UNI EN ISO 3269 : 2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
09-08-2022
01-01-2002
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and conditions
4 General principles and requirements
5 Acceptance inspection procedure for fastener
characteristics
Annex A (informative) Recommendations for acceptance-
inspection procedures (for example, for dimensional
characteristics)
Annex B (informative) Guidance and explanation
concerning the principle of this international
standard
Bibliography
Gives the procedure to be followed by the purchaser at his acceptance inspection so as to decide whether a lot of fasteners may be accepted or rejected, when another acceptance procedure has not been agreed.
| DevelopmentNote |
Supersedes UNI 3740-8. (05/2002)
|
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN ISO 3269 : 2000 | Identical |
| ISO 3269:2000 | Identical |
| EN ISO 3269:2000 | Identical |
| NBN EN ISO 3269 : 2000 | Identical |
| NF EN ISO 3269 : 2000 | Identical |
| DIN EN ISO 3269:2000-11 | Identical |
| BS EN ISO 3269:2001 | Identical |
| NS EN ISO 3269 : 1ED 2000 | Identical |
| I.S. EN ISO 3269:2000 | Identical |
| NEN EN ISO 3269 : 2000 | Identical |
| SN EN ISO 3269 : 2000 | Identical |
| UNI 8836 : 2013 | CONICAL SPRING WASHERS - NORMAL SERIES |
| UNI 9709 : 2010 | TWO-THREAD COUNTERSUNK (FLAT) HEAD TAPPING SCREWS WITH CROSS RECESSED FOR PLASTICS |
| UNI 6599 : 2009 | EXTERNAL TAB WASHERS - PRODUCT GRADE A |
| UNI 8837 : 2013 | CONICAL SPRING WASHERS - WIDE SERIES |
| UNI 8182 : 2010 | CROSS RECESSED COUNTERSUNK (OVAL) HEAD WOOD SCREWS |
| UNI 11545 : 2014 | PAN HEAD TAPPING SCREWS WITH CROSS RECESSED FOR PLASTICS |
| UNI 9710 : 2010 | TWO-THREAD RAISED COUNTERSUNK (OVAL) HEAD TAPPING SCREWS WITH CROSS RECESSED FOR PLASTICS MATERIALS |
| UNI 1751 : 2013 | SINGLE COIL SPRING WASHER - NORMAL SERIES - GENERAL TEST METHODS |
| UNI 6950 : 2010 | HEXAGON HEAD TAPPING SCREWS WITH COLLAR |
| UNI 9704 : 2010 | TWO-THREAD HEXAGON HEAD TAPPING SCREWS FOR PLASTICS |
| UNI 6596 : 2009 | SQUARE WASHERS WITH HOLE - PRODUCT GRADE C |
| UNI 701 : 2010 | SLOTTED ROUND HEAD WOOD SCREWS |
| UNI 8181 : 2010 | CROSS RECESSED COUNTERSUNK (FLAT) HEAD WOOD SCREWS |
| UNI 7323-12 : 2009 | FASTENERS WITH PARTICULAR CHARACTERISTICS - TECHNICAL REQUIREMENTS - TWO-THREAD TAPPING SCREWS FOR PLASTICS |
| UNI 9707 : 2010 | TWO-THREAD PAN HEAD TAPPING SCREWS WITH CROSS RECESSED FOR PLASTICS |
| UNI 9708 : 2010 | TWO-THREAD FLANGE PAN HEAD TAPPING SCREWS WITH CROSS RECESSED FOR PLASTICS |
| UNI 6595 : 2009 | PLAIN WASHERS WITH SQUARE HOLE - PRODUCT GRADE C |
| UNI 7323-13 : 2014 | FASTENERS WITH PARTICULAR CHARACTERISTICS TECHNICAL REQUIREMENTS - PART 13: TAPPING SCREWS FOR PLASTICS |
| UNI 704 : 2010 | HEXAGON HEAD WOOD SCREWS |
| UNI 11547 : 2014 | HEXAGON HEAD TAPPING SCREWS WITH COLLAR FOR PLASTICS |
| UNI 9706 : 2010 | TWO-THREAD HEXAGON HEAD TAPPING SCREWS WITH LARGE COLLAR FOR PLASTICS |
| UNI 8838 : 2013 | CONICAL SPRING WASHERS - EXTRALARGE SERIES |
| UNI 8180 : 2010 | CROSS RECESSED PAN HEAD WOOD SCREWS |
| UNI 6600 : 2009 | TAB WASHERS WITH LONG TAP - PRODUCT GRADE A |
| UNI 702 : 2010 | SLOTTED COUNTERSUNK (FLAT) HEAD WOOD SCREWS |
| UNI 11544 : 2014 | HEXAGON HEAD TAPPING SCREWS FOR PLASTICS |
| UNI 8116 : 2010 | Hexagon head drilling screws with tapping screws thread |
| UNI 6601 : 2009 | RECTANGULAR TAB WASHERS - PRODUCT GRADE A |
| UNI 7323-14 : 2014 | FASTENERS WITH PARTICULAR CHARACTERISTICS - TECHNICAL REQUIREMENTS - PART 14: THREAD FORMING SCREWS FOR ISO METRIC, TYPES AND DESIGNATION |
| UNI 11546 : 2014 | COUNTERSUNK (FLAT) HEAD TAPPING SCREWS WITH CROSS RECESSED FOR PLASTICS |
| UNI 9705 : 2010 | TWO-THREAD HEXAGON HEAD TAPPING SCREWS WITH COLLAR FOR PLASTICS |
| UNI 703 : 2010 | SLOTTED COUNTERSUNK (OVAL) HEAD WOOD SCREWS |
| UNI 8839 : 2013 | CURVED OR CRINKLED OPEN SPRING WASHERS - GENERAL TEST METHODS |
| UNI 11548 : 2014 | RAISED COUNTERSUNK (OVAL) HEAD TAPPING SCREWS WITH CROSS RECESSED FOR PLASTICS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.