• There are no items in your cart

IEC 60751:2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Industrial platinum resistance thermometers and platinum temperature sensors
Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

01-27-2022

Language(s)

English - French

Published date

07-17-2008

IEC 60751:2008 specifies the requirements and temperature/resistance relationship for industrial platinum resistance temperature sensors later referred to as "platinum resistors" or "resistors" and industrial platinum resistance thermometers later referred to as "thermometers" whose electrical resistance is a defined function of temperature. Values of temperature in this standard are in terms of the International Temperature Scale of 1990, ITS-90. Temperatures in degrees Celsius are denoted by the symbol t, except in Table 1 where the full nomenclature t90/°C is used. The standard covers resistors or thermometers for all or part of the temperature range 200 °C to +850 °C with different tolerance classes, which may cover restricted temperature ranges. This second edition cancels and replaces the first edition published in 1983, amendment 1 (1986) and amendment 2 (1995). It constitutes a technical revision. The significant technical changes with respect to the previous edition are as follows: While the temperature/resistance relationship in 4.2 remains unchanged, there are several changes in the other chapters. Most important are: tolerance classes follow a new scheme; tolerance acceptance test is included; hysteresis test is included; several changes in the individual tests; appendices are deleted.

Committee
TC 65/SC 65B
DevelopmentNote
Supersedes RM.AERO 80121. (05/2015) Stability Date: 2017. (09/2017)
DocumentType
Standard
Pages
41
PublisherName
International Electrotechnical Committee
Status
Superseded
SupersededBy
Supersedes

NF EN 1434-2 : 2016 HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
17/30363953 DC : 0 BS EN 416 - GAS-FIRED OVERHEAD RADIANT TUBE HEATERS AND RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
02/124462 DC : DRAFT DEC 2002 BS EN 285 - STERILIZATION - STEAM STERILIZERS - LARGE STERILIZERS
BS EN 60068-3-7:2002 Environmental testing. Guidance Measurements in temperature chambers for tests A and B (with load)
12/30261215 DC : 0 BS EN 13060 - SMALL STEAM STERILIZERS
15/30291038 DC : 0 BS ISO 19291 - TESTING OF LUBRICANTS - TRIBOLOGICAL TEST IN THE TRANSLATORY OSCILLATION APPARATUS - DETERMINATION OF TRIBOLOGICAL QUANTITIES FOR OILS AND GREASES IN THE TRANSLATORY OSCILLATION APPARATUS
CSA C900.5 : 2013 HEAT METERS - PART 5: INITIAL VERIFICATION TESTS
NF EN 1434-4 : 2016 HEAT METERS - PART 4: PATTERN APPROVAL TESTS
16/30312922 DC : 0 BS ISO 18888 - GAS TURBINE COMBINED CYCLE POWER PLANTS THERMAL PERFORMANCE TESTS
14/30291768 DC : 0 BS EN 1434-4 - HEAT METERS - PART 4: PATTERN APPROVAL TESTS
I.S. EN 61987-1:2007 INDUSTRIAL-PROCESS MEASUREMENT AND CONTROL - DATA STRUCTURES AND ELEMENTS IN PROCESS EQUIPMENT CATALOGUES - PART 1: MEASURING EQUIPMENT WITH ANALOGUE AND DIGITAL OUTPUT
PD ISO/TR 9464:2008 Guidelines for the use of ISO 5167:2003
14/30291756 DC : 0 BS EN 1434-2 - HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
BS EN 60068-3-6:2002 Environmental testing. Guidance Confirmation of the performance of temperature/humidity chambers
PREN 14180 : DRAFT 2012 STERILIZERS FOR MEDICAL PURPOSES - LOW TEMPERATURE STEAM AND FORMALDEHYDE STERILIZERS - REQUIREMENTS AND TESTING
IEC 60350-2:2017 Household electric cooking appliances - Part 2: Hobs - Methods for measuring performance
BS ISO 4625-1 : 2004 AMD 16196 BINDERS FOR PAINTS AND VARNISHES - DETERMINATION OF SOFTENING POINT - PART 1: RING-AND-BALL METHOD
16/30312501 DC : 0 BS ISO 19618 - FINE CERAMICS (ADVANCED CERAMICS, ADVANCED TECHNICAL CERAMICS) - MEASUREMENT METHOD FOR NORMAL SPECTRAL EMISSIVITY USING BLACKBODY REFERENCE WITH AN FTIR SPECTROMETER
IP 527 : 2015 PETROLEUM PRODUCTS AND LUBRICANTS - DETERMINATION OF LOW-TEMPERATURE CONE PENETRATION OF LUBRICATING GREASES
PREN 285 : DRAFT 2013 STERILIZATION - STEAM STERILIZERS - LARGE STERILIZERS
AAMI ISO 11140-4 : 2007 STERILIZATION OF HEALTH CARE PRODUCTS - CHEMICAL INDICATORS - PART 4: CLASS 2 INDICATORS AS AN ALTERNATIVE TO THE BOWIE AND DICK-TYPE TEST FOR DETECTION OF STEAM PENETRATION
CEI EN 60068-3-7 : 2002 ENVIRONMENTAL TESTING - PART 3-7: SUPPORTING DOCUMENTATION AND GUIDANCE MEASUREMENTS IN TEMPERATURE CHAMBERS FOR TEST A AND B (WITH LOAD)
BS ISO 13737:2004 Method of test for petroleum and its products. BS 2000-527. Petroleum products and lubricants. Determination of low-temperature cone penetration of lubricating greases
EN 60350-2:2018 Household electric cooking appliances - Part 2: Hobs - Methods for measuring performance
PREN 13060 : DRAFT 2012 SMALL STEAM STERILIZERS
UNE-EN 12405-1:2006 Gas meters - Conversion devices - Part 1: Volume conversion
IEEE 3004.8-2016 IEEE Recommended Practice for Motor Protection in Industrial and Commercial Power Systems
ONORM EN ISO 18472 : 2006 STERILIZATION OF HEALTH CARE PRODUCTS - BIOLOGICAL AND CHEMICAL INDICATORS - TEST EQUIPMENT
I.S. EN ISO 15970:2014 NATURAL GAS - MEASUREMENT OF PROPERTIES - VOLUMETRIC PROPERTIES: DENSITY, PRESSURE, TEMPERATURE AND COMPRESSION FACTOR (ISO 15970:2008)
OIML R 75-1 : 2002 HEAT METERS - PART 1: GENERAL REQUIREMENTS
ISO 6182-1:2014 Fire protection Automatic sprinkler systems Part 1: Requirements and test methods for sprinklers
NF EN 60947-8 : 2003 AMD 2 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 8: CONTROL UNITS FOR BUILT-IN THERMAL PROTECTION (PTC) FOR ROTATING ELECTRICAL MACHINES
I.S. EN 1434-4:2015 HEAT METERS - PART 4: PATTERN APPROVAL TESTS
ISO 19291:2016 Lubricants — Determination of tribological quantities for oils and greases — Tribological test in the translatory oscillation apparatus
BS EN 1434-1 : 2015 HEAT METERS - PART 1: GENERAL REQUIREMENTS
NF EN 60068-3-6 : 2002 ENVIRONMENTAL TESTING - PART 3-6: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE/HUMIDITY CHAMBERS
ASTM D 5771 : 2017 : REDLINE Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Optical Detection Stepped Cooling Method)
EN 285:2015 Sterilization - Steam sterilizers - Large sterilizers
DIN EN ISO 11140-4:2007-07 Sterilization of health care products - Chemical indicators - Part 4: Class 2 indicators as an alternative to the Bowie and Dick-type test for detection of steam penetration (ISO 11140-4:2007)
BS EN 12952-15:2003 Water-tube boilers and auxiliary installations Acceptance tests
PD CEN/TR 15177:2006 Testing the freeze-thaw resistance of concrete. Internal structural damage
BS EN ISO 4625-1:2006 Binders for paint and varnishes. Determination of softening point Ring-and-ball method
IEC 60068-3-5:2018 RLV Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers
EN ISO 2719:2016 Determination of flash point - Pensky-Martens closed cup method (ISO 2719:2016)
EN 12953-11:2003 Shell boilers - Part 11: Acceptance tests
IEC 60068-3-6:2018 RLV Environmental testing - Part 3-6: Supporting documentation and guidance - Confirmation of the performance of temperature/ humidity chambers
EN 12259-1:1999 + A1:2001/A3:2006 FIXED FIREFIGHTING SYSTEMS - COMPONENTS FOR SPRINKLER AND WATER SPRAY SYSTEMS - PART 1: SPRINKLERS
EN 60947-8:2003/A2:2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 8: CONTROL UNITS FOR BUILT-IN THERMAL PROTECTION (PTC) FOR ROTATING ELECTRICAL MACHINES (IEC 60947-8:2003/A2:2011)
EN 12599:2012 Ventilation for buildings - Test procedures and measurement methods to hand over air conditioning and ventilation systems
NF EN 285 : 2016 STERILIZATION - STEAM STERILIZERS - LARGE STERILIZERS
CEN/TR 15177:2006 Testing the freeze-thaw resistance of concrete - Internal structural damage
CEN/TS 12390-9:2016 Testing hardened concrete - Part 9: Freeze-thaw resistance with de-icing salts - Scaling
DIN EN 14705:2005-10 Heat exchangers - Method of measurement and evaluation of thermal performances of wet cooling towers; German version EN 14705:2005
EN 60068-3-6:2002 Environmental testing - Part 3-6: Supporting documentation and guidance - Confirmation of the performance of temperature/humidity chambers
ASME BPE : 2016 BIOPROCESSING EQUIPMENT
BS EN ISO 2592:2017 Petroleum and related products. Determination of flash and fire points. Cleveland open cup method
12/30248648 DC : DRAFT AUG 2012 BS EN 16442 - CONTROLLED ENVIRONMENT STORAGE CABINET FOR DISINFECTED THERMOLABILE ENDOSCOPES
PREN 416 : DRAFT 2017 GAS-FIRED OVERHEAD RADIANT TUBE HEATERS AND RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
12/30262894 DC : 0 BS EN 14180 - STERILIZERS FOR MEDICAL PURPOSES - LOW TEMPERATURE STEAM AND FORMALDEHYDE STERILIZERS - REQUIREMENTS AND TESTING
16/30339586 DC : 0 BS EN 60068-3-6 - ENVIRONMENTAL TESTING - PART 3-6: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE/HUMIDITY CHAMBERS
I.S. EN 11140-4:2007 STERILIZATION OF HEALTH CARE PRODUCTS - CHEMICAL INDICATORS - PART 4: CLASS 2 INDICATORS AS AN ALTERNATIVE TO THE BOWIE AND DICK-TYPE TEST FOR DETECTION OF STEAM PENETRATION
99/124125 DC : DRAFT NOV 1999 BS EN ISO 15883-1 - WASHER-DISINFECTORS - PART 1: GENERAL REQUIREMENTS, DEFINITIONS AND TESTS
BS EN 16242:2012 Conservation of cultural heritage. Procedures and instruments for measuring humidity in the air and moisture exchanges between air and cultural property
02/121895 DC : DRAFT APR 2002 BS EN 13060 - SMALL STEAM STERILIZERS
14/30291759 DC : 0 BS EN 1434-5 - HEAT METERS - PART 5: INITIAL VERIFICATION TESTS
PREN 17175 : DRAFT 2017 GAS-FIRED OVERHEAD RADIANT STRIP HEATERS AND MULTI-BURNER CONTINUOUS RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
17/30309582 DC : 0 BS EN 60350-2 ED 2.0 - HOUSEHOLD ELECTRIC COOKING APPLIANCES - PART 2: HOBS - METHODS FOR MEASURING PERFORMANCE
DIN EN ISO 18472:2006-10 STERILIZATION OF HEALTH CARE PRODUCTS - BIOLOGICAL AND CHEMICAL INDICATORS - TEST EQUIPMENT
DIN EN ISO 15970:2014-09 NATURAL GAS - MEASUREMENT OF PROPERTIES - VOLUMETRIC PROPERTIES: DENSITY, PRESSURE, TEMPERATURE AND COMPRESSION FACTOR (ISO 15970:2008)
