05/30132920 DC : DRAFT APR 2005

Superseded View Superseded By

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

EN 1090-2 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR THE EXECUTION OF STEEL STRUCTURES

Publisher: British Standards Institution

Published: 11-23-2012

Available Formats:
More Info on product formats

Table of Contents - (Show below) - (Hide below)

Foreword
1 Scope
2 Normative references
3 Definitions
4 Specifications and documentation
5 Constituent products
6 Fabrication
7 Welding
8 Mechanical fastening
9 Erection
10 Surface treatment
11 Geometrical tolerances
12 Inspection, testing and correction
Annex A 1 (normative) List of required additional information
Annex A 2 (normative) List of options to be specified
Annex A 3 (normative) Requirements related to the execution classes
Annex B (informative) Guidance for the choice of execution classes
Annex C (informative) Typical format for a quality plan
        C.1 Scope
        C.2 Management
        C.3 Specification review
        C.4 Documentation
        C.5 Inspection and testing procedures
Annex D (informative) Selection and use of mechanical
        fasteners for sheeting
        D.1 Scope
        D.2 Selection of fastener type
        D.3 Use of Special fasteners
Annex E (informative) Welded joints in hollow sections
        E.1 Guidance for start and stop positions
        E.2 Preparation of joint faces
        E.3 Assembly for welding
Annex F (informative) Welding methods for thin gauge steel
        components
        F.1 Intermittent welding
        F.2 Lap joints
        F.3 Butt welds
Annex G (normative) Procedure test for determination of
        slip factor
        G.1 The purpose of testing
        G.2 Significant variables
        G.3 Test specimens
        G.4 Test procedure
        G.5 Extended creep test
        G.6 Test results
Annex H (normative) Use of compressible washer-type direct
        tension indicators
        H.1 Fitting
        H.2 Checking
Annex J (informative) Hexagon injection bolts
        J.1 General
        J.2 Hole sizes
        J.3 Bolts
        J.4 Washers
        J.5 Nuts
        J.6 Resin
        J.7 Tightening
        J.8 Installation
Annex K (normative) Corrosion protection
        K.1 General
        K.2 Surface preparation for carbon steels
        K.3 Welds and surfaces for welding
        K.4 Surfaces in non-friction-grip preloaded connections
        K.5 Preparation of fasteners
        K.6 Coating methods
Annex L 1 Geometrical tolerances - Essential
          tolerances (normative)
Annex L 2 Geometrical tolerances - Supplementary
          tolerances (informative)
Annex M (normative) Sequential method for bolt
        tightening inspection
        M.1 General
        M.2 Application
Bibliography

Abstract - (Show below) - (Hide below)

EN 1090-2

General Product Information - (Show below) - (Hide below)

Published
Document Type	Draft
Status	Superseded
Publisher	British Standards Institution
Pages
ISBN
Committee	B/521
Superseded By	BS EN 1090-2 : 2008
Comment Closes On

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
PREN 1090-2 : DRAFT 2015	Identical

Standards Referencing This Book - (Show below) - (Hide below)

