IEC 60079-5:2015 RLV
Current
Current
The latest, up-to-date edition.
Explosive atmospheres - Part 5: Equipment protection by powder filling "q"
Amended by
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Language(s)
English
Published date
02-17-2015
Publisher
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Constructional requirements
5 Verifications and tests
6 Marking
7 Instructions
Bibliography
IEC 60079-5:2015 RLV contains both the official IEC International Standard and its Redline version. The Redline version is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition.
IEC 60079-5:2015 contains specific requirements for the construction, testing and marking of electrical equipment, parts of electrical equipment and Ex components in the type of protection powder filling "q", intended for use in explosive gas atmospheres. This standard supplements and modifies the general requirements of IEC 60079-0. Where a requirement of this standard conflicts with a requirement of IEC 60079-0, the requirement of this standard takes precedence. This standard applies to electrical equipment, parts of electrical equipment and Ex components with:
- a rated supply current less than or equal to 16 A;
- a rated supply voltage less than or equal to 1 000 V;
- a rated power consumption less than or equal to 1 000 W.
This fourth edition cancels and replaces the third edition, published in 2007, and constitutes a technical revision. Refer to the Foreword of the document for a complete listing of the technical changes between edition 4.0 and previous edition of the document.
Keywords: electrical equipment and Ex components in the type of protection powder filling "q"
| Committee |
TC 31
|
| DevelopmentNote |
Stability date: 2021. (02/2015)
|
| DocumentType |
Redline
|
| Pages |
68
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN 60079-5 : 2015 | Identical |
| NBN EN 60079-5 : 2015 | Identical |
| NEN EN IEC 60079-5 : 2015 | Identical |
| AS/NZS 60079.5:2015 | Identical |
| UNE-EN 60079-5:2016 | Identical |
| BS EN 60079-5:2015 | Identical |
| CEI EN 60079-5 : 2015 | Identical |
| EN 60079-5:2015 | Identical |
| UNE 20321:1971 | Identical |
| BIS IS/IEC 60079-5 : 2007 | Identical |
| SAC GB 3836-7 : 2004 | Identical |
| GOST R IEC 60079-5 : 2012 | Identical |
| CSA E60079.5 : 2002 | Similar to |
| NEN EN 50017 : 1998 | Identical |
| EN 50017:1998 | Identical |
| BS 5501-4:1977 | Identical |
| CSA E60079.5 : 2002 : R2011 | Similar to |
| VDE 0170-4 : 2015 | Identical |
| DIN EN 60079-5 : 2015 | Identical |
| SANS 60079-5 : 3ED 2009 | Identical |
| PN EN 60079-5 : 2015 | Identical |
| IEEE 303-2004 | IEEE Recommended Practice for Auxiliary Devices for Rotating Electrical Machines in Class I, Division 2 and Zone 2 Locations |
| UNE-EN 60079-17:2014 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
| CEN/TR 16787:2014 | Industrial Gas Installation - Guideline |
| UNI EN 1474-1 : 2009 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| BS EN 60079-17:2014 | Explosive atmospheres Electrical installations inspection and maintenance |
| BS ISO 12643-1:2009 | Graphic technology. Safety requirements for graphic technology equipment and systems General requirements |
| I.S. EN 60079-0:2012 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011 (MOD)) |
| 12/30268608 DC : 0 | BS EN 60079-17/ED 5 - EXPLOSIVE ATMOSPHERES - PART 17: ELECTRICAL INSTALLATIONS INSPECTION AND MAINTENANCE |
| 12/30260078 DC : 0 | BS EN 60092-502 IEC 60092-502 - ELECTRICAL INSTALLATIONS IN SHIPS - PART 502: TANKERS - SPECIAL FEATURES |
| CSA C22.2 No. 60079.0 : 2015 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS |
| UNE-EN 12405-1:2006 | Gas meters - Conversion devices - Part 1: Volume conversion |
