SR CEN/TS 15534-3:2007

Superseded View Superseded By

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Preview

WOOD-PLASTICS COMPOSITES (WPC) - PART 3: CHARACTERISATION OF WPC PRODUCTS

Publisher: National Standards Authority of Ireland

Published:

Available Formats: PDF - English
More Info on product formats

Table of Contents - (Show below) - (Hide below)

Foreword
1 Scope
2 Normative references
3 Characterisation of WPC products
Annex A (informative) Technical data templates

Abstract - (Show below) - (Hide below)

Describes the required and optional properties of wood-plastics composite (WPC) products. It is intended to be used as a basis for the specifications of WPC products.

General Product Information - (Show below) - (Hide below)

Published
Document Type	Standard
Status	Superseded
Publisher	National Standards Authority of Ireland
Pages
ISBN
Superseded By	I.S. EN 15534-5:2014 I.S. EN 15534-4:2014

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
CEN/TS 15534-3 : 2007	Identical

Standards Referencing This Book - (Show below) - (Hide below)

ISO 7724-1 : 1984	PAINTS AND VARNISHES - COLORIMETRY - PART 1: PRINCIPLES
ISO 6603-2 : 2000(R2015)	PLASTICS - DETERMINATION OF PUNCTURE IMPACT BEHAVIOUR OF RIGID PLASTICS - PART 2: INSTRUMENTED IMPACT TESTING
EN 321 : 2001	WOOD-BASED PANELS - DETERMINATION OF MOISTURE RESISTANCE UNDER CYCLIC TEST CONDITIONS
EN ISO 9142 : 2003	ADHESIVES - GUIDE TO THE SELECTION OF STANDARD LABORATORY AGEING CONDITIONS FOR TESTING BONDED JOINTS
EN 310 : 1993	WOOD-BASED PANELS - DETERMINATION OF MODULUS OF ELASTICITY IN BENDING AND OF BENDING STRENGTH
ENV 1156 : DRAFT 1998	WOOD-BASED PANELS - DETERMINATION OF DURATION OF LOAD AND CREEP FACTORS
EN 317 : 1993	PARTICLEBOARDS AND FIBREBOARDS - DETERMINATION OF SWELLING IN THICKNESS AFTER IMMERSION IN WATER
EN 13446 : 2002	WOOD-BASED PANELS - DETERMINATION OF WITHDRAWAL CAPACITY OF FASTENERS
ISO 7724-2 : 1984	PAINTS AND VARNISHES - COLORIMETRY - PART 2: COLOUR MEASUREMENT
ISO 11925-2 : 2010	REACTION TO FIRE TESTS - IGNITABILITY OF PRODUCTS SUBJECTED TO DIRECT IMPINGEMENT OF FLAME - PART 2: SINGLE-FLAME SOURCE TEST
ISO 9142 : 2003(R2019)	ADHESIVES - GUIDE TO THE SELECTION OF STANDARD LABORATORY AGEING CONDITIONS FOR TESTING BONDED JOINTS
EN 789 : 2004	TIMBER STRUCTURES - TEST METHODS - DETERMINATION OF MECHANICAL PROPERTIES OF WOOD BASED PANELS
EN ISO 179-1 : 2010	PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 1: NON-INSTRUMENTED IMPACT TEST
EN 1383 : 2016	TIMBER STRUCTURES - TEST METHODS - PULL THROUGH RESISTANCE OF TIMBER FASTENERS
EN 13823 : 2010 + A1 2014	REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - BUILDING PRODUCTS EXCLUDING FLOORINGS EXPOSED TO THE THERMAL ATTACK BY A SINGLE BURNING ITEM
ISO 7724-3 : 1984	PAINTS AND VARNISHES - COLORIMETRY - PART 3: CALCULATION OF COLOUR DIFFERENCES