06/30160085 DC : 0 BS ISO 15970 - NATURAL GAS - MEASUREMENT OF PROPERTIES - VOLUMETRIC PROPERTIES: DENSITY, PRESSURE, TEMPERATURE AND COMPRESSION FACTOR
BS EN 60534-2-3:2016 Industrial-process control valves Flow capacity. Test procedures
BS ISO 17714:2007 Meteorology. Air temperature measurements. Test methods for comparing the performance of thermometer shields/screens and defining important characteristics
AAMI ISO 11140-5 : 2007 STERILIZATION OF HEALTH CARE PRODUCTS - CHEMICAL INDICATORS - PART 5: CLASS 2 INDICATORS FOR BOWIE AND DICK-TYPE AIR REMOVAL TESTS
PREN 12599 : DRAFT 2010 VENTILATION FOR BUILDINGS - TEST PROCEDURES AND MEASUREMENT METHODS TO HAND OVER AIR CONDITIONING AND VENTILATION SYSTEMS
17/30363956 DC : 0 BS EN 419 - GAS-FIRED OVERHEAD LUMINOUS RADIANT HEATERS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
ASTM E 3137/E3137M : 2017 Standard Specification for Heat Meter Instrumentation
AAMI ISO 11140-4 : 2007 : R2012 STERILIZATION OF HEALTH CARE PRODUCTS - CHEMICAL INDICATORS - PART 4: CLASS 2 INDICATORS AS AN ALTERNATIVE TO THE BOWIE AND DICK-TYPE TEST FOR DETECTION OF STEAM PENETRATION
NF EN 16442 : 2015 CONTROLLED ENVIRONMENT STORAGE CABINET FOR PROCESSED THERMOLABILE ENDOSCOPES
UNE-EN 12405-3:2016 Gas meters - Conversion devices - Part 3: Flow computer
ISO 14661:2000 Thermal turbines for industrial applications (steam turbines, gas expansion turbines) General requirements
OIML R 84 : 2003 PLATINUM, COPPER, AND NICKEL RESISTANCE THERMOMETERS (FOR INDUSTRIAL AND COMMERCIAL USE)
I.S. EN ISO 2592:2017 PETROLEUM AND RELATED PRODUCTS - DETERMINATION OF FLASH AND FIRE POINTS - CLEVELAND OPEN CUP METHOD (ISO 2592:2017)
BS EN 12405-1 : 2005 GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION
BS EN 1434-2 : 2015 HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
I.S. EN 60068-3-5:2002 ENVIRONMENTAL TESTING - PART 3-5: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE CHAMBERS
BS EN ISO 18472:2006 Sterilization of health care products. Biological and chemical indicators. Test equipment and methods
EN ISO 18472:2006 Sterilization of health care products - Biological and chemical indicators - Test equipment (ISO 18472:2006)
I.S. EN 60068-3-7:2002 ENVIRONMENTAL TESTING - PART 3-7: SUPPORTING DOCUMENTATION AND GUIDANCE - MEASUREMENTS IN TEMPERATURE CHAMBERS FOR TESTS A AND B (WITH LOAD)
I.S. EN IEC 60068-3-5:2018 ENVIRONMENTAL TESTING - PART 3-5: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE CHAMBERS
I.S. EN 1434-1:2015 HEAT METERS - PART 1: GENERAL REQUIREMENTS
EN 1434-2:2015 Heat meters - Part 2: Constructional requirements
EN IEC 60068-3-6:2018/AC:2018-05 ENVIRONMENTAL TESTING - PART 3-6: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE/HUMIDITY CHAMBERS (IEC 60068-3-6:2018)
UNE-EN 1434-4:2016 Heat meters - Part 4: Pattern approval tests
AAMI ST15883-1 : 2009 : INC : AMD 1 : 2014 : R201400 WASHER-DISINFECTORS - PART 1: GENERAL REQUIREMENTS, TERMS AND DEFINITIONS AND TESTS
OIML R 75-2 : 2002 HEAT METERS - PART 2: TYPE APPROVAL TESTS AND INITIAL VERIFICATION TESTS
IEC 60068-3-5 REDLINE : 2.0 ENVIRONMENTAL TESTING - PART 3-5: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE CHAMBERS
BS 2000-34(2016) : 2016 DETERMINATION OF FLASH POINT - PENSKY-MARTENS CLOSED CUP METHOD (ISO 2719:2016)
EN ISO 2592:2017 Petroleum and related products - Determination of flash and fire points - Cleveland open cup method (ISO 2592:2017)
PREN 17066-1 : DRAFT 2016 INSULATED MEANS OF TRANSPORT FOR TEMPERATURE SENSITIVE GOODS - REQUIREMENTS AND TESTING - PART 1: CONTAINER
IEC 60737:2010 Nuclear power plants - Instrumentation important to safety - Temperature sensors (in-core and primary coolant circuit) - Characteristics and test methods
UNE-EN 1434-2:2016 Heat meters - Part 2: Constructional requirements
IEC PAS 61987-1:2002 Industrial-process measurement and control - Data structures and elements in process equipment catalogues - Part 1: Measuring equipment with analogue and digital output
I.S. EN 60947-8:2003 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 8: CONTROL UNITS FOR BUILT-IN THERMAL PROTECTION (PTC) FOR ROTATING ELECTRICAL MACHINES (IEC 60947-8:2003 (EQV))
DIN EN 15758 E : 2010 CONSERVATION OF CULTURAL PROPERTY - PROCEDURES AND INSTRUMENTS FOR MEASURING TEMPERATURES OF THE AIR AND THE SURFACES OF OBJECTS
DIN EN 16242:2013-03 CONSERVATION OF CULTURAL HERITAGE - PROCEDURES AND INSTRUMENTS FOR MEASURING HUMIDITY IN THE AIR AND MOISTURE EXCHANGES BETWEEN AIR AND CULTURAL PROPERTY
DIN EN 14597:2015-02 TEMPERATURE CONTROL DEVICES AND TEMPERATURE LIMITERS FOR HEAT GENERATING SYSTEMS
DIN EN 15758:2010-12 Conservation of Cultural Property - Procedures and instruments for measuring temperatures of the air and of the surfaces of objects
BS EN 12599:2012 Ventilation for buildings. Test procedures and measurement methods to hand over air conditioning and ventilation systems
