• There are no items in your cart

IEC TS 62081:1999

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Arc welding equipment - Installation and use
Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

01-21-2010

Language(s)

English - French, English, French

Published date

05-07-1999

Foreword
1 Scope
2 Normative references
3 Definitions
4 Installation
   4.1 General
        4.1.1 Selection of supply cable and protection
               against overload
        4.1.2 Supply disconnecting device
        4.1.3 Emergency stopping device
        4.1.4 Protection against electric shock from the
               mains supply
   4.2 Welding circuit
        4.2.1 Isolation from the mains supply
        4.2.2 Welding voltage supply
        4.2.3 Connection between the welding power source
               and the work piece
        4.2.4 Earthing of the work piece
        4.2.5 Location of gas cylinders
5 Use
   5.1 General requirements
   5.2 Connection between several welding power sources
   5.3 Inspection and maintenance of the welding
        installation
   5.4 Disconnection of welding power sources and/or
        welding circuits
   5.5 Guards
   5.6 Information for operators
   5.7 Protective measures
        5.7.1 Extraneous conductive parts in the welding
               area
        5.7.2 Protection against electric shock
   5.8 Isolation of the welding circuit from the work
        piece and earth when not in use
   5.9 Voltage between electrode holders or torches/guns
   5.10 Welding in an environment with increased hazard of
        electric shock
   5.11 Use of shoulder slings
   5.12 Welding at elevated positions
Annex A - Hazards connected with arc welding
Bibliography

This Technical Specification describes the general conditions for the installation and use of arc welding equipment that comply with IEC 60974-1. Gives particular information for operators.

DocumentType
Technical Specification
Pages
41
PublisherName
International Electrotechnical Committee
Status
Superseded
SupersededBy

Standards Relationship
CEI CLC/TS 62081 : 2003 Identical
CLC/TS 62081:2002 Identical
DD CLC/TS 62081:2002 Identical
NEN EN IEC 62081 : 2002 Identical

BS 7671(2008) : 2018 REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - IET WIRING REGULATIONS
EN 1011-1:2009 Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding
CEI EN 50504 : 2009 VALIDATION OF ARC WELDING EQUIPMENT
DIN EN 1011-1:2009-07 WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 1: GENERAL GUIDANCE FOR ARC WELDING
I.S. EN 1011-1:2009 WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 1: GENERAL GUIDANCE FOR ARC WELDING
NEMA IEC 60974-1 : 2008 ARC WELDING EQUIPMENT - PART 1: WELDING POWER SOURCES
08/30195564 DC : 0 BS EN 60974-1 - ARC WELDING EQUIPMENT - PART 1: WELDING POWER SOURCES
I.S. EN 50504:2008 VALIDATION OF ARC WELDING EQUIPMENT
UNI EN 1011-1 : 2009 WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 1: GENERAL GUIDANCE FOR ARC WELDING
06/30160338 DC : 0 BS EN 50504 - VALIDATION OF ARC WELDING EQUIPMENT
BS EN 1011-1:2009 Welding. Recommendations for welding of metallic materials General guidance for arc welding
BS EN 50504:2008 Validation of arc welding equipment
BS 7671(2008) : 2008 REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - IET WIRING REGULATIONS
EN 50504:2008 Validation of arc welding equipment

EN 60974-11:2010 ARC WELDING EQUIPMENT - PART 11: ELECTRODE HOLDERS
IEC 60974-5:2013 Arc welding equipment - Part 5: Wire feeders
IEC 60050-195:1998 International Electrotechnical Vocabulary (IEV) - Part 195: Earthing and protection against electric shock
HD 384.4.41 S2:1996/A1:2002 ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 4: PROTECTION FOR SAFETY - CHAPTER 41: PROTECTION AGAINST ELECTRIC SHOCK
IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
EN 60974-12:2011 Arc welding equipment - Part 12: Coupling devices for welding cables
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
IEC 60974-12:2011 Arc welding equipment - Part 12: Coupling devices for welding cables
IEC 60974-1:2017 Arc welding equipment - Part 1: Welding power sources
EN 61140:2016 Protection against electric shock - Common aspects for installation and equipment
IEC 60974-11:2010 Arc welding equipment - Part 11: Electrode holders
IEC 60947-2:2016 Low-voltage switchgear and controlgear - Part 2: Circuit-breakers
IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
EN 60947-2:2017 Low-voltage switchgear and controlgear - Part 2: Circuit-breakers
EN 60974-1:2012 Arc welding equipment - Part 1: Welding power sources
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

View more information
US$174.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.