Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search

I.S. EN ISO 11296-4:2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES (ISO 11296-4:2018)
Available format(s)

Hardcopy , PDF

Superseded date

01-29-2020

Published date

03-05-2018

Publisher

National Standards Authority of Ireland

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the 'M' stage
6 Fittings at the 'M' stage
7 Ancillary components
8 Fitness for purpose of the installed lining
  system at the 'I' stage
9 Installation practice
Annex A (informative) - CIPP components and
        their functions
Annex B (normative) - Cured-in-place pipes -
        Determination of short-term flexural properties
Annex C (normative) - Cured-in-place pipes -
        Determination of long-term flexural
        modulus under dry or wet conditions
Annex D (normative) - Cured-in-place pipes -
        Determination of long-term flexural
        strength under dry, wet or acidic conditions
        (stress corrosion test)
Bibliography

Describes requirements and test methods for cured-inplace pipes and fittings used for the renovation of underground non-pressure drainage and sewerage networks with service temperatures up to 50 Degrees C.

Committee
TC 138
DevelopmentNote
Supersedes I.S. EN 13566-4. (05/2011)
DocumentType
Test Method
Pages
58
ProductNote
The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document.
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
EN ISO 11296-4:2018 Identical
EN ISO 11296-4:2011 Identical
ISO 11296-4:2018 Identical

ISO 8773:2006 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP)
ISO 7685:1998 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness
ISO 10467:2004 Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
ISO 10928:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ISO 13002:1998 Carbon fibre Designation system for filament yarns
ISO 8513:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength
ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
ISO 899-2:2003 Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading
ISO 14125:1998 Fibre-reinforced plastic composites Determination of flexural properties
ISO 7684:1997 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the creep factor under dry conditions
ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U)
EN 14364:2013 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
ISO 178:2010 Plastics Determination of flexural properties
ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics

View more information
US$70.16
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us