EN 12073 : 1999	WELDING CONSUMABLES - TUBULAR CORED ELECTRODES FOR METAL ARC WELDING WITH OR WITHOUT A GAS SHIELD OF STAINLESS AND HEAT-RESISTING STEELS - CLASSIFICATION
EN 10162 : 2003	COLD ROLLED STEEL SECTIONS - TECHNICAL DELIVERY CONDITIONS - DIMENSIONAL AND CROSS-SECTIONAL TOLERANCES
PREN 14399-2 : DRAFT 2013	HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 2: SUITABILITY TEST FOR PRELOADING
PREN 15048-2 : DRAFT 2014	NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE
EN ISO 10511 : 2012	PREVAILING TORQUE TYPE HEXAGON THIN NUTS (WITH NON-METALLIC INSERT) (ISO 10511:2012)
EN 10048 : 1996	HOT ROLLED NARROW STEEL STRIP - TOLERANCES ON DIMENSIONS AND SHAPE
EN 10051 : 2010	CONTINUOUSLY HOT-ROLLED STRIP AND PLATE/SHEET CUT FROM WIDE STRIP OF NON-ALLOY AND ALLOY STEELS - TOLERANCES ON DIMENSIONS AND SHAPE
ISO 1479 : 2011(R2016)	HEXAGON HEAD TAPPING SCREWS
EN 439 : 1994	WELDING CONSUMABLES - SHIELDING GASES FOR ARC WELDING AND CUTTING
EN ISO 6789 : 2003	ASSEMBLY TOOLS FOR SCREWS AND NUTS - HAND TORQUE TOOLS - REQUIREMENTS AND TEST METHODS FOR DESIGN CONFORMANCE TESTING, QUALITY CONFORMANCE TESTING AND RECALIBRATION PROCEDURE (ISO 6789:2003)
EN ISO 7040 : 2012	PREVAILING TORQUE TYPE HEXAGON REGULAR NUTS (WITH NON-METALLIC INSERT) - PROPERTY CLASSES 5, 8 AND 10 (ISO 7040:2012)
EN 440 : 1994	WELDING CONSUMABLES - WIRE ELECTRODES AND DEPOSITS FOR GAS SHIELDED METAL ARC WELDING OF NON ALLOY AND FINE GRAIN STEELS - CLASSIFICATION
EN 10140 : 2006	COLD ROLLED NARROW STEEL STRIP - TOLERANCES ON DIMENSIONS AND SHAPE
EN 10079 : 2007	DEFINITION OF STEEL PRODUCTS
EN 10025-4 : 2004	HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 4: TECHNICAL DELIVERY CONDITIONS FOR THERMOMECHANICAL ROLLED WELDABLE FINE GRAIN STRUCTURAL STEELS
EN 10149-1 : 2013	HOT ROLLED FLAT PRODUCTS MADE OF HIGH YIELD STRENGTH STEELS FOR COLD FORMING - PART 1: GENERAL TECHNICAL DELIVERY CONDITIONS
EN 10027-2 : 2015	DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM
EN 10029 : 2010	HOT-ROLLED STEEL PLATES 3 MM THICK OR ABOVE - TOLERANCES ON DIMENSIONS AND SHAPE
EN ISO 3506-1 : 2009	MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 1: BOLTS, SCREWS AND STUDS
EN 10056-2 : 1993	STRUCTURAL STEEL EQUAL AND UNEQUAL LEG ANGLES - PART 2: TOLERANCES ON SHAPE AND DIMENSIONS
PREN 14399-5 : DRAFT 2013	HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS
EN 756 : 2004	WELDING CONSUMABLES - SOLID WIRES, SOLID WIRE-FLUX AND TUBULAR CORED ELECTRODE-FLUX COMBINATIONS FOR SUBMERGED ARC WELDING OF NON ALLOY AND FINE GRAIN STEELS - CLASSIFICATION
EN 10164 : 2004	STEEL PRODUCTS WITH IMPROVED DEFORMATION PROPERTIES PERPENDICULAR TO THE SURFACE OF THE PRODUCT - TECHNICAL DELIVERY CONDITIONS
EN ISO 7042 : 2012	PREVAILING TORQUE TYPE ALL-METAL HEXAGON HIGH NUTS - PROPERTY CLASSES 5, 8, 10 AND 12 (ISO 7042:2012)
EN 10279 : 2000	HOT ROLLED STEEL CHANNELS - TOLERANCES ON SHAPE, DIMENSIONS AND MASS
EN 10088-3 : 2014	STAINLESS STEELS - PART 3: TECHNICAL DELIVERY CONDITIONS FOR SEMIFINISHED PRODUCTS, BARS, RODS, WIRE, SECTIONS AND BRIGHT PRODUCTS OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES
EN ISO 15979 : 2002	OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND PROTRUDING HEAD ST/ST
PREN 13479 : DRAFT 2014	WELDING CONSUMABLES - GENERAL PRODUCT STANDARD FOR FILLER METALS AND FLUXES FOR FUSION WELDING OF METALLIC MATERIALS
ISO 10509 : 2012(R2017)	HEXAGON FLANGE HEAD TAPPING SCREWS
EN 10149-2 : 2013	HOT ROLLED FLAT PRODUCTS MADE OF HIGH YIELD STRENGTH STEELS FOR COLD FORMING - PART 2: TECHNICAL DELIVERY CONDITIONS FOR THERMOMECHANICALLY ROLLED STEELS
EN 10034 : 1993	STRUCTURAL STEEL I AND H SECTIONS - TOLERANCES ON SHAPE AND DIMENSIONS
EN ISO 7719 : 2012	PREVAILING TORQUE TYPE ALL-METAL HEXAGON REGULAR NUTS - PROPERTY CLASSES 5, 8 AND 10 (ISO 7719:2012)
ISO 7049 : 2011(R2016)	CROSS-RECESSED PAN HEAD TAPPING SCREWS
EN 12535 : 2000	WELDING CONSUMABLES - TUBULAR CORED ELECTRODES FOR GAS SHIELDED METAL ARC WELDING OF HIGH STRENGTH STEELS - CLASSIFICATION
EN ISO 15976 : 2002	CLOSED END BLIND RIVETS WITH BREAK PULL MANDREL AND PROTRUDING HEAD - ST/ST
PREN 14399-4 : DRAFT 2013	HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES
EN 20898-2 : 1993	MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
EN 10025-1 : 2004	HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 1: GENERAL TECHNICAL DELIVERY CONDITIONS
EN 10088-2 : 2014	STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES
EN 10131 : 2006	COLD ROLLED UNCOATED AND ZINC OR ZINC-NICKEL ELECTROLYTICALLY COATED LOW CARBON AND HIGH YIELD STRENGTH STEEL FLAT PRODUCTS FOR COLD FORMING - TOLERANCES ON DIMENSIONS AND SHAPE
EN 10024 : 1995	HOT ROLLED TAPER FLANGE I SECTIONS - TOLERANCES ON SHAPE AND DIMENSIONS
EN 10210-1 : 2006	HOT FINISHED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 1: TECHNICAL DELIVERY CONDITIONS
EURONORM 60 : 1977	HOT-ROLLED ROUND STEEL FOR GENERAL USE
EN 10327 : 2004	CONTINUOUSLY HOT-DIP COATED STRIP AND SHEET OF LOW CARBON STEELS FOR COLD FORMING - TECHNICAL DELIVERY CONDITIONS
EN 10028-7 : 2016	FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 7: STAINLESS STEELS
EN ISO 1127 : 1996	STAINLESS STEEL TUBES - DIMENSIONS, TOLERANCES AND CONVENTIONAL MASSES PER UNIT LENGTH
EN 10210-2 : 2006 COR 2007	HOT FINISHED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 2: TOLERANCES, DIMENSIONS AND SECTIONAL PROPERTIES
EN 10326 : 2004	CONTINUOUSLY HOT-DIP COATED STRIP AND SHEET OF STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS
EN 10163-2 : 2004	DELIVERY REQUIREMENTS FOR SURFACE CONDITION OF HOT-ROLLED STEEL PLATES, WIDE FLATS AND SECTIONS - PART 2: PLATE AND WIDE FLATS
EN 10163-1 : 2004 COR 2007	DELIVERY REQUIREMENTS FOR SURFACE CONDITION OF HOT-ROLLED STEEL PLATES, WIDE FLATS AND SECTIONS - PART 1: GENERAL REQUIREMENTS
