MIL-DTL-32408 Base Document:2012

Withdrawn

INTEGRAL MOTOR PUMP (IMP)

Available format(s)

PDF

Withdrawn date

05-02-2017

Publisher

US Military Specs/Standards/Handbooks

1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES

Specifies vertical or horizontal centrifugal Integral Motor Pumps (IMP) for shipboard applications on U.S. Navy ships and submarines. Pumps are to be sealless and configured for either end suction where impeller is overhung with all bearings on one side of the impeller, or in an inline configuration with the impeller positioned between two sets of bearings.

Committee	FSC 4320
DevelopmentNote	NOTICE 1 - Notice of Validation. (11/2016) NOTICE 2 - Notice of Cancellation without Replacement. (07/2017)
DocumentType	Standard
Pages	26
PublisherName	US Military Specs/Standards/Handbooks
Status	Withdrawn

NEMA MW 1000 : 2016	MAGNET WIRE
NSF 61 : 2016	DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS
QQ-N-286 Revision G:2000	NICKEL-COPPER ALUMINUM ALLOY, WROUGHT (UNS N05500)
MIL-STD-740-1 Base Document:1986	AIRBORNE SOUND MEASUREMENTS AND ACCEPTANCE CRITERIA OF SHIPBOARD EQUIPMENT
HI 1.6 : 2000	CENTRIFUGAL PUMP TESTS
MIL E 917 : E	ELECTRIC POWER EQUIPMENT, BASIC REQUIREMENTS (NAVAL SHIPBOARD USE)
ASTM B 473 : 2007	Standard Specification for UNS N08020, UNS N08024, and UNS N08026 Nickel Alloy Bar and Wire
DOD-STD-1399-301 Revision A:1986	INTERFACE STANDARD FOR SHIPBOARD SYSTEMS SECTION 301A SHIP MOTION AND ATTITUDE (METRIC)
ASTM B 584 : 2014 : REDLINE	Standard Specification for Copper Alloy Sand Castings for General Applications
IEC TS 61934:2011	Electrical insulating materials and systems - Electrical measurement of partial discharges (PD) under short rise time and repetitive voltage impulses
HI 9.1 - 9.5 : 2015	PUMPS - GENERAL GUIDELINES
MIL-DTL-1222 Revision J:2000	STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; GENERAL SPECIFICATION FOR
MIL-STD-1687 Revision A:1987	THERMAL SPRAY PROCESSES FOR NAVAL SHIP MACHINERY AND ORDNANCE APPLICATIONS
MIL-DTL-17060 Revision G:2009	MOTORS, ALTERNATING CURRENT, INTEGRAL-HORSEPOWER, SHIPBOARD USE
MIL-HDBK-454 Revision B:2007	GENERAL GUIDELINES FOR ELECTRONIC EQUIPMENT
IEC TS 60034-18-41:2006	Rotating electrical machines - Part 18-41: Qualification and type tests for Type I electrical insulation systems used in rotating electrical machines fed from voltage converters
ASTM D 5363 : 2016 : REDLINE	Standard Specification for Anaerobic Single-Component Adhesives (AN)
NAVSEA T9074 AS GIB 010/271 : 0	REQUIREMENTS FOR NONDESTRUCTIVE TESTING METHODS
MIL-STD-740-2 Base Document:1986	STRUCTURE BORNE VIBRATORY ACCELERATION MEASUREMENTS ACCEPTANCE CRITERIA OF SHIPBOARD EQUIPMENT
NAVSEA S9074 AR GIB 010/278 : 0	REQUIREMENTS FOR FABRICATION WELDING AND INSPECTION, AND CASTING INSPECTION AND REPAIR FOR MACHINERY, PIPING, AND PRESSURE VESSELS
FED-STD-H28-2 Revision B:1991	Screw-Thread Standards for Federal Services Section 2 Unified Inch Screw Threads- UN and UNR Thread Forms
ANSI S2.19 : 0	MECHANICAL VIBRATION - BALANCE QUALITY REQUIREMENTS OF RIGID ROTORS - PART 1: DETERMINATION OF PERMISSIBLE RESIDUAL UNBALANCE, INCLUDING MARINE APPLICATIONS
ASTM B 61 : 2015 : REDLINE	Standard Specification for Steam or Valve Bronze Castings
MIL-STD-882 Revision E:2012	System Safety
MIL-STD-461 Revision G:2015	REQUIREMENTS FOR THE CONTROL OF ELECTROMAGNETIC INTERFERENCE CHARACTERISTICS OF SUBSYSTEMS AND EQUIPMENT
MIL-STD-777 Revision F:2012	SCHEDULE OF PIPING, VALVES, FITTINGS, AND ASSOCIATED PIPING COMPONENTS FOR NAVAL SURFACE SHIPS
IEEE 115-2009 REDLINE	IEEE Guide for Test Procedures for Synchronous Machines Part I—Acceptance and Performance Testing Part II—Test Procedures and Parameter Determination for Dynamic Analysis
MIL S 901 : D	SHOCK TESTS, HI [HIGH IMPACT] SHIPBOARD MACHINERY, EQUIPMENT AND SYSTEMS, REQUIREMENTS FOR
ASME B16.5 : 2017	PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD
MIL-PRF-32168 Base Document:2004	VARIABLE SPEED DRIVE SYSTEM FOR INDUCTION AND SYNCHRONOUS MACHINES
MIL-STD-1474 Revision E:2015	NOISE LIMITS
HI 1.1 - 1.2 : 2014	ROTODYNAMIC CENTRIFUGAL PUMPS FOR NOMENCLATURE AND DEFINITIONS
MIL-DTL-15024 Revision F:1997	Plates and Tags for Identification of Equipment, General Specification for
FED-STD-H28 Revision A:1994	Screw-Thread Standards for Federal Services
MIL-DTL-15090 Revision E:2010	ENAMEL, EQUIPMENT, LIGHT GRAY, (NAVY FORMULA NO. 111)
MIL-PRF-20042 Revision F:2015	FLANGES, PIPE, BRONZE (SILVER BRAZING)
MIL-STD-167-1 Revision A:2005	MECHANICAL VIBRATIONS OF SHIPBOARD EQUIPMENT (TYPE 1 - ENVIRONMENTAL AND TYPE 2 - INTERNALLY EXCITED)