DIN EN 1434-4:2019-08 Thermal energy meters - Part 4: Pattern approval tests (includes Amendment A1:2018)
I.S. EN 14597:2012 TEMPERATURE CONTROL DEVICES AND TEMPERATURE LIMITERS FOR HEAT GENERATING SYSTEMS
I.S. EN 16242:2012 CONSERVATION OF CULTURAL HERITAGE - PROCEDURES AND INSTRUMENTS FOR MEASURING HUMIDITY IN THE AIR AND MOISTURE EXCHANGES BETWEEN AIR AND CULTURAL PROPERTY
I.S. EN 12599:2012 VENTILATION FOR BUILDINGS - TEST PROCEDURES AND MEASUREMENT METHODS TO HAND OVER AIR CONDITIONING AND VENTILATION SYSTEMS
I.S. EN ISO 4892-1:2016 PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE (ISO 4892-1:2016)
DIN EN 14180:2003-10 STERILIZERS FOR MEDICAL PURPOSES - LOW TEMPERATURE STEAM AND FORMALDEHYDE STERILIZERS - REQUIREMENTS AND TESTING
I.S. EN 14180:2014 STERILIZERS FOR MEDICAL PURPOSES - LOW TEMPERATURE STEAM AND FORMALDEHYDE STERILIZERS - REQUIREMENTS AND TESTING
I.S. EN ISO 2719:2016 DETERMINATION OF FLASH POINT - PENSKY-MARTENS CLOSED CUP METHOD (ISO 2719:2016)
I.S. EN ISO 3679:2015 DETERMINATION OF FLASH NO-FLASH AND FLASH POINT - RAPID EQUILIBRIUM CLOSED CUP METHOD (ISO 3679:2015)
DIN EN ISO 4625-1:2006-04 BINDERS FOR PAINTS AND VARNISHES - DETERMINATION OF SOFTENING POINT - PART 1: RING-AND-BALL METHOD
VDI 3786 Blatt 3:2012-10 Environmental meteorology - Meteorologial measurements - Air temperature
VDI/VDE 3512 Blatt 2:2017-03 Temperature measurement for building automation - Temperature sensors, temperature sensing elements and their measurement parameters
VDI 3786 Blatt 4:2013-06 Environmental meteorology - Meteorological measurements - Air humidity
VDI/VDE 3512 Blatt 4:2017-03 Temperature measurement for building automation - Testing of temperature sensors
OIML R 140 : 2007 MEASURING SYSTEMS FOR GASEOUS FUEL
BS EN 60350-2 : 2013 HOUSEHOLD ELECTRIC COOKING APPLIANCES - HOBS - METHODS FOR MEASURING PERFORMANCE
CEI EN 60068-3-5 : 2002 ENVIRONMENTAL TESTING - PART 3-5: SUPPORTING DOCUMENTATION AND GUIDANCE CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE CHAMBERS
I.S. EN 285:2015 STERILIZATION - STEAM STERILIZERS - LARGE STERILIZERS
API MPM CH7.3 : 2011(R2016) MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 7.3: TEMPERATURE DETERMINATION - FIXED AUTOMATIC TANK TEMPERATURE SYSTEMS
DIN EN ISO 15970 E : 2014 NATURAL GAS - MEASUREMENT OF PROPERTIES - VOLUMETRIC PROPERTIES: DENSITY, PRESSURE, TEMPERATURE AND COMPRESSION FACTOR (ISO 15970:2008)
BS ISO 19291:2016 Lubricants. Determination of tribological quantities for oils and greases. Tribological test in the translatory oscillation apparatus
BS IEC 60737:2010 Nuclear power plants. Instrumentation important to safety Temperature sensors (in-core and primary coolant circuit). Characteristics and test methods
ISO 8310:2012 Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels — General requirements for automatic tank thermometers on board marine carriers and floating storage
CEI EN 60068-3-6 : 2002 ENVIRONMENTAL TESTING - PART 3-6: SUPPORTING DOCUMENTATION AND GUIDANCE CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE/HUMIDITY CHAMBERS
I.S. CEN TR 15177:2006 TESTING THE FREEZE-THAW RESISTANCE OF CONCRETE - INTERNAL STRUCTURAL DAMAGE
BS ISO 19618:2017 Fine ceramics (advanced ceramics, advanced technical ceramics). Measurement method for normal spectral emissivity using blackbody reference with an FTIR spectrometer
I.S. EN IEC 60068-3-6:2018 COR 2018 ENVIRONMENTAL TESTING - PART 3-6: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE/HUMIDITY CHAMBERS (IEC 60068-3-6:2018)
02/103093 DC : DRAFT APR 2002 BS 12390-9 - TESTING HARDENED CONCRETE - PART 9: FREEZE-THAW RESISTANCE - SCALING
BS EN ISO 15970:2014 Natural gas. Measurement of properties. Volumetric properties: density, pressure, temperature and compression factor
EN IEC 60068-3-5:2018 Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers
DIN EN 16442 E : 2015 CONTROLLED ENVIRONMENT STORAGE CABINET FOR PROCESSED THERMOLABILE ENDOSCOPES
NF ISO 14661 : 2000 AMD 1 2004 THERMAL TURBINES FOR INDUSTRIAL APPLICATIONS (STEAM TURBINES, GAS EXPANSION TURBINES) - GENERAL REQUIREMENTS
BS 2000-523(2015) : 2015 DETERMINATION OF FLASH NO-FLASH AND FLASH POINT - RAPID EQUILIBRIUM CLOSED CUP METHOD
13/30278676 DC : 0 BS EN 285 - STERILIZATION - STEAM STERILIZERS - LARGE STERILIZERS
15/30301302 DC : 0 BS EN ISO 2719 - DETERMINATION OF FLASH POINT - PENSKY-MARTENS CLOSED CUP METHOD
07/30170559 DC : DRAFT AUG 2007 BS ISO 2314 - GAS TURBINES - ACCEPTANCE TESTS
04/30124466 DC : DRAFT OCT 2004 EN 12405-1 - GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION
10/30235574 DC : 0 BS EN 12599 - VENTILATION FOR BUILDINGS - TEST PROCEDURES AND MEASUREMENT METHODS TO HAND OVER AIR CONDITIONING AND VENTILATION SYSTEMS
BS ISO 14661:2000 Thermal turbines for industrial applications (steam turbines, gas expansion turbines). General requirements
BS ISO 11140-5:2007 Sterilization of health care products. Chemical indicators Class 2 indicators for Bowie and Dick-type air removal tests
