ISO 13953:2001
|
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
|
ISO 10838-3:2001
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
|
ISO 1133-1:2011
|
Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
|
ISO 13956:2010
|
Plastics pipes and fittings Decohesion test of polyethylene (PE) saddle fusion joints Evaluation of ductility of fusion joint interface by tear test
|
ISO 12176-4:2003
|
Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 4: Traceability coding
|
ISO 10838-2:2000
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
|
ISO 10838-1:2000
|
Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
|
ISO 1167-4:2007
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
|
ISO 16010:2005
|
Elastomeric seals Material requirements for seals used in pipes and fittings carrying gaseous fuels and hydrocarbon fluids
|
ISO/TS 10839:2000
|
Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation
|
ISO 13957:1997
|
Plastics pipes and fittings — Polyethylene (PE) tapping tees — Test method for impact resistance
|
IEC 60364-1:2005
|
Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
|
ISO 3126:2005
|
Plastics piping systems Plastics components Determination of dimensions
|
ISO 11922-1:1997
|
Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
|
ISO 7-1:1994
|
Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
|
HD 60364-1:2008/A11:2017
|
LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 1: FUNDAMENTAL PRINCIPLES, ASSESSMENT OF GENERAL CHARACTERISTICS, DEFINITIONS
|
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV
|
Degrees of protection provided by enclosures (IP Code)
|
ISO 13954:1997
|
Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
|
ISO 13955:1997
|
Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
|
ISO 11357-6:2008
|
Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
|
EN 60335-1:2012/A13:2017
|
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
|
CEN/TS 1555-7:2013
|
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
|
ISO 13950:2007
|
Plastics pipes and fittings Automatic recognition systems for electrofusion joints
|
EN 12117:1997
|
Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships
|
ISO 13951:2015
|
Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading
|
ISO 228-1:2000
|
Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
|
ISO 1167-1:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
|