• There are no items in your cart

ISO 18888:2017

Current
Current

The latest, up-to-date edition.

Gas turbine combined cycle power plants — Thermal performance tests
Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Language(s)

English

Published date

10-19-2017

ISO 18888:2017 specifies standard rules for preparing, conducting, evaluating and reporting thermal performance tests on combined cycle and cogeneration power plants driven by gas turbines for base and part load operation with or without supplementary firing.

ISO 18888:2017 is applicable to

- thermal performance tests for general information,

- thermal acceptance tests for determining the performance of the combined cycle plant in relation to a contractual guarantee, and

- comparative tests designed to check the performance differentials of the combined cycle and cogeneration power plants, for testing before and after modifications, upgrades or overhauls.

It can be used to determine the following thermal performance test goals and expected values, under specific operating and reference conditions within defined test boundaries:

- electrical power output;

- heat rate or thermal efficiency;

- process steam and/or district heat w/o generation of electrical power output by means of a steam turbine.

ISO 18888:2017 does not apply to individual equipment component testing, which is covered by corresponding standards.

It is not intended to be applied to the following test goals:

- environmental testing for example emissions, noise;

- vibration testing;

- operational testing;

- absolute or comparative performance of specific components of the combined cycle covered by dedicated standards (e.g. gas turbines).

Committee
ISO/TC 192
DevelopmentNote
Supersedes ISO/DIS 18888. (10/2017)
DocumentType
Standard
Pages
73
PublisherName
International Organization for Standardization
Status
Current

Standards Relationship
NEN ISO 18888 : 2017 Identical
BS ISO 18888:2017 Identical

ISO 9906:2012 Rotodynamic pumps — Hydraulic performance acceptance tests — Grades 1, 2 and 3
ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
ISO 10715:1997 Natural gas — Sampling guidelines
ISO 6976:2016 Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition
ISO 3675:1998 Crude petroleum and liquid petroleum products Laboratory determination of density Hydrometer method
ISO 12242:2012 Measurement of fluid flow in closed conduits Ultrasonic transit-time meters for liquid
ISO 3977-1:1997 Gas turbines — Procurement — Part 1: General introduction and definitions
ISO 11086:1996 Gas turbines — Vocabulary
ASTM D 4868 : 2017 : REDLINE Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels
ISO 3977-9:1999 Gas turbines Procurement Part 9: Reliability, availability, maintainability and safety
ISO 6975:1997 Natural gas — Extended analysis — Gas-chromatographic method
ISO 2533:1975 Standard Atmosphere
ISO/IEC/IEEE 60559:2011 Information technology Microprocessor Systems Floating-Point arithmetic
DIN 51900-1:2000-04 Determining the gross calorific value of solid and liquid fuels using the bomb calorimeter, and calculation of net calorific value - Part 1: General information
ISO 12185:1996 Crude petroleum and petroleum products — Determination of density — Oscillating U-tube method
ISO 2314:2009 Gas turbines — Acceptance tests
IEC 60751:2008 Industrial platinum resistance thermometers and platinum temperature sensors
ISO 10790:2015 Measurement of fluid flow in closed conduits Guidance to the selection, installation and use of Coriolis flowmeters (mass flow, density and volume flow measurements)
IEC 60953-2:1990 Rules for steam turbine thermal acceptance tests. Part 2: Method B - Wide range of accuracy for various types and sizes of turbines
ISO 6974-1:2012 Natural gas — Determination of composition and associated uncertainty by gas chromatography — Part 1: General guidelines and calculation of composition
ISO 17089-1:2010 Measurement of fluid flow in closed conduits - Ultrasonic meters for gas Part 1: Meters for custody transfer and allocation measurement
ISO 12213-2:2006 Natural gas Calculation of compression factor Part 2: Calculation using molar-composition analysis
ASTM D 1945 : 2014 : REDLINE Standard Test Method for Analysis of Natural Gas by Gas Chromatography
ISO 20765-1:2005 Natural gas Calculation of thermodynamic properties Part 1: Gas phase properties for transmission and distribution applications

View more information
US$225.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.