• There are no items in your cart

PREN ISO 13705 : DRAFT 2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FIRED HEATERS FOR GENERAL REFINERY SERVICE
Superseded date

12-01-2012

Published date

01-12-2013

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, and abbreviations
4 General
5 Proposals
6 Design considerations
7 Tubes
8 Headers
9 Piping, terminals and manifolds
10 Tube suppports
11 Refractories and insulation
12 Structures and appurtenances
13 Stacks, ducts and breeching
14 Burners and auxiliary equipment
15 Instrument and auxiliary connections
16 Shop fabrication and field erection
17 Inspection, examination and testing
Annex A (informative) - Equipment data sheets
Annex B (informative) - Purchaser's checklist
Annex C (informative) - Proposed shop-assembly conditions
Annex D (normative) - Stress curves for use in the design
        of tube-support elements
Annex E (normative) - Centrifugal fans for fired-heater
        systems
Annex F (normative) - Air preheat systems for
        fired-process heaters
Annex G (informative) - Measurement of efficiency
        of fired-process heaters
Annex H (informative) - Stack design
ANNEX I (informative) - Measurement of noise from
        fired-process heaters
Bibliography

Describes requirements and gives recommendations for the design, materials, fabrication, inspection, testing, preparation for shipment, and erection of fired heaters, air preheaters, fans and burners for general refinery service.

Committee
TC 12
DocumentType
Draft
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

Standards Relationship
11/30246055 DC : 0 Identical

ASTM C 553 : 2013 : REDLINE Standard Specification for Mineral Fiber Blanket Thermal Insulation for Commercial and Industrial Applications
ISO 15649:2001 Petroleum and natural gas industries — Piping
AWS D14.6 : 1996 SPECIFICATION FOR WELDING OF ROTATING ELEMENTS OF EQUIPMENT
AMCA 803 : 2002(R2008) INDUSTRIAL PROCESS/POWER GENERATION FANS: SITE PERFORMANCE TEST STANDARD
API 500 : 2012 RECOMMENDED PRACTICE FOR CLASSIFICATION OF LOCATIONS FOR ELECTRICAL INSTALLATIONS AT PETROLEUM FACILITIES CLASSIFIED AS CLASS 1, DIVISION 1 AND DIVISION 2
ABMA 9 : 2015 LOAD RATINGS AND FATIGUE LIFE FOR BALL BEARINGS
ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
ISO 10684:2004 Fasteners — Hot dip galvanized coatings
ASTM A 297/A297M : 2017 : REDLINE Standard Specification for Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant, for General Application
API 535 : 2014 BURNERS FOR FIRED HEATERS IN GENERAL REFINERY SERVICES
ISO 1940-1:2003 Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances
ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
ISO 13704:2007 Petroleum, petrochemical and natural gas industries — Calculation of heater-tube thickness in petroleum refineries
ASTM C 612 : 2014 : REDLINE Standard Specification for Mineral Fiber Block and Board Thermal Insulation
AMCA 210 : 2016 LABORATORY METHODS OF TESTING FANS FOR CERTIFIED AERODYNAMIC PERFORMANCE RATING
ASTM C 27 : 1998 Standard Classification of Fireclay and High-Alumina Refractory Brick
ASTM C 332 : 2017 : REDLINE Standard Specification for Lightweight Aggregates for Insulating Concrete
MSS SP 53 : 2012 QUALITY STANDARD FOR STEEL CASTINGS AND FORGINGS FOR VALVES, FLANGES, FITTINGS, AND OTHER PIPING COMPONENTS - MAGNETIC PARTICLE EXAMINATION METHOD
NFPA 70 : 2017 NATIONAL ELECTRICAL CODE
SSPC-SP 6 : 2015 COMMERCIAL BLAST CLEANING
MSS SP 93 : 2014 QUALITY STANDARD FOR STEEL CASTINGS AND FORGINGS FOR VALVES, FLANGES, FITTINGS, AND OTHER PIPING COMPONENTS - LIQUID PENETRANT EXAMINATION METHOD
EN 10025-2:2004/AC:2005 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
API 610 : 2010 CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries
MSS SP 55 : 2011 QUALITY STANDARD FOR STEEL CASTINGS FOR VALVES, FLANGES, FITTINGS, AND OTHER PIPING COMPONENTS - VISUAL METHOD FOR EVALUATION OF SURFACE IRREGULARITIES
AMCA 802 : 2002(R2008) INDUSTRIAL PROCESS/POWER GENERATION FANS - ESTABLISHING PERFORMANCE USING LABORATORY MODELS
AWS D1.1 : 2000 STRUCTURAL WELDING CODE - STEEL
ASTM A 515/A515M : 2017 : REDLINE Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service
AMCA 203 : 90(R2011) FIELD PERFORMANCE MEASUREMENT OF FAN SYSTEMS
API 536 : 2017 POST-COMBUSTION NO[X] CONTROL FOR FIRED EQUIPMENT IN GENERAL REFINERY AND PETROCHEMICAL SERVICES
API 555 : 2013 PROCESS ANALYZERS
AMCA 801 : 2001(R2008) INDUSTRIAL PROCESS/POWER GENERATION FANS - SPECIFICATIONS GUIDELINES
AISC S326 : 1978 SPECIFICATION FOR THE DESIGN, FABRICATION AND ERECTION OF STRUCTURAL STEEL FOR BUILDINGS (WITH COMMENTARY)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.