EN ISO 9239-1 : 2010	REACTION TO FIRE TESTS FOR FLOORINGS - PART 1: DETERMINATION OF THE BURNING BEHAVIOUR USING A RADIANT HEAT SOURCE
EN 13893 : 2002	RESILIENT, LAMINATE AND TEXTILE FLOOR COVERINGS - MEASUREMENT OF - DYNAMIC COEFFICIENT OF FRICTION ON DRY FLOOR SURFACES
EN ISO 4628-6 : 2011	PAINTS AND VARNISHES - EVALUATION OF DEGRADATION OF COATINGS - DESIGNATION OF QUANTITY AND SIZE OF DEFECTS, AND OF INTENSITY OF UNIFORM CHANGES IN APPEARANCE - PART 6: ASSESSMENT OF DEGREE OF CHALKING BY TAPE METHOD (ISO 4628-6:2011)
EN ISO 6603-2 : 2000	PLASTICS - DETERMINATION OF PUNCTURE IMPACT BEHAVIOUR OF RIGID PLASTICS - PART 2: INSTRUMENTED PUNCTURE TEST
EN 318 : 2002	WOOD BASED PANELS - DETERMINATION OF DIMENSIONAL CHANGES ASSOCIATED WITH CHANGES IN RELATIVE HUMIDITY
ISO 179-1 : 2010(R2015)	PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 1: NON-INSTRUMENTED IMPACT TEST
ISO 877 : 1994	PLASTICS - METHODS OF EXPOSURE TO DIRECT WEATHERING, TO WEATHERING USING GLASS-FILTERED DAYLIGHT, AND TO INTENSIFIED WEATHERING BY DAYLIGHT USING FRESNEL MIRRORS
ISO 4892-2 : 2013(R2018)	PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 2: XENON-ARC LAMPS
ISO 4628-6 : 2011(R2017)	PAINTS AND VARNISHES - EVALUATION OF DEGRADATION OF COATINGS - DESIGNATION OF QUANTITY AND SIZE OF DEFECTS, AND OF INTENSITY OF UNIFORM CHANGES IN APPEARANCE - PART 6: ASSESSMENT OF DEGREE OF CHALKING BY TAPE METHOD
CEN/TS 15534-1 : 2007	WOOD-PLASTICS COMPOSITES (WPC) - PART 1: TEST METHODS FOR CHARACTERISATION OF WPC MATERIALS AND PRODUCTS
CEN/TS 15534-2 : 2007	WOOD-PLASTICS COMPOSITES (WPC) - PART 2: CHARACTERISATION OF WPC MATERIALS
EN ISO 877 : 1996
ISO 9239-1 : 2010(R2015)	REACTION TO FIRE TESTS FOR FLOORINGS - PART 1: DETERMINATION OF THE BURNING BEHAVIOUR USING A RADIANT HEAT SOURCE
EN 927-6 : 2006	PAINTS AND VARNISHES - COATING MATERIALS AND COATING SYSTEMS FOR EXTERIOR WOOD - PART 6: EXPOSURE OF WOOD COATINGS TO ARTIFICIAL WEATHERING USING FLUORESCENT UV LAMPS AND WATER
EN ISO 4892-2 : 2013	PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 2: XENON-ARC LAMPS (ISO 4892-2:2013)
EN ISO 11925-2 : 2010 COR 2011	REACTION TO FIRE TESTS - IGNITABILITY OF PRODUCTS SUBJECTED TO DIRECT IMPINGEMENT OF FLAME - PART 2: SINGLE-FLAME SOURCE TEST
ISO 2813:2014(R2019)	PAINTS AND VARNISHES - DETERMINATION OF GLOSS VALUE AT 20 DEGREES, 60 DEGREES AND 85 DEGREES
EN ISO 2813 : 2014	PAINTS AND VARNISHES - DETERMINATION OF GLOSS VALUE AT 20 DEGREES, 60 DEGREES AND 85 DEGREES (ISO 2813:2014)

Add To Cart

Product Format

Quantity

add to cart

SR CEN/TS 15534-3:2007

Table of Contents - (Show below) - (Hide below)

Abstract - (Show below) - (Hide below)

General Product Information - (Show below) - (Hide below)

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Standards Referencing This Book - (Show below) - (Hide below)

Add To Cart

Publisher

Category

Sub Category

Access your standards online with a subscription?