• There are no items in your cart

ISO 1133-2:2011

Current
Current

The latest, up-to-date edition.

Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Language(s)

French, English

Published date

11-29-2011

Preview

ISO 1133-2:2011 specifies a procedure for the determination of the melt volume-flow rate (MVR) and melt mass-flow rate (MFR) of thermoplastic materials that exhibit a high rheological sensitivity to the time-temperature history experienced by the sample during the test and/or to moisture.

It is possible that this method will not be appropriate for materials whose rheological behaviour is extremely affected during testing.

MFR values can be determined by calculation from MVR measurements provided the melt density at the test temperature and pressure is known, or by measurement using a cutting device provided that the accuracy of the measurement is at least the same as that of the MVR measurement.

The primary difference between ISO 1133-2:2011 and ISO 1133-1 is that ISO 1133-2:2011 specifies tighter tolerances on the temperature in the cylinder and on the time duration over which the material is subjected to that temperature. Thus the time-temperature history of the material is more tightly controlled and consequently, for materials that are likely to be affected by exposure to elevated temperatures, the variability of test results is reduced compared with whether the specifications of ISO 1133-1 were used.

ISO 1133-2:2011 also provides information for preparation and handling of moisture sensitive materials that again are critical to obtaining repeatable, reproducible and accurate data.

The test conditions for measurement of the MVR and MFR are often specified in the material standard. However, for those materials where there are no test conditions specified in the material standard, it is necessary for the test conditions to be agreed between the interested parties

DevelopmentNote
Supersedes ISO/DIS 1133-2. (12/2011)
DocumentType
Standard
Pages
16
PublisherName
International Organization for Standardization
Status
Current