EN 10272 : 2016	STAINLESS STEEL BARS FOR PRESSURE PURPOSES
EN 10219-1 : 2006	COLD FORMED WELDED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 1: TECHNICAL DELIVERY CONDITIONS
ISO 1481 : 2011(R2016)	SLOTTED PAN HEAD TAPPING SCREWS
EN 10143 : 2006	CONTINUOUSLY HOT-DIP METAL COATED STEEL SHEET AND STRIP - TOLERANCES ON DIMENSIONS AND SHAPE
EURONORM 65 : 1980	HOT-ROLLED ROUND STEEL FOR SCREWS AND RIVETS
EN 10021 : 2006	GENERAL TECHNICAL DELIVERY CONDITIONS FOR STEEL PRODUCTS
EURONORM 61 : 1982	HOT-ROLLED HEXAGON STEEL
EURONORM 58 : 1978	HOT-ROLLED FLAT STEEL FOR GENERAL USE
EN ISO 2320 : 2015	FASTENERS - PREVAILING TORQUE STEEL NUTS - FUNCTIONAL PROPERTIES (ISO 2320:2015)
PREN 14399-3 : DRAFT 2013	HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES
EN ISO 10513 : 2012	PREVAILING TORQUE TYPE ALL-METAL HEXAGON HIGH NUTS WITH METRIC FINE PITCH THREAD - PROPERTY CLASSES 8, 10 AND 12 (ISO 10513:2012)
EN 10056-1 : 2017 COR 2017	STRUCTURAL STEEL EQUAL AND UNEQUAL LEG ANGLES - PART 1: DIMENSIONS
EN 10025-5 : 2004	HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 5: TECHNICAL DELIVERY CONDITIONS FOR STRUCTURAL STEELS WITH IMPROVED ATMOSPHERIC CORROSION RESISTANCE
EN 10163-3 : 2004	DELIVERY REQUIREMENTS FOR SURFACE CONDITION OF HOT-ROLLED STEEL PLATES, WIDE FLATS AND SECTIONS - PART 3: SECTIONS
EN 12072 : 1999	WELDING CONSUMABLES - WIRE ELECTRODES, WIRES AND RODS FOR ARC WELDING OF STAINLESS AND HEAT-RESISTING STEELS - CLASSIFICATION
EN 760 : 1996	WELDING CONSUMABLES - FLUXES FOR SUBMERGED ARC WELDING - CLASSIFICATION
EN 10204 : 2004	METALLIC PRODUCTS - TYPES OF INSPECTION DOCUMENTS
EN 10025-2 : 2004 COR 2005	HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
ISO 4997 : 2015	COLD-REDUCED CARBON STEEL SHEET OF STRUCTURAL QUALITY
EN 1600 : 1997	WELDING CONSUMABLES - COVERED ELECTRODES FOR MANUAL METAL ARC WELDING OF STAINLESS AND HEAT RESISTING STEELS - CLASSIFICATION
EN 499 : 1994	WELDING CONSUMABLES - COVERED ELECTRODES FOR MANUAL METAL ARC OF NON ALLOY AND FINE GRAIN STEELS - CLASSIFICATION
EN ISO 898-1 : 2013	MECHANICAL PROPERTIES OF FASTENERS MADE OF CARBON STEEL AND ALLOY STEEL - PART 1: BOLTS, SCREWS AND STUDS WITH SPECIFIED PROPERTY CLASSES - COARSE THREAD AND FINE PITCH THREAD (ISO 898-1:2013)
EN 10027-1 : 2016	DESIGNATION SYSTEMS FOR STEELS - PART 1: STEEL NAMES
EN 10025-6 : 2004 + A1 2009	HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 6: TECHNICAL DELIVERY CONDITIONS FOR FLAT PRODUCTS OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN THE QUENCHED AND TEMPERED CONDITION
PREN 14399-8 : DRAFT 2015	HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES
EN 10020 : 2000	DEFINITION AND CLASSIFICATION OF GRADES OF STEEL
EN 10219-2 : 2006	COLD FORMED WELDED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 2: TOLERANCES, DIMENSIONS AND SECTIONAL PROPERTIES
