Name: UNI EN ISO 17078-3 : 2009
Brand: UNI

PETROLEUM AND NATURAL GAS INDUSTRIES - DRILLING AND PRODUCTION EQUIPMENT - PART 3: RUNNING TOOLS, PULLING TOOLS AND KICK-OVER TOOLS AND LATCHES FOR SIDE-POCKET MANDRELS

Published date

10-08-2009

Publisher

Ente Nazionale Italiano di Unificazione (UNI)

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Functional specification
  5.1 General
  5.2 Functional characteristics
  5.3 Well parameters
  5.4 Operational parameters
  5.5 Environmental service grades (class designation)
  5.6 Design validation grades
  5.7 Product functional testing grades
  5.8 Quality grades
  5.9 Additional testing
6 Technical specification
  6.1 General requirements
  6.2 Technical requirements
  6.3 Design criteria
  6.4 Allowable design changes
  6.5 Design verification and validation requirements
  6.6 Product functional testing requirements
7 Supplier/manufacturer requirements
  7.1 General
  7.2 Documentation and data control
  7.3 Product identification requirements
  7.4 Quality control requirements
  7.5 Heat treatment requirements
  7.6 Welding requirements
  7.7 Non-destructive examination (NDE) requirements
  7.8 Storage and shipping preparation
  7.9 Allowable changes after manufacturing
  7.10 Reconditioning and repair of used running, pulling
       and kick-over tools and latches
Annex A (normative) - Requirements for running and pulling
        tools
Annex B (normative) - Requirements for kick-over tools
Annex C (normative) - Requirements for latches
Annex D (normative) - Side-pocket mandrel tool interface
        evaluations
Annex E (informative) - Figures
Bibliography

Supplies requirements and guidelines for running tools, pulling tools, kick-over tools and latches used for the installation and retrieval of flow control and other devices to be installed in side-pocket mandrels for use in the petroleum and natural gas industries. Also covers requirements for specifying, selecting, designing, manufacturing, quality control, testing and preparation for shipping of these tools and latches. Additionally, it includes information regarding performance testing and calibration procedures.

Committee	CT 700
DocumentType	Standard
PublisherName	Ente Nazionale Italiano di Unificazione (UNI)
Status	Current

Standards	Relationship
ISO 17078-3:2009	Identical
EN ISO 17078-3:2009	Identical

ISO 6507-1:2005	Metallic materials Vickers hardness test Part 1: Test method
ISO/IEC 17025:2005	General requirements for the competence of testing and calibration laboratories
ISO 80000-4:2006	Quantities and units Part 4: Mechanics
ISO 6506-1:2014	Metallic materials Brinell hardness test Part 1: Test method
ISO 6508-1:2016	Metallic materials — Rockwell hardness test — Part 1: Test method
ISO 6892:1998	Metallic materials Tensile testing at ambient temperature
NACE MR 01 75 : 2003	METALS FOR SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING RESISTANCE IN SOUR OILFIELD ENVIRONMENTS
ISO 31-0:1992	Quantities and units Part 0: General principles
ISO 9000:2015	Quality management systems — Fundamentals and vocabulary
ISO 3601-1:2012	Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes
ISO 17078-2:2007	Petroleum and natural gas industries — Drilling and production equipment — Part 2: Flow-control devices for side-pocket mandrels
SAE AMS H 6875 : 2010	HEAT TREATMENT OF STEEL RAW MATERIALS
ISO 3601-3:2005	Fluid power systems O-rings Part 3: Quality acceptance criteria
ISO 17078-1:2004	Petroleum and natural gas industries — Drilling and production equipment — Part 1: Side-pocket mandrels
ISO 18265:2013	Metallic materials — Conversion of hardness values
ISO/IEC Guide 22:1996	General criteria for supplier's declaration of conformity