Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search

NF ISO 4413 : 1999

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

HYDRAULIC FLUID POWER - GENERAL RULES RELATING TO SYSTEMS
Superseded date

03-01-2011

Published date

01-12-2013

Publisher

Association Francaise de Normalisation

1 Domaine d'application
2 Références normatives
3 Définitions
4 Exigences
   4.1 Généralités
   4.2 Phénomènes dangereux
   4.3 Exigences de sécurité
   4.4 Exigences relatives à un système
   4.5 Conditions d'implantation
5 Conception du système
   5.1 Schémas de circuit
   5.2 Identification
   5.3 Installation, utilisation et maintenance
   5.4 Utilisation de pièces normalisées
   5.5 Joints et dispositifs d'étanchéité
   5.6 Consignes de maintenance et d'utilisation
   5.7 Manuels d'utilisation et de maintenance
   5.8 Orifices
   5.9 Température du système
6 Composants de transformation de l'énergie
   6.1 Pompes et moteurs hydrauliques
   6.2 Vérins
   6.3 Accumulateurs à gaz
7 Soupapes et distributeurs
   7.1 Sélection
   7.2 Montage
   7.3 Blocs collecteurs
   7.4 Distributeurs à commande électrique
   7.5 Plaques indicatrices de symboles
   7.6 Réglages
   7.7 Dépose
8 Fluides et composants de conditionnement
   8.1 Fluides hydrauliques
   8.2 Réservoirs de fluide
   8.3 Filtration et conditionnement du fluide
   8.4 Échangeurs de chaleur
9 Tuyauteries
   9.1 Exigences générales
   9.2 Exigences relatives aux tuyaux et tubes
   9.3 Supports de tuyauteries
   9.4 Corps étrangers
   9.5 Assemblages de tuyauteries flexibles
   9.6 Raccords rapides
10 Systèmes de commande
   10.1 Mouvements incontrolés
   10.2 Protection des systèmes
   10.3 Composants
   10.4 Systèmes de commande à servodistributeurs ou à
        distributeurs proportionnels
   10.5 Autres considérations de conception
   10.6 Emplacement des commandes
   10.7 Commandes d'urgence
11 Diagnostics et surveillance
   11.1 Mesurage de la pression
   11.2 Prélèvement d'un échantillon de fluide
   11.3 Controle de la température
12 Nettoyage et peinture
13 Préparation pour le transport
   13.1 Identification des tuyauteries
   13.2 Emballage
   13.3 Obturation des ouvertures
   13.4 Aménagements pour le transport
14 Réception du matériel
   14.1 Essais de conformité
   14.2 Bruit
   14.3 Fuite de fluide
   14.4 Documents finaux à fournir
   14.5 Modifications
   14.6 Vérification
15 Phrase d'identification (Référence à la présente Norme
   internationale)
Annexe A (informative) - Points nécessitant un accord entre
                         le fournisseur et l'acheteur
Annexe B (informative) - Liste des phénomènes dangereux
Annexe C (informative) - Liste des références croisées
                         ISO 4413/EN 982
Annexe D (informative) - Bibliographie
Index

La présente Norme internationale fournit des règles générales relatives aux systèmes hydrauliques des machines utilisées dans les procédés de fabrication industrielle. Elle est destinée à servir de guide à la fois aux fournisseurs et aux acheteurs, afin d'assurer: a) la sécurité; b) un fonctionnement continu du système; c) une maintenance facile et économique; d) la pérennité du système.

DevelopmentNote
Indice de Classement: E48-201 Supersedes NFE 48 201. (04/2003)
DocumentType
Standard
PublisherName
Association Francaise de Normalisation
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ISO 4413:2010 Identical

NF ISO 20966 : 2007 AUTOMATIC MILKING INSTALLATIONS - REQUIREMENTS AND TESTING
NF ISO 15217 : 2002 FLUID POWER SYSTEMS AND COMPONENTS - 16 MM SQUARE ELECTRICAL CONNECTOR WITH EARTH CONTACT - CHARACTERISTICS AND REQUIREMENTS

NF ISO 10372 : 1993 HYDRAULIC FLUID POWER - FOUR- AND FIVE-PORTS SERVO VALVES - MOUNTING SURFACES
NFE 48 055 : 1986 TRANSMISSIONS HYDRAULIQUES - BRIDES ET IMPLANTATIONS RECTANGULAIRES AVEC COLLETS ENCASTRES PN 250 ET PN 400 - DIMENSIONS
NF EN 60204-1 : 2006 AMD 1 2009 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
NFE 48 650 : 1986 HYDRAULIC FLUID POWER - FLUIDS - METHODS FOR BOTTLE SAMPLING FROM LINES OF AN OPERATING SYSTEM
ISO 4401:2005 Hydraulic fluid power — Four-port directional control valves — Mounting surfaces
ISO 5598:2008 Fluid power systems and components Vocabulary
ISO 6263:2013 Hydraulic fluid power — Compensated flow-control valves — Mounting surfaces
ISO 12151-2:2003 Connections for hydraulic fluid power and general use — Hose fittings — Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24 degree cone connector ends with O-rings
NF ISO 7368 : 1990 HYDRAULIC FLUID POWER - TWO-PORT SLIP-IN CARTRIDGE VALVES - CAVITIES
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
ISO 6162:1994 Hydraulic fluid power Four-screw split-flange connections for use at pressures of 2,5 MPa to 40 MPa (25 bar to 400 bar) Type I metric series and type II inch series
NF ISO 619952 : 1995 FLUID POWER SYSTEMS AND COMPONENTS - TWO-PIN ELECTRICAL PLUG CONNECTORS WITH EARTH CONTACT - CHARACTERISTICS AND REQUIREMENTS
NF EN 60529 : 92 AMD 2 2014 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE)
ISO 7789:2007 Hydraulic fluid power Two-, three- and four-port screw-in cartridge valves Cavities
ISO 12151-5:2007 Connections for hydraulic fluid power and general use — Hose fittings — Part 5: Hose fittings with ISO 8434-2 37 degree flared ends
ISO 8434-2:2007 Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors
ISO 6264:1998 Hydraulic fluid power — Pressure-relief valves — Mounting surfaces
NF ISO 7790 : 2013 HYDRAULIC FLUID POWER - FOUR-PORT MODULAR STACK VALVES AND FOUR-PORT DIRECTIONAL CONTROL VALVES, SIZES 02, 03, 05, 07, 08 AND 10 - CLAMPING DIMENSIONS
ISO 5781:2016 Hydraulic fluid power Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves Mounting surfaces
ISO 12151-3:2010 Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
ISO 8434-3:2005 Metallic tube connections for fluid power and general use — Part 3: O-ring face seal connectors
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
ISO 6164:1994 Hydraulic fluid power Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar)
NF ISO 1219-2 : 2012 FLUID POWER SYSTEMS AND COMPONENTS - GRAPHIC SYMBOLS AND CIRCUITS DIAGRAMS - PART 2: CIRCUIT DIAGRAMS
ISO 8434-4:1995 Metallic tube connections for fluid power and general use Part 4: 24 degree cone connectors with O-ring weld-on nipples
ISO 12151-1:2010 Connections for hydraulic fluid power and general use — Hose fittings — Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends
ISO 10763:1994 Hydraulic fluid power Plain-end, seamless and welded precision steel tubes Dimensions and nominal working pressures
NFE 48 000 : 1987 FLUID POWER SYSTEM - VOCABULARY
ISO 12151-4:2007 Connections for hydraulic fluid power and general use Hose fittings Part 4: Hose fittings with ISO 6149 metric stud ends
NF ISO 6149-1 : 1994 CONNECTIONS FOR FLUID POWER AND GENERAL USE - PORTS AND STUD ENDS WITH ISO 261 THREADS AND O-RING SEALING - PART 1: PORTS WITH O-RING SEAL IN TRUNCATED HOUSING
ISO 4021:1992 Hydraulic fluid power — Particulate contamination analysis — Extraction of fluid samples from lines of an operating system
NFE 48 423 : 1989 TRANSMISSIONS HYDRAULIQUES - DISTRIBUTEURS A 4 ORIFICES, REDUCTEURS DE PRESSION, SOUPAPES DE SEQUENCE, SOUPAPES DE DECHARGE, SOUPAPES D'ETRANGLEMENT, CLAPETS DE NON RETOUR, REGULATEURS DE DEBIT, LIMITEURS DE PRESSION - PLAN DE POSE
NFE 48 054 : 1998 TRANSMISSIONS HYDRAULIQUES - BRIDES CARREES MONOBLOC AVEC COLLETS ENCASTRES - PN 250 ET PN 400 - DIMENSIONS
NF EN ISO 11688-1 : 2009 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 1: PLANNING
NF ISO 4400 : 1995 FLUID POWER SYSTEMS AND COMPONENTS - THREE-PIN ELECTRICAL PLUG CONNECTORS WITH EARTH CONTACT - CHARACTERISTICS AND REQUIREMENTS

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us