ISO 6162-2:2012
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
02-19-2019
French, English
12-14-2012
ISO 6162-2:2012 gives general and dimensional specifications for flanged heads, split flange clamps (FCS and FCSM), one-piece flange clamps (FC and FCM), ports and mounting surfaces applicable to four-screw, split and one-piece flange clamp type tube connectors and hose fittings for use at a pressure of 42 MPa (420 bar ). It also specifies the dimensions of the seals to be used, as well as the grooves that house the seals.
ISO 6162-2:2012 also recognizes the need to accommodate metric screw fasteners (type 1) (for DN 13 to DN 76), as well as to provide a means to use existing inch screw fasteners (type 2) (for DN 13 to DN 51).
These connections are intended for application in hydraulic systems on industrial and commercial products where it is desired to avoid the use of threaded connectors.
Surges of pressure higher than the nominal ratings will reduce the ability of the flange connections to retain the hydraulic fluid. This needs to be taken into account in the design of the hydraulic system.
DocumentType |
Standard
|
Pages |
21
|
PublisherName |
International Organization for Standardization
|
Status |
Withdrawn
|
SupersededBy | |
Supersedes |
Standards | Relationship |
BS ISO 6162-2:2012 | Identical |
NF ISO 6162-2 : 2018 | Identical |
DIN ISO 6162-2:2006-02 | Identical |
SN ISO 6162-2 : 2005 | Identical |
NEN ISO 6162-2 : 2012 | Identical |
16/30328245 DC : 0 | BS ISO 6164 - HYDRAULIC FLUID POWER - FOUR-SCREW, ONE-PIECE SQUARE FLANGE CONNECTIONS FOR USE AT PRESSURES OF 42 MPA, DN 10 TO 80 |
DIN ISO 12151-3 E : 2012 | CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS (ISO 12151-3:2010) |
SAE J 2551/3 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 3: PROCUREMENT |
BS ISO 6022:2006 | Hydraulic fluid power. Mounting dimensions for single rod cylinders, 25M Pa (250 bar) series |
BS ISO 10946:1999 | Hydraulic fluid power. Gas-loaded accumulators with separator. Selection of preferred hydraulic ports |
06/30128831 DC : DRAFT MAR 2006 | ISO 6020-1 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 1: MEDIUM SERIES |
UNE-EN ISO 4413:2011 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
DIN ISO 6022 E : 2008 | HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES |
ISO 17165-1:2007 | Hydraulic fluid power Hose assemblies Part 1: Dimensions and requirements |
UNE-EN ISO 19879:2010 | Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2010) |
EN ISO 19879:2010 | Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2010) |
DIN ISO 6022:2008-06 | HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES |
DIN EN ISO 16330:2004-08 | Reciprocating positive displacement pumps and pump units - Technical requirements (ISO 16330:2003) |
09/30202316 DC : 0 | BS EN 12514-4 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES |
BS ISO 6020-1:2007 | Hydraulic fluid power. Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Medium series |
SAE J 846 : 2015 | CODING SYSTEMS FOR IDENTIFICATION OF FLUID CONDUCTORS AND CONNECTORS |
07/30163202 DC : 0 | BS ISO 12151-3 - CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS |
DIN EN ISO 4413:2011-04 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
SAE J 515 : 2015 | SPECIFICATION FOR O-RING MATERIALS USED WITH HYDRAULIC CONNECTORS |
ISO 6164:1994 | Hydraulic fluid power Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar) |
SAE J 2593 : 2015 | INFORMATION REPORT FOR THE INSTALLATION OF FLUID CONDUCTORS AND CONNECTORS |
SAE J 518/3 : 2015 | HYDRAULIC FLANGE CLAMPS, 2-SCREW FLANGE CONNECTION TO BE USED WITH SAE J518-1, (CODE 61) CONNECTIONS WHERE ONLY LOW PRESSURE IS REQUIRED |
DIN EN ISO 19879 E : 2011 | METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS |
I.S. EN ISO 19879:2010 | METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS |
PD ISO/TS 11672:2016 | Connectors for fluid power and general use. Designation and nomenclature |
UNI ISO 12151-3 : 2012 | CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS |
BS ISO 17165-1:2007 | Hydraulic fluid power. Hose assemblies Dimensions and requirements |
ISO 6022:2006 | Hydraulic fluid power — Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series |
BS ISO 12151-3:2010 | Connections for hydraulic fluid power and general use. Hose fittings Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends |
SAE J 2551/2 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 2: GENERAL SPECIFICATIONS AND PERFORMANCE REQUIREMENTS |
SAE J 2551/1 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 1: DESIGN AND FABRICATION |
PD ISO/TS 17165-2:2013 | Hydraulic fluid power. Hose assemblies Practices for hydraulic hose assemblies |
SAE J 1677 : 2016 | TESTS AND PROCEDURES FOR CARBON STEEL AND HIGH STRENGTH LOW ALLOY STEEL TUBING |
SAE J 518/2 : 2017 | HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, 4-SCREW FLANGE CONNECTION - PART 2: 42 MPA (CODE 62) |
03/110806 DC : DRAFT JUNE 2003 | BS ISO 19879 - METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS |
SAE J 2614 : 2018 | WELDED AND COLD-DRAWN, HIGH STRENGTH (500 MPA TENSILE STRENGTH) HYDRAULIC TUBING, FOR BENDING, FLARING, COLD FORMING, WELDING AND BRAZING |
UNI ISO 17165-1 : 2012 | HYDRAULIC FLUID POWER - HOSE ASSEMBLIES - PART 1: DIMENSIONS AND REQUIREMENTS |
DIN ISO 6020-1:2010-07 | Hydraulic fluid power - Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series - Part 1: Medium series (ISO 6020-1:2007) |
SAE J 518/1 : 2013 | HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, 4-SCREW FLANGE CONNECTION - PART 1: 3.5 MPA TO 35 MPA (CODE 61) |
ISO 6020-1:2007 | Hydraulic fluid power — Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series — Part 1: Medium series |
BS EN ISO 16330:2003 | Reciprocating positive displacement pumps and pump units. Technical requirements |
ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
ISO 16330:2003 | Reciprocating positive displacement pumps and pump units Technical requirements |
ISO 19879:2010 | Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections |
EN ISO 16330 : 2003 | RECIPROCATING POSITIVE DISPLACEMENT PUMPS AND PUMP UNITS - TECHNICAL REQUIREMENTS |
EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
SAE J 1065 : 2016 | NOMINAL REFERENCE WORKING PRESSURES FOR STEEL HYDRAULIC TUBING |
ISO 12151-3:2010 | Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends |
SAE J 2551 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON AND ALLOY STEEL TUBING APPLICATIONS |
BS EN ISO 4413:2010 | Hydraulic fluid power. General rules and safety requirements for systems and their components |
UNI EN ISO 19879 : 2011 | METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS |
NF EN ISO 4413 : 2011 | HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS |
NF ISO 12151-3 : 2010 | CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS |
DIN EN ISO 19879:2011-01 | Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2010) |
BS EN ISO 19879:2010 | Metallic tube connections for fluid power and general use. Test methods for hydraulic fluid power connections |
DIN ISO 12151-3:2012-08 | Connections for hydraulic fluid power and general use - Hose fittings - Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends (ISO 12151-3:2010) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.