BS EN ISO 16396-2:2017 Plastics. Polyamide (PA) moulding and extrusion materials Preparation of test specimens and determination of properties
I.S. EN ISO 7792-2:2012 PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 7792-2:2012)
PREN 13491 : DRAFT 2016 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES
BS EN 16506:2014 Systems for renovation of drains and sewers. Lining with a rigidly anchored plastics inner layer (RAPL)
16/30338114 DC : 0 BS EN 13361 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS
16/30334902 DC : 0 BS EN ISO 10350-1 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS
BS ISO 7628:2010 Road vehicles. Thermoplastics tubing for air braking systems
DIN EN 16506:2014-12 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
BS ISO 11443:2014 Plastics. Determination of the fluidity of plastics using capillary and slit-die rheometers
NF EN ISO 1133-1 : 2012 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS - PART 1: STANDARD METHOD
15/30315534 DC : 0 BS EN ISO 16396-2 - PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
BS ISO 12418-2:2012 Plastics. Post-consumer poly(ethylene terephthalate) (PET) bottle recyclates Preparation of test specimens and determination of properties
DIN EN ISO 16396-2:2017-07 Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017)
BS EN ISO 10350-1:2017 Plastics. Acquisition and presentation of comparable single-point data Moulding materials
EN 13491:2018 Geosynthetic barriers - Characteristics required for use in the construction of tunnels and associated underground structures
ASTM D 5927 : 2017 : REDLINE Standard Classification System for and Basis for Specifications for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods
I.S. EN 12566-3:2016 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS
BS EN 14471 : 2013 CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS
I.S. EN ISO 11403-2:2012 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES (ISO 11403-2:2012)
EN 12566-3:2016 Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants
ONORM EN 1555-3 : 2013 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 3: FITTINGS
ONORM EN 1555-1 : 2015 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL
ONORM EN 12201-3 : 2013 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS
ONORM EN 12201-1 : 2015 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 1: GENERAL
ONORM EN 12201-2 : 2013 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 2: PIPES
VDI 3405 Blatt 1.1:2017-08 (Draft) Additive manufacturing processes - Laser sintering of polymer parts - Qualification of materials
ONORM B 5101 : 2013 SEPARATOR SYSTEMS FOR LIGHT LIQUIDS (E.G. OIL AND PETROL) - SUPPLEMENTARY REQUIREMENTS TO ONORM EN 858-1 AND -2
16/30338108 DC : DRAFT JULY 2016 BS EN 13362 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS
DIN EN ISO 1133-1:2012-03 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
DIN ISO 16486-2 E : 2015 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS WITH FUSION JOINTING AND MECHANICAL JOINTING - PART 2: PIPES (ISO 16486-2:2012 + AMD 1:2014)
16/30338105 DC : 0 BS EN 16994 - CLAY GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF UNDERGROUND STRUCTURES (OTHER THAN TUNNELS AND ASSOCIATED STRUCTURES)
17/30349217 DC : 0 BS EN ISO 21970-2 - PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
ISO 11443:2014 Plastics Determination of the fluidity of plastics using capillary and slit-die rheometers
ISO 20029-2:2017 Plastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 2: Preparation of test specimens and determination of properties
BS EN 16993:2018 Geosynthetic barriers. Characteristics required for use in the construction of storage lagoons, secondary containment (above and below ground) and other containment applications for chemicals, polluted water and produced liquids
PREN 15348 : DRAFT 2013 PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLY(ETHYLENE TEREPHTHALATE) (PET) RECYCLATES
UNE-EN ISO 20028-2:2017 Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 20028-2:2017)
PREN 13362 : DRAFT 2012 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF CANALS
DIN EN ISO 1874-2:2013-03 PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012)
DIN EN 14471:2015-03 CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS
BS EN ISO 1874-2:2012 Plastics. Polyamide (PA) moulding and extrusion materials Preparation of test specimens and determination of properties
I.S. EN 14471:2013 CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS
ONORM EN 13476-3 : 2015 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B (AMENDMENT)
ONORM EN 14758-1 : 2012 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIERS (PP-MD) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
I.S. EN ISO 1874-2:2012 PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012)
ONORM EN 13476-2 : 2015 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A (AMENDMENT)
NBR ISO 16486-2 : 2013 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS WITH FUSION JOINTING AND MECHANICAL JOINTING - PART 2: PIPES
VDI 3405 Blatt 1:2013-10 Additive manufacturing processes, rapid manufacturing - Laser sintering of polymer parts - Quality control
ONORM EN ISO 11403-2 : 2012 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES (ISO 11403-2:2012)
ONORM EN ISO 1133-1 : 2012 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS - PART 1: STANDARD METHOD (ISO 1133-1:2011)
16/30338117 DC : 0 BS EN 13493 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES
DIN EN ISO 19069-1 E : 2015 PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 19069-1:2015)
DIN ISO 16486-2:2015-07 Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 2: Pipes (ISO 16486-2:2012 + AMD 1:2014)
S.R. CEN/TS 14541:2013 PLASTICS PIPES AND FITTINGS - CHARACTERISTICS FOR UTILISATION OF NON-VIRGIN PVC-U, PP AND PE MATERIALS
I.S. EN 16993:2018 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF STORAGE LAGOONS, SECONDARY CONTAINMENT (ABOVE AND BELOW GROUND) AND OTHER CONTAINMENT APPLICATIONS FOR CHEMICALS, POLLUTED WATER AND PRODUCED LIQUIDS
PD CEN/TS 14541:2013 Plastics pipes and fittings. Characteristics for utilisation of non-virgin PVC-U, PP and PE materials
UNE-EN 15348:2015 Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates
UNI EN 16506 : 2014 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
13/30240167 DC : 0 BS ISO 16365-2 - PLASTICS - THERMOPLASTIC POLYURETHANES FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
BS EN 15348:2014 Plastics. Recycled plastics. Characterization of poly(ethylene terephthalate) (PET) recyclates
I.S. EN 13491:2018 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES
EN ISO 20029-2:2018 Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimen and determination of properties (ISO 20029-2:2017)
DIN EN 14471 E : 2015 CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS
ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
UNE-EN ISO 11403-2:2012 Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012)
BS EN ISO 11403-2:2012 Plastics. Acquisition and presentation of comparable multipoint data Thermal and processing properties
UNE-EN ISO 1874-2:2013 Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012)
EN 16506:2014 Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL)
UNI EN ISO 1874-2 : 2013 PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
UNI EN ISO 11403-2 : 2012 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES
UNI EN ISO 7792-2 : 2013 PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
UNI EN ISO 14910-2 : 2013 PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
ONORM EN 14427 : 2014 LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION
BS EN ISO 20029-2:2018 Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Preparation of test specimens and determination of properties
BS ISO 16365-2:2014 Plastics. Thermoplastic polyurethanes for moulding and extrusion Preparation of test specimens and determination of properties
UNI EN ISO 1133-1 : 2012 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS - PART 1: STANDARD METHOD
UNI CEN/TS 14541 : 2013 PLASTICS PIPES AND FITTINGS - CHARACTERISTICS FOR UTILISATION OF NON-VIRGIN PVC-U, PP AND PE MATERIALS
BS EN ISO 20028-2:2017 Plastics. Thermoplastic polyester (TP) moulding and extrusion materials Preparation of test specimens and determination of properties
BS EN ISO 1133-1:2011 Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
DIN EN 15348:2015-01 PLASTICS - RECYCLED PLASTICS - CHARACTERIZATION OF POLY(ETHYLENE TEREPHTHALATE) (PET) RECYCLATES
13/30283996 DC : 0 BS EN ISO 19069-1 - PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS
DIN EN ISO 20028-2 E : 2017 PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017)
PREN 13493 : DRAFT 2016 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF SOLID WASTE STORAGE AND DISPOSAL SITES
PREN 13492 : DRAFT 2016 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT
I.S. EN ISO 14910-2:2013 PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013, CORRECTED VERSION 2015-12-15)
DIN EN ISO 16396-2 E : 2017 PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 16396-2:2017)
15/30304408 DC : 0 BS EN ISO 20029-2 - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
BS EN 16994:2018 Clay Geosynthetic Barriers. Characteristics required for use in the construction of underground structures (other than tunnels and associated structures)
UNE-EN ISO 16396-2:2017 Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017)
I.S. EN 16994:2018 CLAY GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF UNDERGROUND STRUCTURES (OTHER THAN TUNNELS AND ASSOCIATED STRUCTURES)
I.S. EN ISO 20029-2:2018 PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES (ISO 20029-2:2017)
ISO 12418-2:2012 Plastics — Post-consumer poly(ethylene terephthalate) (PET) bottle recyclates — Part 2: Preparation of test specimens and determination of properties
DIN EN ISO 20028-2:2015-08 (Draft) PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017)
ISO 16365-2:2014 Plastics Thermoplastic polyurethanes for moulding and extrusion Part 2: Preparation of test specimens and determination of properties
EN 15382:2018 Geosynthetic barriers - Characteristics required for use in transportation infrastructure
ISO 7628:2010 Road vehicles Thermoplastics tubing for air braking systems
ISO 16486-2:2012 Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing Part 2: Pipes
I.S. EN 15382:2013 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE
UNE-EN ISO 14910-2:2014 Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013, Corrected version 2015-12-15)
UNE-EN ISO 7792-2:2013 Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7792-2:2012)
DIN EN ISO 14910-2 E : 2013 PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013)
ISO 20028-2:2017 Plastics — Thermoplastic polyester (TP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
UNE-EN 12566-3:2017 Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants
BS EN 12566-3 : 2005 SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS
ISO 1874-2:2012 Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO 11403-2:2012 Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties
ISO 7792-2:2012 Plastics Thermoplastic polyester (TP) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO 16396-2:2017 Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ONORM EN 253 : 2015 DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - PIPE ASSEMBLY OF STEEL SERVICE PIPE, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE
CEN/TS 14541:2013 Plastics pipes and fittings - Characteristics for utilisation of non-virgin PVC-U, PP and PE materials
EN ISO 11403-2:2012 Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012)
EN 14471:2013+A1:2015 CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS
EN ISO 1874-2:2012 Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012)
EN ISO 10350-1:2017 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)
EN ISO 16396-2:2017 Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017)
EN ISO 1133-1:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
EN ISO 20028-2:2017 Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 20028-2:2017)
EN 15348:2014 Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates
EN 16993:2018 Geosynthetic barriers - Characteristics required for use in the construction of storage lagoons, secondary containment (above and below ground) and other containment applications for chemicals, polluted water and produced liquids
EN ISO 14910-2:2013 Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013, Corrected version 2015-12-15)
EN ISO 7792-2:2012 Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7792-2:2012)
PREN 13361 : DRAFT 2016 GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS
I.S. EN ISO 10350-1:2017 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS (ISO 10350-1:2017)
DIN EN ISO 19069-1:2015-06 PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 19069-1:2015)
DIN EN 16506 E : 2014 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
16/30338123 DC : 0 BS EN 16993 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF STORAGE LAGOONS, SECONDARY CONTAINMENT (ABOVE AND BELOW GROUND) AND OTHER CONTAINMENT APPLICATIONS FOR CHEMICALS, POLLUTED WATER AND PRODUCED LIQUIDS
13/30276237 DC : 0 BS EN 15348 - PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLY(ETHYLENE TEREPHTHALATE) (PET) RECYCLATES
EN 16994:2018 Clay Geosynthetic Barriers - Characteristics required for use in the construction of underground structures (other than tunnels and associated structures)
DIN EN 15348 E : 2015 PLASTICS - RECYCLED PLASTICS - CHARACTERIZATION OF POLY(ETHYLENE TEREPHTHALATE) (PET) RECYCLATES
16/30338111 DC : 0 BS EN 13491 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE AS A FLUID BARRIER IN THE CONSTRUCTION OF TUNNELS AND ASSOCIATED UNDERGROUND STRUCTURES
UNE-EN ISO 1133-1:2012 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
16/30338120 DC : 0 BS EN 15382 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN TRANSPORTATION INFRASTRUCTURE
15/30304402 DC : 0 BS EN ISO 20028-2 - PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
16/30338126 DC : 0 BS EN 13492 - GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF LIQUID WASTE DISPOSAL SITES, TRANSFER STATIONS OR SECONDARY CONTAINMENT
ONORM EN ISO 14910-2 : 2013 PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013)
I.S. EN ISO 1133-1:2011 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS - PART 1: STANDARD METHOD (ISO 1133-1:2011)
UNE-EN 16506:2015 Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL)
I.S. EN ISO 20028-2:2017 PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017)
I.S. EN ISO 16396-2:2017 PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 16396-2:2017)
I.S. EN 16506:2014 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
I.S. EN 15348:2014 PLASTICS - RECYCLED PLASTICS - CHARACTERIZATION OF POLY(ETHYLENE TEREPHTHALATE) (PET) RECYCLATES
ISO 14910-2:2013 Plastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 2: Preparation of test specimens and determination of properties
DIN EN ISO 7792-2:2013-03 PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 7792-2:2012)
DIN EN ISO 11403-2 E : 2013 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES (ISO 11403-2:2012)
BS EN ISO 14910-2:2013 Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Preparation of test specimens and determination of properties
BS EN ISO 7792-2:2012 Plastics. Thermoplastic polyester (TP) moulding and extrusion materials Preparation of test specimens and determination of properties
DIN EN ISO 14910-2:2013-06 PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013)
DIN EN ISO 11403-2:2013-01 Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012)

ISO 7391-2:2006 Plastics Polycarbonate (PC) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
ISO 14910-2:2013 Plastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 2: Preparation of test specimens and determination of properties
ISO 472:2013 Plastics Vocabulary
ISO 307:2007 Plastics Polyamides Determination of viscosity number
ISO 15512:2016 Plastics Determination of water content

View more information
US$111.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.