• There are no items in your cart

02/124519 DC : DRAFT DEC 2002

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

EN 14598-2 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
Superseded date

06-28-2005

Published date

11-23-2012

EN 14598-2

Committee
PRI/42
DocumentType
Draft
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
ISO 11667:1997 Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of resin, reinforced-fibre and mineral-filler content — Dissolution methods
EN ISO 62:2008 Plastics - Determination of water absorption (ISO 62:2008)
EN ISO 14126:1999/AC:2002 FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF COMPRESSIVE PROPERTIES IN THE IN-PLANE DIRECTION
IEC 60695-2-1:1991 Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance
IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
EN ISO 527-4:1997 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 4: TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES
ISO 537:1989 Plastics Testing with the torsion pendulum
EN ISO 10724-1 : 2001 PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOSETTING POWDER MOULDING COMPOUNDS (PMCS) - PART 1: GENERAL PRINCIPLES AND MOULDING OF MULTIPURPOSE TEST SPECIMENS
EN ISO 6721-1:2011 Plastics - Determination of dynamic mechanical properties - Part 1: General principles (ISO 6721-1:2011)
ISO 11359-2:1999 Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
EN ISO 2818:1996 PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING
EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
EN ISO 10352:2010 Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of mass per unit area (ISO 10352:2010)
EN ISO 179-1:2010 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010)
ISO 11357-2:2013 Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height
ISO 3795:1989 Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials
IEC 60167:1964 Methods of test for the determination of the insulation resistance of solid insulating materials
EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
IEC 60296:2012 RLV Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
EN ISO 3167:2014 Plastics - Multipurpose test specimens (ISO 3167:2014)
ISO 1268-10:2005 Fibre-reinforced plastics — Methods of producing test plates — Part 10: Injection moulding of BMC and other long-fibre moulding compounds — General principles and moulding of multipurpose test specimens
ISO 1268-8:2004 Fibre-reinforced plastics — Methods of producing test plates — Part 8: Compression moulding of SMC and BMC
IEC 60707:1999 Flammability of solid non-metallic materials when exposed to flame sources - List of test methods
IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
ISO 2577:2007 Plastics Thermosetting moulding materials Determination of shrinkage
EN ISO 2039-1 : 2003 PLASTICS - DETERMINATION OF HARDNESS - PART 1: BALL INDENTATION METHOD (ISO 2039-1:2001)
EN ISO 12115 : 1997 FIBRE-REINFORCED PLASTICS - THERMOSETTING MOULDING COMPOUNDS AND PREPREGS - DETERMINATION OF FLOWABILITY, MATURATION AND SHELF LIFE
EN ISO 6603-2:2000 Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented puncture test (ISO 6603-2:2000)
EN ISO 10724-2 : 2000 PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOSETTING POWDER MOULDING COMPOUNDS (PMCS) - PART 2: SMALL PLATES
EN ISO 1172:1998 Textile-glass-reinforced plastics - Prepregs, moulding compounds and laminates - Determination of the textile-glass and mineral-filler content - Calcination methods (ISO 1172:1996)
EN ISO 14125:1998/A1:2011 FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF FLEXURAL PROPERTIES
EN ISO 4589-2:2017 Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test (ISO 4589-2:2017)
EN ISO 291:2008 Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008)
EN ISO 179-2:1999/A1:2012 PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - INSTRUMENTED IMPACT TEST (ISO 179-2:1997/AMD 1:2011)
EN ISO 12114 : 1997 FIBRE-REINFORCED PLASTICS - THERMOSETTING MOULDING COMPOUNDS AND PREPREGS - DETERMINATION OF CURE CHARACTERISTICS (ISO 12114:1997)
ISO 1268-11:2005 Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC and other long-fibre moulding compounds — Small plates
EN ISO 175:2010 Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010)
ISO 10351:1992 Plastics Determination of the combustibility of specimens using a 125 mm flame source

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.