• There are no items in your cart

13/30231511 DC : 0

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

BS ISO 13577-2 - INDUSTRIAL FURNACES AND ASSOCIATED PROCESSING EQUIPMENT - SAFETY - PART 2: COMBUSTION AND FUEL HANDLING SYSTEMS
Available format(s)

Hardcopy , PDF

Superseded date

09-30-2014

Language(s)

English

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Safety Requirements, Measures and Verification
  Means
5 Verification of the safety requirements and/or
  measures
6 Information for Use
Annex A (informative) - List of significant hazards
Annex B (informative) - Typical examples of fuels
        and burners
Annex C (informative) - Typical example of piping
        and components
Annex D (informative) - Methods for burner start-up
Annex E (normative) - Maximum allowed pressure
Annex F (informative) - Examples for the determination
        of safety integrity level SIL using the risk graph
        method
Annex G (normative) - Requirements specific to Japan
Annex H (normative) - Requirements specific to the
        USA
Annex I (normative) - Requirements for Europe and
        associated countries
Bibliography

BS ISO 13577-2

Committee
RHE/13
DocumentType
Draft
Pages
104
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

EN 730-2:2002 Gas welding equipment - Safety devices - Part 2: Not incorporating a flame (flashback) arrestor
EN 10208-2:2009 Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 2: Pipes of requirement class B
EN 1539:2015 Dryers and ovens, in which flammable substances are released - Safety requirements
EN 13480-2:2017 Metallic industrial piping - Part 2: Materials
FM 3510 : 2000 FLOW AND PRESSURE SAFETY SWITCHES
ISO 7005-2:1988 Metallic flanges — Part 2: Cast iron flanges
NFPA 31 : 2016 INSTALLATION OF OIL-BURNING EQUIPMENT
ISO 8434-1:2007 Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors
CFR 29(PTS1900-1910) : 0 LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR
FM 3545 : 1998 TEMPERATURE LIMIT AND SUPERVISORY SWITCHES
EN 1057:2006+A1:2010 Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications
EN 1643:2014 Safety and control devices for gas burners and gas burning appliances - Valve proving systems for automatic shut-off valves
NFPA 79 : 2015 ELECTRICAL STANDARD FOR INDUSTRIAL MACHINERY
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
ISO 23551-4:2005 Safety and control devices for gas burners and gas-burning appliances Particular requirements Part 4: Valve-proving systems for automatic shut-off valves
ISO 7005-3:1988 Metallic flanges Part 3: Copper alloy and composite flanges
EN 751-2:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds
ISO 23551-3:2005 Safety and control devices for gas burners and gas-burning appliances Particular requirements Part 3: Gas/air ratio controls, pneumatic type
ISO 14118:2000 Safety of machinery Prevention of unexpected start-up
IEC 60730-2-6:2015 Automatic electrical controls - Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements
ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
EN 1797:2001 Cryogenic vessels - Gas/material compatibility
ISO 23553-1:2014 Safety and control devices for oil burners and oil-burning appliances Particular requirements Part 1: Automatic and semi-automatic valves
ISO 5817:2014 Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections
ISO 13574:2015 Industrial furnaces and associated processing equipment — Vocabulary
ISO 8434-2:2007 Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors
EN 1854:2010 Pressure sensing devices for gas burners and gas burning appliances
EN 12300 : 1998 AMD 1 2006 CRYOGENIC VESSELS - CLEANLINESS FOR CRYOGENIC SERVICE
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
NFPA 55 : 2016 COMPRESSED GASES AND CRYOGENIC FLUIDS CODE
EN 125:2010+A1:2015 Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices
NFPA 86 : 2015 OVENS AND FURNACES
ISO 23552-1:2007 Safety and control devices for gas and/or oil burners and gas and/or oil appliances — Particular requirements — Part 1: Fuel/air ratio controls, electronic type
ISO 8434-3:2005 Metallic tube connections for fluid power and general use — Part 3: O-ring face seal connectors
ISO 19879:2010 Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections
ISO 23551-1:2012 Safety and control devices for gas burners and gas-burning appliances Particular requirements Part 1: Automatic and semi-automatic valves
ISO 23551-2:2006 Safety and control devices for gas burners and gas-burning appliances Particular requirements Part 2: Pressure regulators
NFPA 70 : 2017 NATIONAL ELECTRICAL CODE
EN 10241:2000 Steel threaded pipe fittings
ISO 22968:2010 Forced draught oil burners
IEC 60730-2-5:2013+AMD1:2017 CSV Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems
EN 751-1:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds
EN 298:2012 Automatic burner control systems for burners and appliances burning gaseous or liquid fuels
ISO 7005-1:2011 Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems
NFPA 54 : 2018 NATIONAL FUEL GAS CODE
EN 730-1:2002 Gas welding equipment - Safety devices - Part 1: Incorporating a flame (flashback) arrestor
IEC 62061:2005+AMD1:2012+AMD2:2015 CSV Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems
EN 1547:2001+A1:2009 Industrial thermoprocessing equipment - Noise test code for industrial thermoprocessing equipment including its ancillary handling equipment
CGA G 4.4 : 2012 OXYGEN PIPELINE AND PIPING SYSTEMS
EN 331:2015 Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings
EN 10208-1:2009 Steel pipes for pipelines for combustible fluids - Technical delivery condi-tions - Part 1: Pipes of requirement class A
CGA G 4.1 : 2009 CLEANING EQUIPMENT FOR OXYGEN SERVICE
EN 10220:2002 Seamless and welded steel tubes - Dimensions and masses per unit length
EN 10242:1994/A2:2003 THREADED PIPE FITTING IN MALLEABLE CAST IRON
ICC 2012 INTERNATIONAL FUEL GAS CODE : 2012 INTERNATIONAL FUEL GAS CODE
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
ISO 23550:2011 Safety and control devices for gas burners and gas-burning appliances General requirements
EN 10217-1:2002/A1:2005 WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - NON-ALLOY STEEL TUBES WITH SPECIFIED ROOM TEMPERATURE PROPERTIES
EN 10255:2004+A1:2007 Non-Alloy steel tubes suitable for welding and threading - Technical delivery conditions
ISO 22967:2010 Forced draught gas burners
EN 525:2009 Non-domestic direct gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW

View more information
US$52.71
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.