EN 758 : 1997	WELDING CONSUMABLES - TUBULAR COVERED ELECTRODES FOR METAL ARC WELDING WITH AND WITHOUT A GAS SHIELD OF NON ALLOY AND FINE GRAIN STEELS - CLASSIFICATION
EN ISO 10684 : 2004 COR 2009	FASTENERS - HOT DIP GALVANIZED COATINGS (ISO 10684:2004)
EN ISO 15980 : 2002	OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND COUNTERSUNK HEAD ST/ST
EN ISO 15480 : 1999	HEXAGON WASHER HEAD DRILLING SCREWS WITH TAPPING SCREW THREAD
EN 10055 : 1995	HOT ROLLED STEEL EQUAL FLANGE TEES WITH RADIUSED ROOT AND TOES - DIMENSIONS AND TOLERANCES ON SHAPE AND DIMENSIONS
EURONORM 59 : 1978	HOT-ROLLED SQUARE STEEL FOR GENERAL USE
EN 10258 : 1997	COLD-ROLLED STAINLESS STEEL AND NARROW STRIP AND CUT LENGTHS - TOLERANCES AND DIMENSIONS AND SHAPE
PREN 14399-7 : DRAFT 2015	HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES
PREN 10217-7 : DRAFT 2009	WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 7: STAINLESS STEEL TUBES
PREN 14399-9 : DRAFT 2015	HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES
EN ISO 15984 : 2002	OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND COUNTERSUNK HEAD A2/A2
EN 10025-3 : 2004	HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 3: TECHNICAL DELIVERY CONDITIONS FOR NORMALIZED/NORMALIZED ROLLED WELDABLE FINE GRAIN STRUCTURAL STEELS
EN ISO 15983 : 2002	OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND PROTRUDING HEAD A2/A2
EN 10259 : 1997	COLD-ROLLED STAINLESS STEEL WIDE STRIP AND PLATE/SHEET - TOLERANCES ON DIMENSIONS AND SHAPE
EN ISO 10512 : 2012	PREVAILING TORQUE TYPE HEXAGON REGULAR NUTS (WITH NON-METALLIC INSERT) WITH METRIC FINE PITCH THREAD - PROPERTY CLASSES 6, 8 AND 10 (ISO 10512:2012)
EN 12534 : 1999	WELDING CONSUMABLES - WIRE ELECTRODES, WIRES, RODS AND DEPOSITS FOR GAS SHIELDED METAL ARC WELDING OF HIGH STRENGTH STEELS - CLASSIFICATION
EN 10149-3 : 2013	HOT ROLLED FLAT PRODUCTS MADE OF HIGH YIELD STRENGTH STEELS FOR COLD FORMING - PART 3: TECHNICAL DELIVERY CONDITIONS FOR NORMALIZED OR NORMALIZED ROLLED STEELS
EN 757 : 1997	WELDING CONSUMABLES - COVERED ELECTRODES FOR MANUAL METAL ARC WELDING OF HIGH STRENGTH STEELS - CLASSIFICATION
EURONORM 17 : 1970	WIRE ROD OF COMMON UNALLOYED STEELS FOR DRAWING; DIMENSIONS AND PERMISSIBLE DEVIATIONS
EN ISO 3506-2 : 2009	MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 2: NUTS (ISO 3506-2:2009)
PREN 14399-6 : DRAFT 2013	HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS

Sorry this product is not available in your region.

05/30132920 DC : DRAFT APR 2005

Table of Contents - (Show below) - (Hide below)

Abstract - (Show below) - (Hide below)

General Product Information - (Show below) - (Hide below)

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Standards Referencing This Book - (Show below) - (Hide below)

Add To Cart

Publisher

Category

Sub Category

Access your standards online with a subscription?