Name: UNI EN ISO 11403-1 : 2014
Brand: UNI

UNI EN ISO 11403-1 : 2014

Superseded

View Superseded by

PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES

Superseded date

08-29-2022

Published date

01-01-2014

Publisher

Ente Nazionale Italiano di Unificazione (UNI)

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Specimen preparation
5 Conditioning
6 Test requirements
7 Presentation of data
8 Precision
Bibliography

Defines test procedures for the acquisition and presentation of multipoint data on the following mechanical properties of plastics: - dynamic modulus; - tensile properties at constant test speed; - ultimate stress and strain; - tensile stress-strain curves; - tensile creep; - Charpy impact strength; and - puncture impact behaviour.

Committee	E13.01
DocumentType	Standard
PublisherName	Ente Nazionale Italiano di Unificazione (UNI)
Status	Superseded
SupersededBy	UNI EN ISO 11403-1:2021
Supersedes	UNI EN ISO 11403-1 : 2004

Standards	Relationship
BS EN ISO 11403-1:2014	Identical
DIN EN ISO 11403-1:2014-09	Identical
EN ISO 11403-1:2014	Identical
I.S. EN ISO 11403-1:2014	Identical
ISO 11403-1:2014	Identical
NF EN ISO 11403-1 : 2014	Identical
NS EN ISO 11403-1 : 2014	Identical
SN EN ISO 11403-1 : 2014	Identical
ONORM EN ISO 11403-1 : 2014	Identical
NEN EN ISO 11403-1 : 2014	Identical
NBN EN ISO 11403-1 : 2014	Identical
DIN EN ISO 11403-1 E : 2003	Identical
UNE-EN ISO 11403-1:2014	Identical
DIN EN ISO 11403-1:2003-09	Identical

ISO 6603-2:2000	Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing
ISO 15850:2014	Plastics Determination of tension-tension fatigue crack propagation Linear elastic fracture mechanics (LEFM) approach
ISO 6721-2:2008	Plastics Determination of dynamic mechanical properties Part 2: Torsion-pendulum method
ISO 293:2004	Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 294-3:2002	Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates
ISO 295:2004	Plastics — Compression moulding of test specimens of thermosetting materials
ISO 10350-1:2017	Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
ISO 10724-1:1998	Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
ISO 527-2:2012	Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 17281:2002	Plastics Determination of fracture toughness (GIC and KIC) at moderately high loading rates (1 m/s)
ISO 179-1:2010	Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 6721-4:2008	Plastics Determination of dynamic mechanical properties Part 4: Tensile vibration Non-resonance method
ISO 294-1:2017	Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 2818:1994	Plastics — Preparation of test specimens by machining
ISO 899-1:2017	Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 20753:2008	Plastics Test specimens
ISO 13586:2000	Plastics Determination of fracture toughness (GIC and KIC) Linear elastic fracture mechanics (LEFM) approach
ISO 527-1:2012	Plastics Determination of tensile properties Part 1: General principles
ISO 10724-2:1998	Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates