• 11/30211183 DC : 0

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    BS ISO 16422 - PIPES AND JOINTS MADE OF ORIENTED UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-O) FOR THE CONVEYANCE OF WATER UNDER PRESSURE - SPECIFICATIONS

    Available format(s):  Hardcopy, PDF

    Superseded date:  02-28-2014

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Material
    6 Effect of materials on water quality
    7 Material classification
    8 Classification and selection of pipes
    9 General requirements for pipes
    10 Geometrical characteristics for pipes
    11 Mechanical characteristics of pipes
    12 Physical characteristics
    13 Mechanical characteristics of assemblies, including
       joints
    14 Elastomeric seals
    15 Marking
    Annex A (normative) - Establishment of the pipe
            material classification
    Annex B (informative) - Minimum depth of engagement
            of sockets
    Annex C (normative) - Temperature derating factor
    Annex D (informative) - Ring stiffness of pipes
    Annex E (informative) - Determination of the long-term
            test pressure by creep consideration
    Annex F (informative) - Determination of axial and tangential
            orientation factor

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee PRI/88/2
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 2507-2:1995 Thermoplastics pipes and fittings Vicat softening temperature Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (vinyl chloride) (PVC-HI) pipes
    ISO 6259-2:1997 Thermoplastics pipes Determination of tensile properties Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI)
    ISO 13846:2000 Plastics piping systems End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping Test method for long-term leaktightness under internal water pressure
    ISO 2507-1:1995 Thermoplastics pipes and fittings Vicat softening temperature Part 1: General test method
    ISO 3127:1994 Thermoplastics pipes Determination of resistance to external blows Round-the-clock method
    ISO 161-1:1996 Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series
    ISO 9080:2012 Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
    ISO 3:1973 Preferred numbers Series of preferred numbers
    ISO 1452-5:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 5: Fitness for purpose of the system
    ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids Dimensions and tolerances Part 1: Metric series
    ISO 13783:1997 Plastics piping systems — Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints — Test method for leaktightness and strength while subjected to bending and internal pressure
    ISO 13844:2015 Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with plastic pressure pipes Test method for leaktightness under negative pressure, angular deflection and deformation
    ISO 1452-2:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 2: Pipes
    ISO 18373-1:2007 Rigid PVC pipes Differential scanning calorimetry (DSC) method Part 1: Measurement of the processing temperature
    ISO 1628-2:1998 Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 2: Poly(vinyl chloride) resins
    ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
    ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
    ISO 2531:2009 Ductile iron pipes, fittings, accessories and their joints for water applications
    ISO 4633:2015 Rubber seals Joint rings for water supply, drainage and sewerage pipelines Specification for materials
    ISO 9852:2007 Unplasticized poly(vinyl chloride) (PVC-U) pipes Dichloromethane resistance at specified temperature (DCMT) Test method
    ISO 7686:2005 Plastics pipes and fittings Determination of opacity
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    ISO 2505:2005 Thermoplastics pipes Longitudinal reversion Test method and parameters
    ISO 13845:2015 Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes Test method for leaktightness under internal pressure and with angular deflection
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective