• There are no items in your cart

JIS B 1051:2000

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs
Available format(s)

Hardcopy , PDF

Superseded date

12-23-2016

Language(s)

English, Japanese

Published date

02-15-2008

1 - 
2 - 
3 - 
4 - 
5 - 
6 - 
7 - 
8 - 
9 - 
10 - 
11 - 
12 - 
13 - 
14 - 
15 - 
16 - 
17 - 
18 - 
19 - 
20 - 
21 - 
22 - 
23 - 
24 - 
25 - 
26 - 
27 - 
28 - 
29 - 

This Standard specifies the mechanical properties of bolts, screws and studs made of carbon steel and alloy steel when tested at an ambient temperature range of 10 degree C to 35 degree C. Products conforming to the requirements of this Standard are evaluated only in the ambient temperature range and may not retain the specified mechanical and physical properties at higher and lower temperatures. Attention is drawn to Annex A which provides examples of lower yield stress and stress at 0.2 % non-proportional elongation at elevated temperatures. At temperatures lower than the ambient temperature range, a significant change in the properties, particularly impact strength, may occur. When fasteners are to be used above or below the ambient temperature range it is the responsibility of the user to ensure that the mechanical and physical properties are suitable for his particular service conditions. Certain fasteners may not fulfill the tensile or torsional requirements of this Standard because of the geometry of the head which reduces the shear area in the head as compared to the stress area in the thread such as countersunk, raised countersunk and cheese heads (see clause 6). This Standard applies to bolts, screws and studs - with coarse pitch thread M1.6 to M39, and fine pitch thread M18 * 1 to M39 * 3; - with diameter/pitch combinations in accordance with JIS B 0205 and JIS B 0207; - with thread tolerance in accordance with JIS B 0209 and JIS B 0211; - made of carbon steel or alloy steel. It does not apply to set screws and similar threaded fasteners not under tensile stresses (see JIS B 1053). It does not specify requirements for such properties as - weldability; - corrosion-resistance; - ability to withstand temperatures above + 300 degree C (+250 degree C for 10.9) or below - 50 degree C; -- resistance to shear stress; -- fatigue resistance.

DocumentType
Standard
Pages
26
PublisherName
Japanese Standards Association
Status
Superseded
SupersededBy

JIS B 1001:1985 Diameter of clearance holes and counterbores for bolts and screws
JIS B 1058:1995 Mechanical properties of fasteners Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
JIS Z 2243:2008 Brinell hardness test - Test method
JIS B 1043:1993 Fasteners - Surface discontinuities - Part 3: Bolts, screws and studs for special requirements
JIS B 1041:1993 Fasteners - Surface discontinuities - Part 1: Bolts, screws and studs for general requirements
JIS B 1053:1999 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners not under tensile stresses
JIS B 1052:1998 Mechanical properties of steel nuts
JIS B 0207:1982 Metric Fine Screw Threads
JIS B 0211:1997 Limits Of Sizes And Tolerances For Metric Fine Screw Threads

JIS B 1084:2007 Fasteners - Torque/clamp force testing
JIS A 9401:2007 Recycled plastics medial strip block
JIS E 1107:2008 Steel bolts and nuts for fish-plates and fastenings
JIS B 1107:2004 Hexalobular socket head screws
JIS B 8602:2002 Pipe flanges for refrigerants
JIS B 1166:1995 T-Slot bolts
JIS B 0209-4:2001 ISO general purpose metric screw threads -- Tolerances -- Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing
JIS B 1060:2003 Mechanical and performance requirements of case hardened and tempered metric thread rolling screws
JIS B 1178:1994 Foundation bolts
JIS B 1091:2003 Fasteners - Acceptance inspection
JIS B 4648:1994 Hexagon socket screw keys
JIS B 1179:1994 Flat head bolts
JIS B 0209-1:2001 ISO general purpose metric screw threads - Tolerances Part 1: Principles and basic data
JIS D 3621:1982 Hose clamps for automobiles
JIS B 1052:1998 Mechanical properties of steel nuts
JIS B 1200:2007 Hexagon weld nuts with flange
JIS B 1136:2004 Hexalobular socket head cap screws
JIS B 1194:2006 Hexagon socket countersunk head screws
JIS B 1057:2001 Mechanical properties of non-ferrous metal fasteners
JIS E 1107:1998 Steel bolts and nuts for fish-plates and fastenings
JIS B 1046:2005 Fasteners - Non-electrolytically applied zinc flake coatings
JIS B 1195:1994 Weld bolts
JIS B 1083:2008 General rules for tightening of threaded fasteners
JIS B 1174:2006 Hexagon socket button head screws
JIS B 1176:2006 Hexagon socket head cap screws
JIS A 8920:2009 Earth-Moving Machinery - Falling-Object Protective Structures - Laboratory Tests And Performance Requirements
JIS B 4648:2008 Hexagon socket screw keys
JIS B 1130:2006 Screw and washer assemblies with plain washers - Washer hardness classes 200 HV and 300 HV
JIS B 2710-4:2008 Leaf springs Part 4: Specification of products
JIS B 1054-1:2001 Mechanical properties of corrosion-resistant stainless-steel fasteners Part 1: Bolts, screw and studs
JIS B 1099:2005 Fasteners - General requirements for bolts, screws, studs and nuts
JIS B 1048:2007 Fasteners - Hot dip galvanized coatings
JIS B 1054-3:2001 Mechanical properties of corrosion-resistant stainless-steel fasteners Part 3: Set screws and similar fasteners not under tensile stress
JIS B 1217:2009 Bolting for use with pipe flanges

View more information
US$45.50
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.