| 18/30369304 DC : DRAFT APR 2018 | BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| IEC 60079-0 REDLINE : 7.0 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS |
| S.R. CEN/TR 16787:2014 | INDUSTRIAL GAS INSTALLATION - GUIDELINE |
| ISO/IEC 80079-38:2016 | Explosive atmospheres Part 38: Equipment and components in explosive atmospheres in underground mines |
| CSA C22.2 No. 60079-18 : 2016 | EXPLOSIVE ATMOSPHERES - PART 18: EQUIPMENT PROTECTION BY ENCAPSULATION 'M' |
| DIN EN ISO/IEC 80079-38:2012-08 (Draft) | EXPLOSIVE ATMOSPHERES - PART 38: EQUIPMENT AND COMPONENTS IN EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES (ISO/IEC 80079-38:2016) |
| 16/30341165 DC : 0 | BS EN 14492-2 - CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
| EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| AAMI ES60601-1 : 2005 : INC : AMD 1 : 2012 : R201200 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
| AAMI ES60601-1 : 2005 : INC : AMD 2 : 2012 : R201200 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
| AAMI ES60601-1 : 2005 : R2012 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
| DIN EN 1473:2016-10 | Installation and equipment for liquefied natural gas - Design of onshore installations |
| BS EN 60079-18 : 2015 | EXPLOSIVE ATMOSPHERES - PART 18: EQUIPMENT PROTECTION BY ENCAPSULATION 'M' |
| DIN EN 13922:2011-11 | TANKS FOR TRANSPORT OF DANGEROUS GOODS - SERVICE EQUIPMENT FOR TANKS - OVERFILL PREVENTION SYSTEMS FOR LIQUID FUELS |
| DIN EN 12312-5:2009-08 | Aircraft ground support equipment - Specific requirements - Part 5: Aircraft fuelling equipment (includes Amendment A1:2009) |
| EN 1010-1:2004+A1:2010 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements |
| EN 12621:2006+A1:2010 | Machinery for the supply and circulation of coating materials under pressure - Safety requirements |
| EN 60079-2:2014/AC:2015 | EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014) |
| DEFSTAN 00-101(PT3)/1(2005) : 2005 | DESIGN STANDARDS FOR EXPLOSIVES SAFETY IN MOD SHIPS AND SUBMARINES - PART 3: ELECTRICAL EQUIPMENT AND INSTALLATION |
| DEFSTAN 00-101(PT3)/2(2008) : 2008 | DESIGN STANDARDS FOR EXPLOSIVES SAFETY IN MOD SHIPS AND SUBMARINES - PART 3: ELECTRICAL EQUIPMENT AND INSTALLATION |
| BS EN 16299:2013 | Cathodic protection of external surfaces of above ground storage tankbases in contact with soil or foundations |
| PREN 12405-1 : DRAFT 2017 | GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| 03/300201 DC : DRAFT FEB 2003 | IEC 60079-0 ED.4.0 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 0: GENERAL REQUIREMENTS |
| I.S. EN 60079-2:2014 | EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' |
| EN 60079-29-1:2016 | Explosive atmospheres - Part 29-1: Gas detectors - Performance requirements of detectors for flammable gases |
| BS IEC 60092-502:1999 | Electrical installation in ships Tankers. Special features |
| I.S. EN 1474-1:2008 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| ISA 12.13.01 : 2003 | PERFORMANCE REQUIREMENTS FOR COMBUSTIBLE GAS DETECTORS |
| BS EN 60079-29-1:2007 | Explosive atmospheres Gas detectors. Performance requirements of detectors for flammable gases |
| I.S. EN 61779-1:2003 | ELECTRICAL APPARATUS FOR THE DETECTION AND MEASUREMENT OF FLAMMABLE GASES - PART 1: GENERAL REQUIREMENTS AND TEST METHODS |
| BS EN ISO/IEC 80079-38 : 2016 | EXPLOSIVE ATMOSPHERES - PART 38: EQUIPMENT AND COMPONENTS IN EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES (ISO/IEC 80079 38:2016) |
| ISO 10574:1993 | Refrigerated light-hydrocarbon fluids — Measurement of liquid levels in tanks containing liquefied gases — Float-type level gauges |
| UNE-EN 60079-29-1:2017 | Explosive atmospheres - Part 29-1: Gas detectors - Performance requirements of detectors for flammable gases |
