Name: NASA HDBK 8739.19-2 : 2010
Brand: NASA

MEASURING AND TEST EQUIPMENT SPECIFICATIONS - NASA MEASUREMENT QUALITY ASSURANCE HANDBOOK - ANNEX 2

Published date

01-01-2010

Publisher

National Aeronautics and Space Administration

FOREWORD
ACKNOWLEDGEMENTS
EXECUTIVE SUMMARY
READER'S GUIDE
ACRONYMS AND INITIALISMS
CHAPTER 1: INTRODUCTION
CHAPTER 2: MEASURING AND TEST EQUIPMENT
CHAPTER 3: PERFORMANCE CHARACTERISTICS
CHAPTER 4: ESTABLISHING PERFORMANCE CHARACTERISTICS
CHAPTER 5: DEVELOPING SPECIFICATIONS
CHAPTER 6: VERIFYING AND MODIFYING SPECIFICATIONS
CHAPTER 7: REPORTING SPECIFICATIONS
CHAPTER 8: OBTAINING SPECIFICATIONS
CHAPTER 9: INTERPRETING SPECIFICATIONS
CHAPTER 10: VALIDATING CONFORMANCE TO SPECIFICATIONS
CHAPTER 11: APPLYING SPECIFICATIONS
CHAPTER 12: FIRMWARE AND SOFTWARE-BASED SPECIFICATIONS
CHAPTER 13: MEASUREMENT QUALITY AND SPECIFICATIONS
APPENDIX A - TERMS AND DEFINITIONS
APPENDIX B - STANDARDS FOR THE TESTING AND REPORTING OF MTE
PERFORMANCE CHARACTERISTICS
APPENDIX C - GENERALIZED TRANSFER FUNCTIONS FOR SELECTED MTE
APPENDIX D - LOAD MEASUREMENT SYSTEM ANALYSIS
REFERENCES

Specifies technical information and best practices relevant to MTE development, selection, acceptance testing, calibration and end-use.

DocumentType	Standard
PublisherName	National Aeronautics and Space Administration
Status	Current

NASA-STD-8739.12:2018	METROLOGY & CALIBRATION
NASA HDBK 8739.19-3 : 2010	MEASUREMENT UNCERTAINTY ANALYSIS PRINCIPLES AND METHODS - NASA MEASUREMENT QUALITY ASSURANCE HANDBOOK - ANNEX 3
NASA KSC STD Z 0017 : 2014	ENGINEERING ANALYSIS, THERMAL/FLUID, STANDARD FOR
NASA SSTD 8070 0093 : 2011	CLASSIFICATION OF PRESSURE TRANSDUCERS

NASA HDBK 8739.19-3 : 2010	MEASUREMENT UNCERTAINTY ANALYSIS PRINCIPLES AND METHODS - NASA MEASUREMENT QUALITY ASSURANCE HANDBOOK - ANNEX 3
MIL-STD-810 Revision G:2008	ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS
ANSI/NCSL Z540 3 : 2006(R2013)	REQUIREMENTS FOR THE CALIBRATION OF MEASURING AND TEST EQUIPMENT
MIL-STD-1540 Revision D:1999	TEST REQUIREMENTS FOR LAUNCH, UPPER-STAGE, AND SPACE VEHICLES
MIL-STD-45662 Revision A:1988	CALIBRATION SYSTEMS REQUIREMENTS
ISO 2859-0:1995	Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system
NCSL RP 3 : 2007	CALIBRATION PROCEDURES
ASTM E 2281 : 2015 : REDLINE	Standard Practice for Process Capability and Performance Measurement
ANSI/NCSL Z540 1 : 94(R2002)	CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS
ASTM E 2587 : 2016 : REDLINE	Standard Practice for Use of Control Charts in Statistical Process Control
NASA HDBK 8739.19-4 : 2010	ESTIMATION AND EVALUATION OF MEASUREMENT DECISION RISK - NASA MEASUREMENT QUALITY ASSURANCE HANDBOOK - ANNEX 4
ISA 37.3 : 1982	SPECIFICATIONS AND TESTS FOR STRAIN GAGE PRESSURE TRANSDUCERS
ISA 37.1 : 1975	ELECTRICAL TRANSDUCER NOMENCLATURE AND TERMINOLOGY
MIL-STD-202 Revision H:2015	ELECTRONIC AND ELECTRICAL COMPONENT PARTS
MIL-STD-1629 Revision A:1980	PROCEDURES FOR PERFORMING A FAILURE MODE, EFFECTS AND CRITICALITY ANALYSIS
ISA 51.1 : 1979	PROCESS INSTRUMENTATION TERMINOLOGY
MIL-STD-105 Revision E:1989	SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES
MIL-STD-781 Revision D:1986	RELIABILITY TESTING FOR ENGINEERING DEVELOPMENT, QUALIFICATION AND PRODUCTION
ASQ Z1.9:2003 (R2013)	Sampling Procedures And Tables For Inspection By Variables For Percent Nonconforming