Name: KTA 3201.2 : 2013
Brand: KTA

COMPONENTS OF THE REACTOR COOLANT PRESSURE BOUNDARY OF LIGHT WATER REACTORS - PART 2: DESIGN AND ANALYSIS

Published date

01-12-2013

Publisher

Kerntechnischer Ausschuss

Fundamentals
1 Scope
2 General requirements and definitions
3 Load case classes as well as design, service
  and test loadings and limits of components
4 Effects on the components due to mechanical
  and thermal loadings, fluid effects and irradiation
5 Design
6 Dimensioning
7 General analysis of the mechanical behaviour
8 Component-specific analysis of the mechanical behaviour
9 Type and extent of verification of strength and pertinent
  documents to be submitted
Annex A: Dimensioning
Annex B: Requirements as to the primary stress analysis in
         case of numerical reassessments
Annex C: Calculation methods
Annex D: Brittle fracture analysis procedures
Annex E: Regulations referred to in this Safety Standard
Annex F: Changes with respect to the edition 1996-06 and
         explanations (informative)

Pertains to the design and analysis of the components of the reactor coolant pressure boundary of light water reactors made of metallic materials, which are operated up to design temperatures of 673 K (400 degrees C).

DevelopmentNote	DRAFT 2017 issued in November 2017. (02/2018)
DocumentType	Standard
PublisherName	Kerntechnischer Ausschuss
Status	Current

DIN 25459 E : 2014	REINFORCED AND PRESTRESSED CONCRETE CONTAINMENT FOR NUCLEAR POWER PLANTS
VDI 3842:2004-06	Vibrations in piping systems
KTA 3407 : 2014	PIPE PENETRATIONS THROUGH THE REACTOR CONTAINMENT VESSEL
KTA 3101.3 : 2015(R2017)	DESIGN OF REACTOR CORES OF PRESSURIZED WATER AND BOILING WATER REACTORS - PART 3: MECHANICAL AND THERMAL DESIGN
VDI 2200:2007-06	Tight flange connections - Selection, calculation, design and assembly of bolted flange connections
DIN 2413:2011-06	SEAMLESS STEEL TUBES FOR OIL- AND WATER-HYDRAULIC SYSTEMS - CALCULATION RULES FOR PIPES AND ELBOWS FOR DYNAMIC LOADS
KTA 3103 : 2015(R2017)	SHUTDOWN SYSTEMS FOR LIGHT WATER REACTORS
KTA 3205.2 : 2015 COR 2016	COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS - PART 2: COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS FOR PRESSURE AND ACTIVITY-RETAINING COMPONENTS IN SYSTEMS OUTSIDE THE PRIMARY CIRCUIT
KTA 3206 : 2014(R2017)Berichtigung:2019	BREAK PRECLUSION VERIFICATIONS FOR PRESSURE-RETAINING COMPONENTS IN NUCLEAR POWER PLANTS
KTA 3201.3 : 2007(R2012)	COMPONENTS OF THE REACTOR COOLANT PRESSURE BOUNDARY OF LIGHT WATER REACTORS - PART 3: MANUFACTURE

DIN EN ISO 898-1:2013-05	MECHANICAL PROPERTIES OF FASTENERS MADE OF CARBON STEEL AND ALLOY STEEL - PART 1: BOLTS, SCREWS AND STUDS WITH SPECIFIED PROPERTY CLASSES - COARSE THREAD AND FINE PITCH THREAD (ISO 898-1:2013)
DIN EN ISO 3506-1:2010-04	MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 1: BOLTS, SCREWS AND STUDS
DIN 2510-4:1971-08	BOLTED CONNECTIONS WITH REDUCED SHANK; STUDS
DIN 28013:2012-06	ELLIPSOIDAL HEADS
DIN EN 10253-2:2008-09	Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements
DIN EN ISO 3506-2:2010-04	MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 2: NUTS
DIN EN 13555:2014-07	Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections
DIN 267-13:2007-05	FASTENERS - TECHNICAL SPECIFICATIONS - PART 13: PARTS FOR BOLTED CONNECTIONS WITH SPECIFIC MECHANICAL PROPERTIES FOR USE AT TEMPERATURES RANGING FROM -200 DEGREE C TO +700 DEGREE C
DIN EN 10253-4:2008-06	BUTT-WELDING PIPE FITTINGS - PART 4: WROUGHT AUSTENITIC AND AUSTENITIC-FERRITIC (DUPLEX) STAINLESS STEELS WITH SPECIFIC INSPECTION REQUIREMENTS
DIN 28011:2012-06	TOROSPHERICAL HEADS