| I.S. EN 60079-18:2015 | EXPLOSIVE ATMOSPHERES - PART 18: EQUIPMENT PROTECTION BY ENCAPSULATION 'M' |
| I.S. EN 13616-1:2016 | OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID FUELS -PART 1: OVERFILL PREVENTION DEVICES WITH CLOSURE DEVICE |
| AAMI ES60601-1 : 2005 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
| DIN EN 1010-1:2011-06 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements (includes Amendment A1:2010) |
| DIN EN 12621:2011-07 | Machinery for the supply and circulation of coating materials under pressure - Safety requirements (includes Amendment A1:2010) |
| DIN EN 12581:2011-02 | Coating plants - Machinery for dip coating and electrodeposition of organic liquid coating material - Safety requirements (includes Amendment A1:2010) |
| DIN EN 13617-1:2012-08 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| 09/30206527 DC : 0 | BS EN 60079-0 ED 6.0 - EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS |
| BS EN 1473:2016 | Installation and equipment for liquefied natural gas. Design of onshore installations |
| IEC 61779-1:1998 | Electrical apparatus for the detection and measurement of flammable gases - Part 1: General requirements and test methods |
| BIS IS/IEC 60079-0 : 2011 | EXPLOSIVE ATMOSPHERES - PART 0: GENERAL REQUIREMENTS |
| DIN EN 1473:1997-11 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| I.S. EN 13852-1:2013 | CRANES - OFFSHORE CRANES - PART 1: GENERAL - PURPOSE OFFSHORE CRANES |
| I.S. EN 12621:2006 | MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS |
| I.S. EN 12312-5:2005 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| I.S. EN 1473:2016 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| EN 12312-5:2005+A1:2009 | Aircraft ground support equipment - Specific requirements - Part 5: Aircraft fuelling equipment |
| I.S. EN 13617-1:2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| EN 60079-14:2014/AC:2016 | EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016) |
| I.S. EN 1010-1:2005 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| I.S. EN 12581:2006 | COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS |
| VDI/VDE 3518 Blatt 1:2011-05 | Multigas sensors - Terms, configuration, function and classification |
| BS 5724-1(1989) : 1989 AMD 6715 | MEDICAL ELECTRICAL EQUIPMENT - GENERAL REQUIREMENTS FOR SAFETY |
| BIS IS/IEC 60079-18 : 2009 | EXPLOSIVE ATMOSPHERES - PART 18: EQUIPMENT PROTECTION BY ENCAPSULATION 'M' |
| DIN EN 61779-1 : 2001 AMD 11 2004 | ELECTRICAL APPARATUS FOR THE DETECTION AND MEASUREMENT OF FLAMMABLE GASES - PART 1: GENERAL REQUIREMENTS AND TEST METHODS |
| OVE/ONORM EN 60601-1 : 2014 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005 + COR.:2006 + COR.:2007 + A1:2012) |
| UNE-EN 13616-1:2016 | Overfill prevention devices for static tanks for liquid fuels - Part 1: Overfill prevention devices with closure device |
| CSA C22.4 No. 1 : 2009(R2018) | OBJECTIVE-BASED INDUSTRIAL ELECTRICAL CODE |
| DIN EN 1474-1:2009-03 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| PREN 1473 : DRAFT 2018 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| ISO 12643-1:2009 | Graphic technology — Safety requirements for graphic technology equipment and systems — Part 1: General requirements |
| PREN 13617-1 : DRAFT 2010 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| PREN 14492-1 : DRAFT 2015 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
| 10/30219405 DC : 0 | BS EN 13617-1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| ISO 12648:2006 | Graphic technology Safety requirements for printing press systems |
| 13/30286135 DC : 0 | BS EN 13616-1 - OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID FUELS - REQUIREMENTS AND TEST/ASSESSMENT METHODS - PART 1: OVERFILL PREVENTION DEVICES WITH CLOSURE DEVICE |
