• There are no items in your cart

UNI EN 13507 : 2010

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

THERMAL SPRAYING - PRE-TREATMENT OF SURFACES OF METALLIC PARTS AND COMPONENTS FOR THERMAL SPRAYING
Superseded date

07-23-2013

Published date

01-01-2010

Foreword
1 Scope
2 Normative references
3 Principles
4 Methods of surface preparation
5 Preheating
6 Masking of areas not to be coated
7 Effect of pre-treatment on the fatigue strength
Bibliography

Describes the processing of surface preparation for thermal spraying. Also applies for production of new parts as well as for the repair of worn parts.

DocumentType
Standard
PublisherName
Ente Nazionale Italiano di Unificazione (UNI)
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
NS EN 13507 : 2010 Identical
UNE-EN 13507:2011 Identical
BS EN 13507:2010 Identical
NBN EN 13507 : 2010 Identical
ONORM EN 13507 : 2010 Identical
SN EN 13507 : 2010 Identical
NF EN 13507 : 2010 Identical
EN 13507:2010 Identical
DIN EN 13507:2016-07 (Draft) Identical
I.S. EN 13507:2010 Identical
NEN EN 13507 : 2010 Identical

ISO 11124-4:1993 Preparation of steel substrates before application of paints and related products Specifications for metallic blast-cleaning abrasives Part 4: Low-carbon cast-steel shot
ISO 2063:2005 Thermal spraying Metallic and other inorganic coatings Zinc, aluminium and their alloys
ISO 11126-9:1999 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 9: Staurolite
ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
EN ISO 11124-2:1997 Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 2: Chilled-iron grit (ISO 11124-2:1993)
ISO 11124-3:1993 Preparation of steel substrates before application of paints and related products Specifications for metallic blast-cleaning abrasives Part 3: High-carbon cast-steel shot and grit
ISO 11126-5:1993 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 5: Nickel refinery slag
ISO 11126-8:1993 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 8: Olivine sand
ISO 8503-2:2012 Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure
ISO 11126-6:1993 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 6: Iron furnace slag
ISO 11126-4:1993 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 4: Coal furnace slag
EN ISO 11126-6:1997 Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 6: Iron furnace slag (ISO 11126-6:1993)
EN ISO 8503-3:2012 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile - Focusing microscope procedure (ISO 8503-3:2012)
ISO 8503-3:2012 Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Focusing microscope procedure
EN ISO 11126-8:1997 Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 8: Olivine sand (ISO 11126-8:1993)
ISO 11124-1:1993 Preparation of steel substrates before application of paints and related products Specifications for metallic blast-cleaning abrasives Part 1: General introduction and classification
ISO 11126-1:1993 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 1: General introduction and classification
EN 15520:2007 Thermal spraying - Recommendations for constructional design of components with thermally sprayed coatings
ISO 11126-10:2017 Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 10: Almandite garnet
EN ISO 11126-4:1998 Preparation of steel substrates before application of paintsand related products - Specifications for non-metallic blast-cleaning abrasives - Part 4: Coal furnace slag (ISO 11126-4:1993)
EN ISO 8503-1:2012 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces (ISO 8503-1:2012)
EN ISO 11126-7:1999 Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 7: Fused aluminium oxide (ISO 11126-7:1995)
ISO 11126-3:1993 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 3: Copper refinery slag
EN ISO 8503-2:2012 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure (ISO 8503-2:2012)
ISO 11124-2:1993 Preparation of steel substrates before application of paints and related products Specifications for metallic blast-cleaning abrasives Part 2: Chilled-iron grit
ISO 12944-4:2017 Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 4: Types of surface and surface preparation
EN ISO 11126-3:1997 Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 3: Copper refinery slag (ISO 11126-3:1993)
EN ISO 2063:2005 Thermal spraying - Metallic and other inorganic coatings - Zinc, aluminium and their alloys (ISO 2063:2005)
ISO 8503-1:2012 Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces
EN ISO 11126-9:2004 Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 9: Staurolite (ISO 11126-9:1999)
EN ISO 8503-4:2012 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile - Stylus instrument procedure (ISO 8503-4:2012)
EN ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings (ISO 8501-1:2007)
ISO 8503-4:2012 Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Stylus instrument procedure
EN ISO 11124-4:1997 Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 4: Low-carbon cast-steel shot (ISO 11124-4:1993)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.