AAMI ISO 11140-5 : 2007 : R2012 STERILIZATION OF HEALTH CARE PRODUCTS - CHEMICAL INDICATORS - PART 5: CLASS 2 INDICATORS FOR BOWIE AND DICK-TYPE AIR REMOVAL TESTS
BS ISO 15970 : 2008 NATURAL GAS - MEASUREMENT OF PROPERTIES - VOLUMETRIC PROPERTIES: DENSITY, PRESSURE, TEMPERATURE AND COMPRESSION FACTOR
BS EN 60068-3-5:2002 Environmental testing. Guidance Confirmation of the performance of temperature chambers
IEC 60068-3-5:2018 Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers
API MPM CH7.3:2011 MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 7.3: TEMPERATURE DETERMINATION - FIXED AUTOMATIC TANK TEMPERATURE SYSTEMS
I.S. EN 12405-3:2015 GAS METERS - CONVERSION DEVICES - PART 3: FLOW COMPUTER
EN 13060:2014 Small steam sterilizers
I.S. EN 12405-1:2005 GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION
I.S. EN 1434-5:2015 HEAT METERS - PART 5: INITIAL VERIFICATION TESTS
PREN 1434-4 : DRAFT 2014 HEAT METERS - PART 4: PATTERN APPROVAL TESTS
AAMI ST15883-1 : 2009 WASHER-DISINFECTORS - PART 1: GENERAL REQUIREMENTS, TERMS AND DEFINITIONS AND TESTS
NF EN 60068-3-5 : 2002 ENVIRONMENTAL TESTING - PART 3-5: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE CHAMBERS
ANSI/AAMI ST15883-1:2009(R2014) &A1:2014&A2:2012 WASHER-DISINFECTORS - PART 1: GENERAL REQUIREMENTS, TERMS AND DEFINITIONS AND TESTS
DIN EN 1434-2:2016-02 HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
I.S. EN 16442:2015 CONTROLLED ENVIRONMENT STORAGE CABINET FOR PROCESSED THERMOLABILE ENDOSCOPES
ISO 11140-5:2007 Sterilization of health care products — Chemical indicators — Part 5: Class 2 indicators for Bowie and Dick-type air removal tests
API 551 : 2016 PROCESS MEASUREMENT
DIN EN 13060:2015-03 SMALL STEAM STERILIZERS
DIN EN ISO 3679:2015-06 Determination of flash no-flash and flash point - Rapid equilibrium closed cup method (ISO 3679:2015)
DIN EN 12259-1:2006-03 Fixed firefighting systems - Components for sprinkler and water spray systems - Part 1: Sprinklers
DIN EN 14705 E : 2005 HEAT EXCHANGERS - METHOD OF MEASUREMENT AND EVALUATION OF THERMAL PERFORMANCES OF WET COOLING TOWERS
DIN EN 285:2016-05 Sterilization - Steam sterilizers - Large sterilizers
BS EN 1434-5:2015 Heat meters Initial verification tests
ISO 15883-1:2006 Washer-disinfectors Part 1: General requirements, terms and definitions and tests
IEC 60068-3-7:2001 Environmental testing - Part 3-7: Supporting documentation and guidance - Measurements in temperature chambers for tests A and B (with load)
EN 60068-3-7:2002 Environmental testing - Part 3-7: Supporting documentation and guidance - Measurements in temperature chambers for tests A and B (with load)
I.S. EN ISO 4625-1:2006 BINDERS FOR PAINTS AND VARNISHES - DETERMINATION OF SOFTENING POINT - PART 1: RING-AND-BALL METHOD
EN ISO 4625-1:2006 Binders for paints and varnishes - Determination of softening point - Part 1: Ring-and-ball method (ISO 4625-1:2004)
ONORM EN ISO 4625-1 : 2006 BINDERS FOR PAINTS AND VARNISHES - DETERMINATION OF SOFTENING POINT - PART 1: RING-AND-BALL METHOD
I.S. EN ISO 15883-1:2009 WASHER-DISINFECTORS - PART 1: GENERAL REQUIREMENTS, TERMS AND DEFINITIONS AND TESTS (ISO 15883-1:2006)
UNI EN 12599 : 2012 VENTILATION FOR BUILDINGS - TEST PROCEDURES AND MEASUREMENT METHODS TO HAND OVER AIR CONDITIONING AND VENTILATION SYSTEMS
UNI EN ISO 15883-1 : 2014 WASHER-DISINFECTORS - PART 1: GENERAL REQUIREMENTS, TERMS AND DEFINITIONS AND TESTS
UNI EN 14597 : 2012 TEMPERATURE CONTROL DEVICES AND TEMPERATURE LIMITERS FOR HEAT GENERATING SYSTEMS
UNI EN 14180 : 2014 STERILIZERS FOR MEDICAL PURPOSES - LOW TEMPERATURE STEAM AND FORMALDEHYDE STERILIZERS - REQUIREMENTS AND TESTING
UNI EN 16242 : 2013 CONSERVATION OF CULTURAL HERITAGE - PROCEDURES AND INSTRUMENTS FOR MEASURING HUMIDITY IN THE AIR AND MOISTURE EXCHANGES BETWEEN AIR AND CULTURAL PROPERTY
API MPM CH7.3 SPANISH : 2011 MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 7.3: TEMPERATURE DETERMINATION - FIXED AUTOMATIC TANK TEMPERATURE SYSTEMS
12/30244792 DC : 0 BS ISO 8310 - REFRIGERATED HYDROCARBON AND NON-PETROLEUM BASED LIQUEFIED GASEOUS FUELS - GENERAL REQUIREMENTS FOR AUTOMATIC TANK THERMOMETERS ON BOARD MARINE CARRIERS AND FLOATING STORAGE
BS EN 1434-4 : 2015 HEAT METERS - PART 4: PATTERN APPROVAL TESTS
08/30173520 DC : DRAFT FEB 2008 BS EN 15758 - CONSERVATION OF CULTURAL PROPERTY - PROCEDURES AND INSTRUMENTS FOR MEASURING TEMPERATURES OF THE AIR AND THE SURFACES OF OBJECTS
DIN EN 12405-3:2016-04 Gas meters - Conversion devices - Part 3: Flow computer
PD CEN/TS 12390-9:2016 Testing hardened concrete Freeze-thaw resistance with de-icing salts. Scaling
PREN 17180 : DRAFT 2017 STERILIZERS FOR MEDICAL PURPOSES - LOW TEMPERATURE VAPORIZED HYDROGEN PEROXIDE STERILIZERS - REQUIREMENTS AND TESTING
BS EN 16442:2015 Controlled environment storage cabinet for processed thermolabile endoscopes
CAN/CSA-ISO 11140-4:18 CAN/CSA-ISO 11140-4:18 - Sterilization of health care products — Chemical indicators — Part 4: Class 2 indicators as an alternative to the Bowie and Dick-type test for detection of steam penetration (Adopted ISO 11140-4:2007, second edition, 2007-03-15)