| 10/30212177 DC : 0 | BS EN 12405-1:2005/A2 - GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| EN 1473:2016 | Installation and equipment for liquefied natural gas - Design of onshore installations |
| ISO 12649:2004 | Graphic technology Safety requirements for binding and finishing systems and equipment |
| NF ISO 14661 : 2000 AMD 1 2004 | THERMAL TURBINES FOR INDUSTRIAL APPLICATIONS (STEAM TURBINES, GAS EXPANSION TURBINES) - GENERAL REQUIREMENTS |
| 05/30128234 DC : DRAFT FEB 2005 | EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| UNI EN 12405-1 : 2010 | GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| BS ISO 14839-4:2012 | Mechanical vibration. Vibration of rotating machinery equipped with active magnetic bearings Technical guidelines |
| CEI EN 60079-17 : 2015 | EXPLOSIVE ATMOSPHERES - PART 17: ELECTRICAL INSTALLATIONS INSPECTION AND MAINTENANCE |
| 09/30209043 DC : 0 | BS EN 13922 - TANKS FOR TRANSPORT OF DANGEROUS GOODS - SERVICE EQUIPMENT FOR TANKS - OVERFILL PREVENTION SYSTEMS FOR LIQUID FUELS |
| 08/30174143 DC : DRAFT SEP 2008 | BS EN 12312-5 AMD1 - AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| UNE-EN ISO 16904:2016 | Petroleum and natural gas industries - Design and testing of LNG marine transfer arms for conventional onshore terminals (ISO 16904:2016) |
| 04/30112677 DC : 0 | IEC 61779-1 ED.2 - ELECTRICAL APPARATUS FOR THE DETECTION AND MEASUREMENT OF FLAMMABLE GASES - PART 1: GENERAL REQUIREMENTS AND TEST METHODS |
| PD CEN/TR 16787:2014 | Industrial Gas Installation. Guideline |
| BS ISO 12648:2006 | Graphic technology. Safety requirements for printing press systems |
| CSA PLUS 2203 : 2001 | HAZARDOUS LOCATIONS - GUIDE FOR THE DESIGN, TESTING, CONSTRUCTION, AND INSTALLATION OF EQUIPMENT IN EXPLOSIVE ATMOSPHERES |
| BS EN 60079-2:2014 | Explosive atmospheres Equipment protection by pressurized enclosure \'p\' |
| NF EN 1474-1 : 2009 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| ISO 8309:1991 | Refrigerated light hydrocarbon fluids Measurement of liquid levels in tanks containing liquefied gases Electrical capacitance gauges |
| IEC 61779-6:1999 | Electrical apparatus for the detection and measurement of flammable gases - Part 6: Guide for the selection, installation, use and maintenance of apparatus for the detection and measurement of flammable gases |
| CSA C22.2 No. 60601.1 : 2014 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| CSA E60079.0 : 2002 | ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - GENERAL REQUIREMENTS |
| I.S. EN 60079-17:2014 | EXPLOSIVE ATMOSPHERES - PART 17: ELECTRICAL INSTALLATIONS INSPECTION AND MAINTENANCE |
| I.S. EN 12405-1:2005 | GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| UNI EN 16299 : 2013 | CATHODIC PROTECTION OF EXTERNAL SURFACES OF ABOVE GROUND STORAGE TANK BASES IN CONTACT WITH SOIL OR FOUNDATIONS |
| EN ISO/IEC 80079-38:2016 | Explosive atmospheres - Part 38: Equipment and components in explosive atmospheres in underground mines (ISO/IEC 80079-38:2016) |
| IEC 60079-18:2014 RLV | Explosive atmospheres - Part 18: Equipment protection by encapsulation “m” |
| EEMUA 186 : 2016 | A PRACTITIONER'S HANDBOOK FOR POTENTIALLY EXPLOSIVE ATMOSPHERES |
| DIN EN 12312-5 E : 2009 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| UNE-EN 60079-14:2016 | Explosive atmospheres - Part 14: Electrical installations design, selection and erection |
| BS EN 1010-1 : 2004 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| BS EN 12312-5 : 2005 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| I.S. EN 13922:2011 | TANKS FOR TRANSPORT OF DANGEROUS GOODS - SERVICE EQUIPMENT FOR TANKS - OVERFILL PREVENTION SYSTEMS FOR LIQUID FUELS |
| ISO 16904:2016 | Petroleum and natural gas industries Design and testing of LNG marine transfer arms for conventional onshore terminals |
