standard reference elastomers (SREs) for characterizing the effect of liquids on vulcanized rubbers
ASTM D 3182 : 2016 : REDLINE Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets
ISO 13501:2011 Petroleum and natural gas industries Drilling fluids Processing equipment evaluation
ASTM D 471 : 2016-02 TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
ISO 10414-1:2008 Petroleum and natural gas industries — Field testing of drilling fluids — Part 1: Water-based fluids

View more information
US$202.81
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.