CSA C900.2 : 2013 HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
BS EN 12405-3:2015 Gas meters. Conversion devices Flow computer
16/30330536 DC : 0 BS EN ISO 18472 - STERILIZATION OF HEALTH CARE PRODUCTS - BIOLOGICAL AND CHEMICAL INDICATORS - TEST EQUIPMENT
PREN 1434-2 : DRAFT 2014 HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
DIN 43735:2011-06 PROCESS CONTROL TECHNOLOGY - ELECTRICAL TEMPERATURE SENSORS - REPLACEABLE INSERTS FOR RTDS AND THERMOCOUPLES
BS EN 60947-8:2003 Low-voltage switchgear and controlgear Control units for built-in thermal protection (PTC) for rotating electrical machines
04/30112930 DC : DRAFT APR 2004 IEC 61987-1 ED.1 - INDUSTRIAL PROCESS MEASUREMENT AND CONTROL - DATA STRUCTURES AND ELEMENTS IN PROCESS EQUIPMENT CATALOGUES - PART 1: MEASURING EQUIPMENT WITH ANALOGUE AND DIGITAL OUTPUT
16/30325304 DC : 0 BS EN ISO 2592 - PETROLEUM AND RELATED PRODUCTS - DETERMINATION OF FLASH AND FIRE POINTS - CLEVELAND OPEN CUP METHOD
14/30295943 DC : 0 BS ISO 6487 - ROAD VEHICLES - MEASUREMENT TECHNIQUES IN IMPACT TESTS - INSTRUMENTATION
14/30312597 DC : 0 BS EN 62828-3 ED.1 IEC 62828-3 ED.1 - REFERENCE CONDITIONS AND PROCEDURES FOR TESTING INDUSTRIAL MEASUREMENT TRANSMITTERS - PART 3: SPECIFIC PROCEDURES FOR TEMPERATURE TRANSMITTERS
PREN 419 : DRAFT 2017 GAS-FIRED OVERHEAD LUMINOUS RADIANT HEATERS FOR NONDOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
BS ISO 2314:2009 Gas turbines. Acceptance tests
UNE-EN ISO 15970:2014 Natural gas - Measurement of properties - Volumetric properties: density, pressure, temperature and compression factor (ISO 15970:2008)
EN 1434-4:2015 Heat meters - Part 4: Pattern approval tests
10/30219217 DC : 0 BS ISO 6487 - ROAD VEHICLES - MEASUREMENT TECHNIQUES IN IMPACT TESTS - INSTRUMENTATION
DIN EN 12405-3 E : 2016 GAS METERS - CONVERSION DEVICES - PART 3: FLOW COMPUTER
13/30285144 DC : 0 BS ISO 3679 - DETERMINATION OF FLASH POINT - RAPID EQUILIBRIUM CLOSED CUP METHOD
BS EN 61987-1:2007 Industrial-process measurement and control. Data structures and elements in process equipment catalogues Measuring equipment with analogue and digital output
DIN EN 1434-4:2016-02 HEAT METERS - PART 4: PATTERN APPROVAL TESTS
09/30165791 DC : 0 BS IEC 60737 - NUCLEAR POWER PLANT - INSTRUMENTATION IMPORTANT TO SAFETY - TEMPERATURE SENSORS (INCORE AND PRIMARY COOLANT CIRCUIT): CHARACTERISTICS AND TEST METHODS
BS ISO 6487 : 2015 ROAD VEHICLES - MEASUREMENT TECHNIQUES IN IMPACT TESTS - INSTRUMENTATION
DIN EN 16442:2015-05 CONTROLLED ENVIRONMENT STORAGE CABINET FOR PROCESSED THERMOLABILE ENDOSCOPES
UNI EN 12405-1 : 2010 GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION
15/30330287 DC : DRAFT AUG 2015 BS EN 60068-3-5 - ENVIRONMENTAL TESTING - PART 3-5: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE CHAMBERS
I.S. EN 60068-3-6:2002 ENVIRONMENTAL TESTING - PART 3-6: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE/HUMIDITY CHAMBERS
UNE-EN 16442:2015 Controlled environment storage cabinet for processed thermolabile endoscopes
S.R. CEN/TS 12390-9:2016 TESTING HARDENED CONCRETE - PART 9: FREEZE-THAW RESISTANCE WITH DE-ICING SALTS - SCALING
ISO 13737:2004 Petroleum products and lubricants Determination of low-temperature cone penetration of lubricating greases
16/30348307 DC : 0 BS EN 17066-1 - INSULATED MEANS OF TRANSPORT FOR TEMPERATURE SENSITIVE GOODS - REQUIREMENTS AND TESTING - PART 1: CONTAINER
17/30363959 DC : 0 BS EN 17175 - GAS-FIRED OVERHEAD RADIANT STRIP HEATERS AND MULTI-BURNER CONTINUOUS RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY
DIN EN 1434-5:2016-02 HEAT METERS - PART 5: INITIAL VERIFICATION TESTS
IEC 60068-3-6 REDLINE : 2.0 ENVIRONMENTAL TESTING - PART 3-6: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE/HUMIDITY CHAMBERS
DIN EN 1434-1:2016-02 HEAT METERS - PART 1: GENERAL REQUIREMENTS
UNE-EN 13060:2015 Small steam sterilizers
ISO/TR 9464:2008 Guidelines for the use of ISO 5167:2003
ISO 18472:2006 Sterilization of health care products Biological and chemical indicators Test equipment
EN 12405-1:2005+A2:2010 Gas meters - Conversion devices - Part 1: Volume conversion
I.S. EN ISO 18472:2006 STERILIZATION OF HEALTH CARE PRODUCTS - BIOLOGICAL AND CHEMICAL INDICATORS - TEST EQUIPMENT
IEC 60068-3-6:2018 Environmental testing - Part 3-6: Supporting documentation and guidance - Confirmation of the performance of temperature/ humidity chambers
I.S. CEN TS 12390-9:2006 TESTING HARDENED CONCRETE - PART 9: FREEZE-THAW RESISTANCE - SCALING
UNE-EN 1434-1:2016 Heat meters - Part 1: General requirements
UNE-EN ISO 15883-1:2009 Washer-disinfectors - Part 1: General requirements, terms and definitions and tests (ISO 15883-1:2006)
DIN EN 12599:2013-01 VENTILATION FOR BUILDINGS - TEST PROCEDURES AND MEASUREMENT METHODS TO HAND OVER AIR CONDITIONING AND VENTILATION SYSTEMS
DIN EN 14597 E : 2015 TEMPERATURE CONTROL DEVICES AND TEMPERATURE LIMITERS FOR HEAT GENERATING SYSTEMS
