• There are no items in your cart

I.S. EN ISO 20029-2:2018

Current
Current

The latest, up-to-date edition.

PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES (ISO 20029-2:2017)
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2018

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Preparation of test specimens
5 Conditioning of test specimens
6 Determination of properties
Annex A (informative) - Determination of tensile properties
Bibliography

Defines the methods of preparation of test specimens and the standard test methods to be used in determining the properties of thermoplastic polyester/ester and polyether/ester elastomer moulding and extrusion materials.

DevelopmentNote
Supersedes I.S. EN ISO 14910-2. (03/2018)
DocumentType
Standard
Pages
34
PublisherName
National Standards Authority of Ireland
Status
Current
Supersedes

Standards Relationship
EN ISO 20029-2:2018 Identical

IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
ISO 16365-2:2014 Plastics Thermoplastic polyurethanes for moulding and extrusion Part 2: Preparation of test specimens and determination of properties
ISO 22007-3:2008 Plastics Determination of thermal conductivity and thermal diffusivity Part 3: Temperature wave analysis method
ISO 3167:2014 Plastics Multipurpose test specimens
ISO 22007-4:2017 Plastics — Determination of thermal conductivity and thermal diffusivity — Part 4: Laser flash method
ISO 974:2000 Plastics Determination of the brittleness temperature by impact
IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
ISO 815-1:2014 Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures
ISO 10350-1:2017 Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
ISO 8256:2004 Plastics — Determination of tensile-impact strength
ISO 11359-2:1999 Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
ISO 34-1:2015 Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 11357-3:2011 Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization
ISO 11357-4:2014 Plastics Differential scanning calorimetry (DSC) Part 4: Determination of specific heat capacity
ISO 294-4:2001 Plastics Injection moulding of test specimens of thermoplastic materials Part 4: Determination of moulding shrinkage
IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
ISO 1183-3:1999 Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method
ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 15512:2016 Plastics Determination of water content
ISO 62:2008 Plastics Determination of water absorption
ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 4589-2:2017 Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
ISO 22007-2:2015 Plastics Determination of thermal conductivity and thermal diffusivity Part 2: Transient plane heat source (hot disc) method
ISO 1133-2:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 20753:2008 Plastics Test specimens
ISO 178:2010 Plastics Determination of flexural properties
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)

View more information
US$40.56
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.