| BS EN 60079-14:2014 | Explosive atmospheres Electrical installations design, selection and erection |
| UNE-EN 60601-1:2008 | Medical electrical equipment -- Part 1: General requirements for basic safety and essential performance |
| EN 1474-1:2008 | Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 1: Design and testing of transfer arms |
| EN 16299:2013 | Cathodic protection of external surfaces of above ground storage tank bases in contact with soil or foundations |
| UNI EN 13617-1 : 2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| UNI EN 1010-1 : 2011 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| CSA E60079.14 : 2002 | ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - ELECTRICAL INSTALLATIONS IN EXPLOSIVE GAS ATMOSPHERES (OTHER THAN MINES) |
| UNI EN 13852-1 : 2013 | CRANES - OFFSHORE CRANES - PART 1: GENERAL-PURPOSE OFFSHORE CRANES |
| UNI EN 12621 : 2010 | MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS |
| DIN EN ISO/IEC 80079-38 E : 2017 | EXPLOSIVE ATMOSPHERES - PART 38: EQUIPMENT AND COMPONENTS IN EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES (ISO/IEC 80079-38:2016) |
| CSA C22.4 PACKAGE : 2009 | CONSISTS OF C22.4 NO. 1-09, OBJECTIVE-BASED INDUSTRIAL ELECTRICAL CODE AND C22.4 NO. 2-09, OBJECTIVE-BASED INDUSTRIAL ELECTRICAL CODE - SAFETY MANAGEMENT SYSTEM REQUIREMENTS |
| 04/30110212 DC : DRAFT MAR 2004 | ISO 12648 - GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR PRINTING PRESS SYSTEMS |
| 10/30214970 DC : 0 | BS EN 13616 - OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID PETROLEUM FUELS |
| BS ISO 12649:2004 | Graphic technology. Safety requirements for binding and finishing systems and equipment |
| I.S. EN 16299:2013 | CATHODIC PROTECTION OF EXTERNAL SURFACES OF ABOVE GROUND STORAGE TANK BASES IN CONTACT WITH SOIL OR FOUNDATIONS |
| 08/30190505 DC : 0 | BS ISO 12643-1 - GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR GRAPHIC TECHNOLOGY EQUIPMENT AND SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| 12/30243465 DC : 0 | BS ISO/IEC 80079-38 - EXPLOSIVE ATMOSPHERES - PART 38: EQUIPMENT AND COMPONENTS IN EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES |
| ISO 14839-4:2012 | Mechanical vibration — Vibration of rotating machinery equipped with active magnetic bearings — Part 4: Technical guidelines |
| BS EN 1474-1:2008 | Installation and equipment for liquefied natural gas. Design and testing of marine transfer systems Design and testing of transfer arms |
| 13/30278077 DC : 0 | BS EN ISO 16904 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND TESTING OF LNG MARINE TRANSFER ARMS FOR CONVENTIONAL ONSHORE TERMINALS |
| BS EN 13616-1:2016 | Overfill prevention devices for static tanks for liquid fuels Overfill prevention devices with closure device |
| 09/30182347 DC : 0 | BS EN 12621:2006/A1 - MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS |
| 09/30194936 DC : DRAFT JAN 2009 | BS EN ISO 28460 - PETROLEUM AND NATURAL GAS INDUSTRIES - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - SHIP-TO-SHORE INTERFACE AND PORT OPERATIONS |
| IEC 60079-0:2017 | Explosive atmospheres - Part 0: Equipment - General requirements |
| BS 7701:1993 | Specification for float-type level gauges for measuring liquid levels in tanks containing refrigerated light-hydrocarbon fluids |
| UNE-EN 16299:2013 | Cathodic protection of external surfaces of above ground storage tank bases in contact with soil or foundations |
| BS EN 12405-1 : 2005 | GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| PD IEC/TR 60601-4-3:2015 | Medical electrical equipment Guidance and interpretation. Considerations of unaddressed safety aspects in the third edition of IEC 60601-1 and proposals for new requirements |