DIN EN 14180:2014-09 STERILIZERS FOR MEDICAL PURPOSES - LOW TEMPERATURE STEAM AND FORMALDEHYDE STERILIZERS - REQUIREMENTS AND TESTING
DIN EN ISO 4892-1:2016-10 PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE (ISO 4892-1:2016)
ISO 3679:2015 Determination of flash no-flash and flash point — Rapid equilibrium closed cup method
ISO 4892-1:2016 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
BS EN ISO 11140-4:2007 Sterilization of health care products. Chemical indicators Class 2 indicators as an alternative to the Bowie and Dick-type test for detection of steam penetration
IEC 61987-1:2006 Industrial-process measurement and control - Data structures and elements in process equipment catalogues - Part 1: Measuring equipment with analogue and digital output
IEC 60947-8:2003+AMD1:2006+AMD2:2011 CSV Low-voltage switchgear and controlgear - Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines
BS EN ISO 2719:2002 Determination of flash point. Pensky-Martens closed cup method
BS EN ISO 3679:2015 Determination of flash no-flash and flash point. Rapid equilibrium closed cup method
UNE-EN ISO 3679:2015 Determination of flash no-flash and flash point - Rapid equilibrium closed cup method (ISO 3679:2015)
BS EN 867-4:2001 Non-biological systems for use in sterilizers Specification for indicators as an alternative to the Bowie and Dick test for the detection of steam penetration
BS EN ISO 4892-1:2016 Plastics. Methods of exposure to laboratory light sources General guidance
ISO 11140-4:2007 Sterilization of health care products — Chemical indicators — Part 4: Class 2 indicators as an alternative to the Bowie and Dick-type test for detection of steam penetration
BS EN 13060 : 2014 SMALL STEAM STERILIZERS
BS EN 285:2015 Sterilization. Steam sterilizers. Large sterilizers
BS EN 14705:2005 Heat exchangers. Method of measurement and evaluation of thermal performances of wet cooling towers
UNE-EN 16242:2014 Conservation of cultural heritage - Procedures and instruments for measuring humidity in the air and moisture exchanges between air and cultural property
ISO 4625-1:2004 Binders for paints and varnishes Determination of softening point Part 1: Ring-and-ball method
BS EN 14180:2014 Sterilizers for medical purposes. Low temperature steam and formaldehyde sterilizers. Requirements and testing
ISO 6182-9:2005 Fire protection — Automatic sprinkler system — Part 9: Requirements and test methods for water mist nozzles
DIN EN 12952-15:2004-01 Water tube boilers and auxiliary installations - Part 15: Acceptance tests; German version EN 12952-15:2003
BS EN 14597:2012 Temperature control devices and temperature limiters for heat generating systems
UNE-EN ISO 2719:2017 Determination of flash point - Pensky-Martens closed cup method (ISO 2719:2016)
ISO 6182-10:2014 Fire protection — Automatic sprinkler systems — Part 10: Requirements and test methods for domestic sprinklers
BS EN ISO 15883-1 : 2009 WASHER-DISINFECTORS - PART 1: GENERAL REQUIREMENTS, TERMS AND DEFINITIONS AND TESTS (ISO 15883-1:2006)
BS EN 15758:2010 Conservation of cultural property. Procedures and instruments for measuring temperatures of the air and the surfaces of objects
UNE-EN 15758:2011 Conservation of Cultural Property - Procedures and instruments for measuring temperatures of the air and the surfaces of objects
ISO 2719:2016 Determination of flash point Pensky-Martens closed cup method
UNE-EN ISO 4892-1:2017 Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016)
ISO 15970:2008 Natural gas Measurement of properties Volumetric properties: density, pressure, temperature and compression factor
EN ISO 4892-1:2016 Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016)
EN ISO 15970:2014 Natural gas - Measurement of properties - Volumetric properties: density, pressure, temperature and compression factor (ISO 15970:2008)
EN ISO 11140-4:2007 Sterilization of health care products - Chemical indicators - Part 4: Class 2 indicators as an alternative to the Bowie and Dick-type test for detection of steam penetration (ISO 11140-4:2007)
EN 14597:2012 Temperature control devices and temperature limiters for heat generating systems
EN ISO 3679:2015 Determination of flash no-flash and flash point - Rapid equilibrium closed cup method (ISO 3679:2015)
EN 16242:2012 Conservation of cultural heritage - Procedures and instruments for measuring humidity in the air and moisture exchanges between air and cultural property
EN 14705:2005 Heat exchangers - Method of measurement and evaluation of thermal performances of wet cooling towers
EN 15758:2010 Conservation of Cultural Property - Procedures and instruments for measuring temperatures of the air and the surfaces of objects
EN 14180:2014 Sterilizers for medical purposes - Low temperature steam and formaldehyde sterilizers - Requirements and testing
EN 16442:2015 Controlled environment storage cabinet for processed thermolabile endoscopes
BS ISO 8310:2012 Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels. General requirements for automatic tank thermometers on board marine carriers and floating storage
PREN 1434-5 : DRAFT 2014 HEAT METERS - PART 5: INITIAL VERIFICATION TESTS
DIN ISO 17714:2008-06 METEOROLOGY - AIR TEMPERATURE MEASUREMENTS - TEST METHODS FOR COMPARING THE PERFORMANCE OF THERMOMETER SHIELDS/SCREENS AND DEFINING IMPORTANT CHARACTERISTICS
ISO 18888:2017 Gas turbine combined cycle power plants — Thermal performance tests
DKD-R 5-6 : 2008
BS 2000-527(2004) : 2004 METHOD OF TEST FOR PETROLEUM AND ITS PRODUCTS - BS 2000-527: PETROLEUM PRODUCTS AND LUBRICANTS - DETERMINATION OF LOW-TEMPERATURE CONE PENETRATION OF LUBRICATING GREASES
I.S. EN 13060:2014 SMALL STEAM STERILIZERS
06/30151216 DC : DRAFT JUN 2006
07/30127284 DC : 0 BS EN ISO 4892-1 - PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE
DD CEN/TS 12390-9:2006 Testing hardened concrete Freeze-thaw resistance. Scaling
BS ISO 18888:2017 Gas turbine combined cycle power plants. Thermal performance tests
CSA C900.4 : 2013 HEAT METERS - PART 4: PATTERN APPROVAL TESTS
ISO 2314:2009 Gas turbines — Acceptance tests
API MPM CH7.5 : 2014 MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 7.5: TEMPERATURE DETERMINATION - AUTOMATIC TANK TEMPERATURE MEASUREMENT ONBOARD MARINE VESSELS CARRYING REFRIGERATED HYDROCARBON AND CHEMICAL GAS FLUIDS
UNI EN 15758 : 2010 CONSERVATION OF CULTURAL PROPERTY - PROCEDURES AND INSTRUMENTS FOR MEASURING TEMPERATURES OF THE AIR AND THE SURFACES OF OBJECTS
UNI EN ISO 15970 : 2014 NATURAL GAS - MEASUREMENT OF PROPERTIES - VOLUMETRIC PROPERTIES: DENSITY, PRESSURE, TEMPERATURE AND COMPRESSION FACTOR
CSA C900.1 : 2013 HEAT METERS - PART 1: GENERAL REQUIREMENTS
I.S. EN 60534-2-3:2016 INDUSTRIAL-PROCESS CONTROL VALVES - PART 2-3: FLOW CAPACITY TEST PROCEDURES
ISO 19618:2017 Fine ceramics (advanced ceramics, advanced technical ceramics) — Measurement method for normal spectral emissivity using blackbody reference with an FTIR spectrometer
ISO 17714:2007 Meteorology Air temperature measurements Test methods for comparing the performance of thermometer shields/screens and defining important characteristics
EN 1434-1:2015 Heat meters - Part 1: General requirements
AAMI ISO 18472 : 2007 STERILIZATION OF HEALTH CARE PRODUCTS - BIOLOGICAL AND CHEMICAL INDICATORS - TEST EQUIPMENT
I.S. EN 60350-2:2018 HOUSEHOLD ELECTRIC COOKING APPLIANCES - PART 2: HOBS - METHODS FOR MEASURING PERFORMANCE
I.S. EN 1434-2:2015 HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
FD X07 029-1 : 2002 FD METROLOGY - CALIBRATION AND VERIFICATION PROCEDURE FOR THERMOMETERS - PART 1: CALIBRATION AND VERIFICATION PROCEDURE FOR PROBES AND RESISTANCE THERMOMETERS
CAN/CSA-ISO 11140-5:18 CAN/CSA-ISO 11140-5:18 - Sterilization of health care products — Chemical indicators — Part 5: Class 2 indicators for Bowie and Dick-type air removal tests (Adopted ISO 11140-5:2007, second edition, 2007-03-15)
EN 1434-5:2015 Heat meters - Part 5: Initial verification tests
UNE-EN 1434-5:2016 Heat meters - Part 5: Initial verification tests
ISO 6487:2015 Road vehicles — Measurement techniques in impact tests — Instrumentation
DIN EN ISO 15883-1:2014-10 WASHER-DISINFECTORS - PART 1: GENERAL REQUIREMENTS, TERMS AND DEFINITIONS AND TESTS (ISO 15883-1:2006 + AMD 1:2014)
DIN EN 12405-1:2011-04 GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION
UNE-EN 285:2016 Sterilization - Steam sterilizers - Large sterilizers
BS EN 12259-1:1999 Fixed firefighting systems. Components for sprinkler and water spray systems Sprinklers
BS EN 12953-11:2003 Shell boilers Acceptance tests
UNE-EN 14597:2014 Temperature control devices and temperature limiters for heat generating systems
EN ISO 15883-1:2009/A1:2014 WASHER-DISINFECTORS - PART 1: GENERAL REQUIREMENTS, TERMS AND DEFINITIONS AND TESTS (ISO 15883-1:2006/AMD 1:2014)
NF EN 60068-3-7 : 2002 ENVIRONMENTAL TESTING - PART 3-7: SUPPORTING DOCUMENTATION AND GUIDANCE - MEASUREMENTS IN TEMPERATURE CHAMBERS FOR TESTS A AND TEST B (WITH LOAD)
EN 12952-15:2003 Water-tube boilers and auxiliary installations - Part 15: Acceptance tests
EN 61987-1:2007 Industrial-process measurement and control - Data structures and elements in process equipment catalogues - Part 1: Measuring equipment with analogue and digital output
EN 60068-3-5:2002 Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers
EN 60534-2-3:2016 Industrial-process control valves - Part 2-3: Flow capacity - Test procedures
EN 12405-3 : 2015 GAS METERS - CONVERSION DEVICES - PART 3: FLOW COMPUTER
DIN EN ISO 4892-1:2001-09 PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE (ISO 4892-1:2016)
UNE-EN 60350-2:2014 Household electric cooking appliances - Part 2: Hobs - Methods for measuring performance

IEC 61298-1:2008 Process measurement and control devices - General methods and procedures for evaluating performance - Part 1: General considerations
IEC 61152:1992 Dimensions of metal-sheathed thermometer elements

View more information
US$174.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.