| I.S. EN 60601- 1:2006&A1:2013&AC:2014&A12:2014 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| I.S. EN ISO/IEC 80079-38:2016 | EXPLOSIVE ATMOSPHERES - PART 38: EQUIPMENT AND COMPONENTS IN EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES (ISO/IEC/DIS 80079-38:2012) |
| CSA C22.2 No. 60079-2 : 2016 | EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' |
| EN 12405-1:2005+A2:2010 | Gas meters - Conversion devices - Part 1: Volume conversion |
| IEC 61892-7:2014 | Mobile and fixed offshore units - Electrical installations - Part 7: Hazardous areas |
| EN 13922:2011 | Tanks for transport of dangerous goods - Service equipment for tanks - Overfill prevention systems for liquid fuels |
| DIN EN 13852-1:2014-01 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
| BS EN 60601-1 : 2006 | MEDICAL ELECTRICAL EQUIPMENT PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| UNE-EN 12621:2006 | Machinery for the supply and circulation of coating materials under pressure - Safety requirements |
| BS EN 13617-1:2012 | Petrol filling stations Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| BS EN 12621 : 2006 | MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS |
| 05/30138005 DC : DRAFT AUG 2005 | IEC 60079-14 ED 4 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS IN HAZARDOUS AREAS (OTHER THAN MINES) |
| UNE-EN 60079-0:2013 | Explosive atmospheres - Part 0: Equipment - General requirements |
| 12/30276304 DC : 0 | BS EN 61892-7 ED 3.0 - MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 7: HAZARDOUS AREAS |
| UNE-EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| 05/30134569 DC : DRAFT JUN 2005 | IEC 60079-0. ED. 5.0 - ELECTRICAL APPARATUS FOR EXPLOSIVE ATMOSPHERES - PART 0: GENERAL REQUIREMENTS |
| 13/30271432 DC : 0 | BS EN 60079-18 ED 4.0 - EXPLOSIVE ATMOSPHERES - PART 18: EQUIPMENT PROTECTION BY ENCAPSULATION 'M' |
| BS EN 13922:2011 | Tanks for transport of dangerous goods. Service equipment for tanks. Overfill prevention systems for liquid fuels |
| 04/30106146 DC : DRAFT MARCH 2004 | BS EN 60601-1 - MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| UNE-EN 60079-2:2015 | Explosive atmospheres - Part 2: Equipment protection by pressurized enclosure "p" |
| UNE-EN 13922:2012 | Tanks for transport of dangerous goods - Service equipment for tanks - Overfill prevention systems for liquid fuels |
| UNE-EN 13852-1:2014 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
| EI Model code of safe practice Part 15:2015 | MODEL CODE OF SAFE PRACTICE - PART 15: AREA CLASSIFICATION FOR INSTALLATIONS HANDLING FLAMMABLE FLUIDS |
| EN ISO 16904:2016 | Petroleum and natural gas industries - Design and testing of LNG marine transfer arms for conventional onshore terminals (ISO 16904:2016) |
| EN 12581:2005+A1:2010 | Coating plants - Machinery for dip coating and electrodeposition of organic liquid coating material - Safety requirements |
| EN 13616-1:2016 | Overfill prevention devices for static tanks for liquid fuels - Part 1: Overfill prevention devices with closure device |
| EN 13852-1:2013 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
| SAE J 2578 : 2014 | RECOMMENDED PRACTICE FOR GENERAL FUEL CELL VEHICLE SAFETY |
| BS EN ISO 16904:2016 | Petroleum and natural gas industries. Design and testing of LNG marine transfer arms for conventional onshore terminals |
| BIS IS/IEC 60079-1 : 2007 | EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D' |
| 03/301332 DC : DRAFT JAN 2003 | ISO 12649 - GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR BINDING AND FINISHING SYSTEMS AND EQUIPMENT |
| 13/30267536 DC : 0 | BS EN 60079-29-1 ED 2.0 - EXPLOSIVE ATMOSPHERES - PART 29-1: GAS DETECTORS - PERFORMANCE REQUIREMENTS OF DETECTORS FOR FLAMMABLE GASES |
| BIS IS/ISO 12643-1 : 2009 | GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR GRAPHIC TECHNOLOGY EQUIPMENT AND SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| IEC 60309-3:1994 | Plugs, socket-outlets and couplers for industrial purposes - Part 3: Particular requirements for plugs, socket-outlets, connectors and appliance inlets for use in explosive gas atmospheres |
| I.S. EN 60079-14:2014 | EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION |
| 08/30186475 DC : 0 | BS EN 13617-1 AMD1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| 11/30247086 DC : 0 | BS EN 60079-1 ED. 7.0 - EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES "D" |
| 14/30297213 DC : 0 | BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| BS EN 61779-1:2000 | Electrical apparatus for the detection and measurement of flammable gases General requirements and test methods |
| I.S. EN ISO 16904:2016 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND TESTING OF LNG MARINE TRANSFER ARMS FOR CONVENTIONAL ONSHORE TERMINALS (ISO 16904:2016) |
| I.S. EN 60079-29-1:2016 | EXPLOSIVE ATMOSPHERES - PART 29-1: GAS DETECTORS - PERFORMANCE REQUIREMENTS OF DETECTORS FOR FLAMMABLE GASES |
| EN 60079-18:2015/A1:2017 | EXPLOSIVE ATMOSPHERES - PART 18: EQUIPMENT PROTECTION BY ENCAPSULATION 'M' (IEC 60079-18:2014/A1:2017) |
| BS EN 60079-0 : 2012 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS |
| 17/30356731 DC : 0 | BS EN 12405-1 - GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| IEC 60079-18 : 2014 REDLINE | EXPLOSIVE ATMOSPHERES - PART 18: EQUIPMENT PROTECTION BY ENCAPSULATION 'M' |
| PD 60079-14:2000 | Guide to application of BS EN 60079-14 |
| DIN EN 12405-1:2011-04 | GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| IEC 60079-17:2013 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
| BS EN 12581 : 2005 | COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS |
| 12/30269297 DC : 0 | BS EN 60079-14/ED 5 - EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION |
| 13/30286778 DC : 0 | BS EN 60079-1 - EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D' |
| BS IEC 61892-7:2014 | Mobile and fixed offshore units. Electrical installations Hazardous areas |
| BS EN 13852-1:2013 | Cranes. Offshore cranes General-purpose offshore cranes |
| IEC 60079-0:2017 RLV | Explosive atmospheres - Part 0: Equipment - General requirements |
| IEC 60601-1:2005+AMD1:2012 CSV | Medical electrical equipment - Part 1: General requirements for basic safety and essential performance |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| EN 60079-17:2014 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
| EN 61779-1 : 2000 AMD 11 2004 | ELECTRICAL APPARATUS FOR THE DETECTION AND MEASUREMENT OF FLAMMABLE GASES - PART 1: GENERAL REQUIREMENTS AND TEST METHODS |
| ISO 3310-1:2016 | Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth |
| ISO 3310-2:2013 | Test sieves — Technical requirements and testing — Part 2: Test sieves of perforated metal plate |
| ISO 2591-1:1988 | Test sieving — Part 1: Methods using test sieves of woven wire cloth and perforated metal plate |
| IEC 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| IEC 60050-426:2008 | International Electrotechnical Vocabulary (IEV) - Part 426: Equipment for explosive atmospheres |
| IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| IEC 61558-1:2017 | Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| IEC 60747-5-5:2007+AMD1:2013 CSV | Semiconductor devices - Discrete devices - Part 5-5: Optoelectronic devices - Photocouplers |
| IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
US$226.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
PDF 3 Users - English
PDF 5 Users - English
PDF 9 Users - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.